Gerber Crucial
-
It has an anvil style like on the rest of the gerber line (well most of it), they work pretty good and cut paper. I thought only my leatherman's were this good in regards to cutters but I was wrong

-
I don't understand why Gerber didn't put serrations on tips of the pliers... ::) That's like buying tires without treads!!!
-
-
you could remove it, it's not optioned for tip up or tip down transfer. It's only tip down and it is attached with three T6 screws.
-
The Gerber Crucial review is now posted on the main site.
-
-
-
-
-
Welcome back Dave!

Crucial blade length is exactly 60mm from handle to tip. (2-3/8" for us unmetricated folks)

-
-
Sorry, somehow I missed the question about blade length. Thanks Bob for answering that for me!

-
@J-sews said:
Welcome back Dave!
Crucial blade length is exactly 60mm from handle to tip. (2-3/8" for us unmetricated folks)

Hi Bob, so they made a decent shaped blade then made it even shorter than the LM Skeleton! As most places that have a blade limit seem to have settled on 3" they could hyave easily put another 10mm to 15mm on the blade and given it a useful and legal blade. Apart from the bottle opener/carabina it was the blade length on the Skeleton that stopped me ggoing for it. Oh and the daft dedicated screwdriver bits.
Ah well I guess I will stay with the old Recoil that is doing sterling service even after being dropped then ran over with a van! With the Paul Chen clip it is easier to carry than the other tools I have.
I bet the carabina is whipped off and replaced with a file or something useful by some MODer, I know that is what I intended doing.Davet
-
Ahh, very good idea sir!
And the carabiner on the Crucial is a bit thick too, so I'll bet a clever person could get two blades in it's place. 
-
-
Ahh, very good idea sir!
And the carabiner on the Crucial is a bit thick too, so I'll bet a clever person could get two blades in it's place. 
How about one pair of scissors in place of the carabiner?
.
Hmmm, I don't see why not. There's plenty of space width-wise, just not a lot of length. But scissors from another Gerber tool should fit fine. (assuming the pivot pins are the same diameter)
Another nice thing about the Crucial is it's all assembled with torx screws, so it should be easy to take apart and find out.

-
@J-sews said:
Ahh, very good idea sir!
And the carabiner on the Crucial is a bit thick too, so I'll bet a clever person could get two blades in it's place. 
Rather disappointed to find the carabiner does not lock so any other tool you try to fit in there is going to flap about. What I have decided to do is remove the thumb stud and attach a stud straight through so it can then open either hand or cut the carabiner off at the bottom and at the top just after the second rivet hole in the blade and pin both the blade and whats left of the carabiner (might need a spacer) to use the carabiner left over as a thumb stud just for me (left handed). If you see what I mean. ??? If I end up with the first option I will just make a washer out of the cut down carabiner.
Dave
Just an after thought any one who thinks the Crucial is a copy of the Skelitool, its the only choice if you want to use standard bits and have a tool that looks like a knife but has the ability of holding and picking things up. It also looks like a knife when closed the Skelitool looks like a small ornimental multitool however you look at it. In fact its nearest rival for me would be the Buck X-tract but although the blade is that bit better the plastic scales put me off.
The other daftd thing I think Gerber have done is produce 2 versions with just a colour difference I would have bought both if one had a straight edge and the other a serated. -
I like it, I don't use it as much as the skeletool. Yes I do think it's a rip off of the skeletool I think though it's hard to make a minimalistic tool and have it not look like the skeletool. Yes the pliers are weak compared to the skeletool and the carabineer on the skeletool is better designed and oriented than on the crucial. I do think Gerber really did try with this one and I give them credit, it's not perfect but it's a pretty good tool. If I had the will power I would put the pliers on the crucial and on the x-tract and pin them against each other, wonder who would win. The blade steel on the x-tract is better, Buck's heat treatment is always great and I am sure the 420HC they use is better than Gerber's mystery steel. The crucial can use Gerber's proprietary bit adapter to use regular bits, not easily but it can. I really like the crucial, just wish it was a stronger tool.
-
That's a good, honest post David!
I wouldn't buy the Crucial as it's not my taste but Gerber really did try.
-
@Leatherman123 said:
That's a good, honest post David!I wouldn't buy the Crucial as it's not my taste but Gerber really did try.
I agree, good posts Dave and Dave.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
