Show off your Sak mod's!
-
The above was made with left over parts. It's grown on me but has schoolboy errors hidden:
- Pre-peening, the saw kept hitting the scale liner so I added an extra tool liner to provide clearance.
- The scale wood was Red Heart. I tried to scorch over a metal Swiss cross to leave an imprint in the wood. That didn't work, so ran a blow torch over the length of the scales, wire wooled them and waxed to cover up the error.
- I glued on the scale with the corkscrew closed. This pushed down the scale slightly so that it did not line up nicely with the scale liner. Liberal filing tidied things up.
Amateurish, but lessons learned.
-
I always add an extra liner if I am putting a saw next to a outside liner as, like you, I always find it eventually hits it and starts taking lumps out of the alu. The wood saws especially have a propensity to bend so I find the extra liner gives you that extra bit of leeway.
-
- Pre-peening, the saw kept hitting the scale liner so I added an extra tool liner to provide clearance.
I use blue painter's tape when I’m being careful, like with brand new or really old ones. Folded over the tool and sealed to itself is all it needs. That’s also what I do with leftover sharp parts that I store and organize with small zip locks.
-

Fresh from the kamakiri forge…

-
Lightweight Huntsman:
-
Wood scales
-
Old style scissors, screwed pivot, no back tool
-
Combo tool is a bit stiff, hopefully it will loosen up

-
-
@SAKTaschenmesser said:
Lightweight Huntsman:- Wood scales
- Old style scissors, screwed pivot, no back tool
- Combo tool is a bit stiff, hopefully it will loosen up
Very nice, did you make the wood handles ?
-
Noooo, way beyond the reach of my abilities.
From EBay, a Russian seller, I assumed they were Victorinox OEM.
Sent from my iPad using Tapatalk
-
@SAKTaschenmesser said:
Lightweight Huntsman:- Wood scales
- Old style scissors, screwed pivot, no back tool
- Combo tool is a bit stiff, hopefully it will loosen up
Can’t argue with that combo

-
Yes, my favourite toolset is:
(1) Blade/Combo
(2) Wood saw
(3) ScissorsThe Lightweight Huntsman.
I have limited tools and experience, but have made up one 91mm with red scales and another with wood scales.
This is my latest, and last, I've got enough!
84mm in Alox.
I was going to make it in red scales, but Myron tempted me with Alox, which I've never done before.
The peening is rough, but it works. I think I need to hammer it home further. Unfortunately there is a hammer mark just below the pivot north of the cross. I was using a punch to round off the pivots and it slipped. Impatience and lack of attention to detail.
Many thanks to the generosity of Myron who supplied most of the parts.

-
Such a cool knife! And you did a great job peening those pins over. So fun to see how this looks in an 84 mm frame, too.
Excellent work, @SAKTaschenmesser!
Myron
-
It’s a great toolset, and nice work so far!

The nice thing about errant mark in your own knife is you get to use it without worry about doing any cosmetic damage.
A small radius ball peen hammer might help tighten the rivets as needed. I use a heavy hand to set the rivets and fill the conical seat in Alox or brass bushings, but small lighter taps for rounding exposed rivets (if not setting them flush/flat to the level of the alox face). Small radius helps to ‘safely’ work closer to the edge of the domed head. Light taps, using wrist action only.
-
Great mod!
But...@SAKTaschenmesser said:
This is my latest, and last, I've got enough!Yeah, right!
-
An example might help show what I mean about the peening and finishing.
This is a before and after of a 91mm center/3rd pin that was flattened on the backside when reused and re-set in a mod.
The peening marks are made close and small enough to resemble a golf ball or mirror/disco ball somewhat and are fine enough to be sanded or polished away.
Just takes a little more time and some patience.


-
Thanks, the knife's tools are pretty tight. If I do feel a bit of wobble develop, I'll give the pivots some fairly gentle, progressive taps with the ball of my hammer to get it just right. I quite like the hammered golf ball look.
-
@SAKTaschenmesser said:
Thanks, the knife's tools are pretty tight. If I do feel a bit of wobble develop, I'll give the pivots some fairly gentle, progressive taps with the ball of my hammer to get it just right. I quite like the hammered golf ball look.
I didn’t mean to confuse the issue regarding tightening. I only meant that as a ‘if needed’ part of the discussion. Like needing to refinish after additional tightening. I’m primarily demonstrating a finishing technique I use after the rivet and tools are set. So mainly to show the difference in cosmetics. My example above was already tight, but with that big ugly flat top.
I hope that helps you and anyone else looking to improve the finish of their peening work. It’s just a matter of removing the large ‘facets’ and replacing them with smaller finer ones that can easily be made to ‘disappear’, wear, or polish away. :)
-
Say bye-bye to the compact,, it was my Xmas gift, ah man am I nervous,,
JR
-
I guess there’s no turning around,, :-
JR
-
Update, I needed a break, yeah that’s a Philips on the back rather then a corkscrew, I just don’t see the point of one, and yeah there’s an extra layer, but what could it be?

JR
-
All peened and ready for scales!
JR
-
Who’s ready for the end product? Any guesses on that 3rd layer before I post a pic?
JR
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login