Knipex Owners Club
-
@ToolJoe said:
It looks like my 125mm pliers Wrench acquired some rust. What would be the best way to take care of it?I use a quick spray and wipe with CRC 6-66 Marine to remove light surface rust.
And if it has become wet I do the same before storage of any blackened tools or anything of cast iron.
-
My knipex xs have a small a amount of surface rust but it’s mainly off being used in plumbing I do keep it wiped down with oil but it’s a tool at the end of the day
-
This setup punches well above its weight…


-
- [attach id=0 msg=2392012]

-
Been using 125 cobras at work for a couple of weeks. When I first got them, I thought they were too small to be useful and a bit of a novelty, but I've been finding then very useful. Really like carrying as a combo with a SAK. Would be awesome if Knipex could somehow add wire cutters to the small cobras.

-
When I see these pliers with a SAK its clear how small they are. I'd imagine they are robust and great for jobs on the spot.
-
I usually carry these two as a set.

I mostly use my Cobras for fasteners and pulling nails (as well as anything I'd normally use Channellocks on). The 140mm Combination Pliers are for basic pliers tasks--bending and twisting wire, as well as cutting wire. They can also hold the other end of a fastener when a MT is not on hand. Coupled with a needlenose multitool (and or SAK) and the Pocketwrench II, I think I'm pretty well set for basically anything.
I've handled rusted and damaged water hose fittings, rusted/damaged bolts (up to 9/16), and removed stripped screws with the 125mm Cobras, and I prefer to affix T-posts to the fence with shorter pliers. The 140mm Combination Pliers have cut and twisted all sorts of soft and hard wire, and have been used on nuts in a pinch. These are "real tools for real jobs" without being an absolute brick in the pocket.
Knipex was the only company who had small pliers that did the job. The smallest Channellocks are about the same size, but don't open up much at all, and are very dainty. The closest models that open up as much as the 125mm Cobra are about 8 inches long--NOT pocketable. Little "toolkit" pliers are few and far between. I had tried a pair of vintage Elliot Lucas pliers from like the '60s, but they were shot, same with a '80s Crescent pair my Granddad gave me. I tried the 160mm model first, only to find them bulky and heavy (they eventually went in my fencing stuff), and then found the 140mm were just as capable, at half the weight.
-
Got these 2 a couple of weeks ago.

-
A few new things I got the past few months.


Tools fit nicely into cutlery trays. And if you're lucky enough the tray will fit into a tool cabinet drawer.


-
Excellent collection RP

-
I got the 180mm aka 7" Cobra and Pliers Wrench.

This means that I have all Cobras up to 250mm, and all Pliers Wrenches up to 250mm except the 100mm one. :ahhh
This means that I have no self control.
This also means that I have to get the 100mm Pliers Wrench. :D
-
@ReamerPunch said:
.......This also means that I have to get the 100mm Pliers Wrench. :D:D
-
@ReamerPunch said:
and all Pliers Wrenches up to 250mm except the 100mm one. :ahhhWhat about the XS Pliers Wrench?


-
@ReamerPunch said:
I got the 180mm aka 7" Cobra and Pliers Wrench.
This means that I have all Cobras up to 250mm, and all Pliers Wrenches up to 250mm except the 100mm one. :ahhh
This means that I have no self control.
This also means that I have to get the 100mm Pliers Wrench. :DYes!

-
@powernoodle said:
What about the XS Pliers Wrench?


You're not helping! :ahhh
Must.....resist......
But awwwwww, look how cute it is!
-
Trying to resist as well, pretty hard

-
@ReamerPunch said:
I got the 180mm aka 7" Cobra and Pliers Wrench.
This means that I have all Cobras up to 250mm, and all Pliers Wrenches up to 250mm except the 100mm one. :ahhh
This means that I have no self control.
This also means that I have to get the 100mm Pliers Wrench. :DHow about the black and silver versions? And the handle variations?
-
Some 1980s Knipex stuff
After seeing all your new and shiny Knipexes here I thought a few pics of my old Knipex tools from the '80s be interesting.
All made before the wall went down so marked as Made in W.Germany.
Mostly electrician related pliers with insulated handles. They looked like strawberry jelly back then :D





These bit the flash once :ahhh

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
