PST, PST II Owners Club
-
I like the Wharncliffe blade, too. -
The PST I got from a thrift store a few months ago. It's been given a quick cleanup, but I plan to do some more intensive cleaning and modification at some point, including cutting down the snapped plier tips, and replacing the knurled screws with hex or something.
Date codes: 0395/0295




-
Seems that this PST has been in for warranty work at some point
the reason I say this is that the blade seems to be from an older PST than what 1995 PST should have 
Looks great and what do you have planned for it

-
@Poncho65 said:
Seems that this PST has been in for warranty work at some point
the reason I sat this is that the blade seems to be from an older PST than what 1995 PST should have 
Looks great and what do you have planned for it

Going to cut the plier jaws down so they're actually in line, as right now they're almost completely useless (see attachment for a better shot of the damage), swap the screws (or be lazy and cut a slot into them so i can just use a screwdriver), 3d print some kind of coloured "scales" and either a clip or an expanded lanyard hole, maybe swap some tools, maaaaaybe expand the recess for the nail nicks for easier folding out. Not sure what else to do as of yet, but given that I'm fairly sure it has no collector value, I want to use it as a platform for basically anything I think of.

-
Can't wait to see what you come up with

-
Hi folks, got a few PST questions:
- Took the thing completely apart to clean the heck out of it and I noticed that the blade half didn't have washers like the file half, which had two. Was the blade half supposed to have two washers as well? Do you think it would be worth it to replace them with phosphor bronze?
- I want to try 3d printing a bit holder for the leatherman flat bits, but I don't have any dimensions. I know they're similar to 1/4" bits but cut down, but does anyone have the thin dimension that was cut? I want to try printing it and seeing how well I can get the tolerances before I buy bits.
- The blade tip is bent, any tips for bending it back nicely?
- Does anyone have any leads on replacement pivot screws with proper drives? Hex is best, but robertson or philips/jis/whatever is fine too.
- does anyone know what steel the handles are made of? I'm considering some kind of refinishing or engraving or something.
-
Welcome the

First question you can put washers by the blade same as the file and it maybe should have already had at least 1 by it
if the bronze washers are thin enough then yes it would be fine 
A 3D Printed bit holder would be awesome but I don't know the dimensions of those bits

As for question 3, you can try to bend it but there is always the chance (and a very good chance unfortunately) that it will snap off instead of bend :ahhh so do that at your own risk :ahhh
No idea about different pivots unfortunately but perhaps someone will come along that does know

Thw handles are likely just 420 stainless and although tough, they can be engraved
files will also be able to be used and can cut grooves in them 
I hope I was some help

-
Great pic, Steve

-
Thanks !

-
Hi all. I got a PST II from the antique store last weekend and cleaned it up alright but the k ife blade doesn't have much for "walk and talk", as in it stays open mostly but is very easy to close. Any suggestions on fixing this? I guess it's kind of a non issue if I use it with the handles closes but figured I'd ask anyway. Thanks a lot.
-
@Jedula said:
Hi all. I got a PST II from the antique store last weekend and cleaned it up alright but the knife blade doesn't have much for "walk and talk", as in it stays open mostly but is very easy to close. Any suggestions on fixing this? I guess it's kind of a non issue if I use it with the handles closes but figured I'd ask anyway. Thanks a lot.G'Day,
Congrats on an excellent Leatherman, one of my favourites. Is it just the knife blade that is loose, or all the tools on that pivot? It may be a pivot bolt that needs some tightening. Post a pic or two and it may be easier to help with a fix. If it is the pivot bolt, you may need to invest in some Leatherman specific tools from one of our inmates. Two small pliers with fine teeth can be used in a pinch, but it may mark / damage the pivots.
Cheers, Pete
-
with pieter 
Welcome back to
and congrats on getting a PST II, Jedula

-
Thanks guys, I took it apart to clean and the pivot is tight with no side to side movement. Just the knife seems to not want to be held open by the spring properly. I can't seem to figure out adding pictures for some reason.
-
The pics have to be under 512kb or you can upload to a photo sharing site like Imgur and put the pic link

Could possibly be a deformed area on the knife causing it not to engage properly

-
Think I figured out the pictures. Here we go.
.jpg)
.jpg)
.jpg)
.jpg)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
