Titanium?
-
@Singh said:
I just remembered: I have a SAK with Ti scales and liners.I knew I was going somewhere with this.:DI was thinking about dissimilar metals and galling. Some folks carbidize the Ti to prevent that.
Wasn’t that just a fad for knife makers like a decade ago? Blade edges and lock faces and such mods to Ti to wring more money out of the knife market?

Doesn’t seem like a great idea to try to make the liners that much harder than the tools. I don’t see the issue with dissimilar metals concerning Ti and Stainless. Galling issues sound more like fabrication and design issues to me.

-
@ComboTool said:
I know Syph does this. I've never observed galling myself but out of precaution I add washers between the tools and the titanium scales or liners.Aha! Does he still do this?
Agreed about the washers, if need be lots of material options there, IMO. Lots of ways to ‘hide’ them too, if desired.
Carbidizing is like adding a carbide washer…again, not sure how much sense that makes.

-
It's fascinating stuff. The SAK I have with Ti liners isn't carbized. No problems with galling or things getting sticky, but that's anecdotal evidence. Other folks mileage may vary.
I prefer brass liners, tho.
-
@Singh said:
It's fascinating stuff. The SAK I have with Ti liners isn't carbized. No problems with galling or things getting sticky, but that's anecdotal evidence. Other folks mileage may vary.Sounds like another one of those ‘overblown issues on the internet’ kind of thing stemming from some other issue as I suggested. ‘Improper’ tool finishing can easily cause such issues. So can operating a knife un or underlubricated.
I prefer brass liners, tho.
Nickel silver for me. But I wouldn’t discourage the use of Ti because of that. Like I don’t get anyones preference for brass aside from cost saving. But I wouldn’t discourage anyone from using it. I’d never even stock any brass sheet, unless paid well to do it.

-
Nickel sIlver is a great liner but it wasn't an option on my 91mm SAK mod. shrugs
back on topic: I don't think we (well, certainly me!) have any answers for the OP.
-

I suppose I only had suggestions. 1. Do it. 2. Cut the slot with a radial cut not a full face.
I’d add fire/safety precautions milling Ti for the first time. Bucket of sand at the very least.
I did end up getting some Ti sheet for liners. And it’s not that hard to cut…even with hand tools. The plan is to drill/cut holes needed much the same way I do nickel silver. By hand with sharp tooling. I sharpen and resharpen most of my own stuff including the carbide and drill bits. Just gotta know what ‘works’ for hand work. Requirements aren’t the same for a bit used in a mill. I rarely break bits and my stuff lasts a long time for what I do. Not really expecting it to be much different because I’m not working with a mill and shouldn’t have the same concerns the OP has on feed rates and the hazard of overheating the tooling.
-
Cutting the thinner stock for liners and spacers turned out to be easy enough with hand tools that I got some other thicknesses up to 3mm. In theory, the thicker materials should be easier to cut (able to use coarser cutters/blades, but maybe a bit tougher to drill.
-
Not a myth or a way to generate more funds. Titanium is actually a softer metal, at least what most of us use, which is a alloy. Here’s some real info on the subject.
Titanium Alloys - Wear Resistance
The wear resistance of titanium alloys is quite poor. It can be enhanced by any number of surface treatments such as enhanced surface films, conversion coatings, electrolytic and electroless plating, thermal spraying, nitriding and shot peening. These processes are reviewed for titanium herein.
AZoM (www.azom.com)
And most real knife makers don’t carbidize they use washers or bearings. If you don’t believe anyone take two pieces and rub them together with a little force. Titanium is “gummy” with lack of a better word.
-
Not sure if that’s info for the OP gone MIA?
But yes, actually many common knife materials have issues when un or under-lubricated. Stainless on stainless has a huge coefficient of friction dry. Even when highly polished. But nobody makes a big deal about it and we all know to oil our knives. So unless there’s some other unknown about stainless and titanium interactions, I don’t think any of this side discussion relates much to the machining, cutting or shaping titanium.

Seems like there’s enough myth and mystery about working with it.
I recently got an alox scaled knife that’s over 50 years old. Good shape but locked up pretty bad. Just needed a good lube and operation to work all or enough of the oxides out for proper operation and snap. Care was only needed to prevent the aluminum oxide from marring the stainless while dry. Because that is a material that’s significantly harder than SAK stainless.
Is anyone claiming that lubrication doesn’t fix or prevent galling issues between Ti alloys and stainless?
-
Just to make the point…even this ragged old SAK metal saw from 1958 is capable of cutting grade 5 titanium. Just used to notch these marks, but Ti isn’t hard as many seem to think.



-
True. I say it’s more like aluminum “gummy”. But I don’t have any pure Ti to test. That stuff is expensive for pure. Nope not me lol
-
Hi, I'm back :)
I set up my mill with a mist coolant system, and a vacuum duct to suck it up so it wouldn't make a mess. That took a while, but it's working well; when I get done cutting, the tool is still cool.I've been experimenting with 7075-T6 and did some tests; this is my first attempt at machining titanium.
This is the first step: I have managed to drill and countersink the screw holes, and cut out the outline of the scales, and radius the edges. I have the tool slots programmed, but I haven't cut them as yet, that's the next step.
[attach id=0 msg=2335593]
This still isn't quite right as the screw holes are not coming out clean, but I'll make some adjustments.
-
Nice progress.

-
Looking good :) What kind of milling machine do you use? Any special titanium tools or cutters?
-
Hi Vidar
I am machining on what is mostly a Sherline 2000; although the differences (between mine and a stock model 2000) are for increased work envelope and don't affect these nice and small pieces.
I'm using carbide endmills, TiAlN or AlTiN.The parts that cut properly were a 1/4" 2 flute, and a 3 flute 1/8" radius endmill.
The screw holes were cut with an uncoated endmill, but I don't really think the problem was because of the lack of coating. -
Interesting.
I have't milled titanium as there has never been a use for that around here. Is it a bit gummy like aluminium or more steel like?
-
Well... I gotta say, I used the same G-code on the titanium there, that I used successfully on the 7075; and the screw holes came out the correct size in the aluminum; but they are undersize here.
So; ya, titanium, living up to its reputation.
I have a couple of ideas to try. -
Progress update: worked out the screw holes.
Not much progress, but some.Haven't cut the tool slots yet.
Pretty well decided to use standard-factory size pivot pins all the way around; with ... probably only one of the ones in the middle with a M1.6 screw in it; the other going into blind holes in the scale. Y'know, like ... everybody else

This one in this picture is drilled out with 2.5mm pivot pins and M2 screws all around.

-
Nice job, looks awesome !

-
Wow, that looks neat! Keep us posted

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login