Knipex Owners Club
-
+3
I'm gonna steal this idea
looks a lot better than mine that uses friction-based retention

-
The 125 Cobra pliers came in handy earlier today. I helped someone who was locked out of a house. I used the Cobras to undo a bolt that the chain was attached to on the door to get it loose.
-
That one has been tempting me for some time, mostly due to its sheepsfoot and not spear point blade.
The only problem I have is the handles. Whoever makes these in Solingen for Knipex has also produced versions for Hilti (which has a bottle opener) and Stahwille, among others. The handles on mine (the Hilti Tea Time) have started to come off. They're attached much like an SAK but aren't able to simply snap back on. I presume the design was updated, as I have seen others with different scales.
-
Today is actually the first day I have used it. Based on this limited usage, I found it to be a good, but not necessarily great, knife.
I loved my Edgeforce from the start, no doubt in part due to the pocket clip and OHO sheepsfoot as well as being the perfect size for the work I do. I haven't fallen in the same way for the Knipex. Mostly, I find it to be a little too large. However, the larger size may be great for other types of use.
Hopefully the handles are attached better than they were on your Hilti.
-
Have a few knipex tools. These ones are edc. Gave the 125s away to a friend when I got these kind of regret it now

-
It looks like my 125mm pliers Wrench acquired some rust. What would be the best way to take care of it?
-
@ToolJoe said:
It looks like my 125mm pliers Wrench acquired some rust. What would be the best way to take care of it?If it’s only a little surface rust, I would say try to keep the tool dry and wiped down with a bit of oil as much as possible, and otherwise don’t worry about it. I have some tools from my grandfather that are a number of decades old, and many have some surface rust from being kept in a garage or shed, but they all work just fine.
If yours is rusted so badly that its functioning is impacted, and or it will frequently be exposed to moisture or high humidity, perhaps consider replacing with the chrome-plated version?
-
@ToolJoe said:
It looks like my 125mm pliers Wrench acquired some rust. What would be the best way to take care of it?I use a quick spray and wipe with CRC 6-66 Marine to remove light surface rust.
And if it has become wet I do the same before storage of any blackened tools or anything of cast iron.
-
My knipex xs have a small a amount of surface rust but it’s mainly off being used in plumbing I do keep it wiped down with oil but it’s a tool at the end of the day
-
This setup punches well above its weight…


-
- [attach id=0 msg=2392012]

-
Been using 125 cobras at work for a couple of weeks. When I first got them, I thought they were too small to be useful and a bit of a novelty, but I've been finding then very useful. Really like carrying as a combo with a SAK. Would be awesome if Knipex could somehow add wire cutters to the small cobras.

-
When I see these pliers with a SAK its clear how small they are. I'd imagine they are robust and great for jobs on the spot.
-
I usually carry these two as a set.

I mostly use my Cobras for fasteners and pulling nails (as well as anything I'd normally use Channellocks on). The 140mm Combination Pliers are for basic pliers tasks--bending and twisting wire, as well as cutting wire. They can also hold the other end of a fastener when a MT is not on hand. Coupled with a needlenose multitool (and or SAK) and the Pocketwrench II, I think I'm pretty well set for basically anything.
I've handled rusted and damaged water hose fittings, rusted/damaged bolts (up to 9/16), and removed stripped screws with the 125mm Cobras, and I prefer to affix T-posts to the fence with shorter pliers. The 140mm Combination Pliers have cut and twisted all sorts of soft and hard wire, and have been used on nuts in a pinch. These are "real tools for real jobs" without being an absolute brick in the pocket.
Knipex was the only company who had small pliers that did the job. The smallest Channellocks are about the same size, but don't open up much at all, and are very dainty. The closest models that open up as much as the 125mm Cobra are about 8 inches long--NOT pocketable. Little "toolkit" pliers are few and far between. I had tried a pair of vintage Elliot Lucas pliers from like the '60s, but they were shot, same with a '80s Crescent pair my Granddad gave me. I tried the 160mm model first, only to find them bulky and heavy (they eventually went in my fencing stuff), and then found the 140mm were just as capable, at half the weight.
-
Got these 2 a couple of weeks ago.

-
A few new things I got the past few months.


Tools fit nicely into cutlery trays. And if you're lucky enough the tray will fit into a tool cabinet drawer.


-
Excellent collection RP

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

