Quality torx screw's?
-
@Mike, Lord of the Spammers! said:
You have REALLY got to go some to break the brass though. :o Anyone ever broke one?
Oh I know, the brass for the hook on the back of 91mm has got a breaking strain of 240 pounds if I remember rightly :)
So why are you worrying then? :D
I know, I know, but if possible I'd like to see if I can go down the steel route before I give up and go with brass :D
-
@Mike, Lord of the Spammers! said:
You have REALLY got to go some to break the brass though. :o Anyone ever broke one?
Oh I know, the brass for the hook on the back of 91mm has got a breaking strain of 240 pounds if I remember rightly :)
So why are you worrying then? :D
me thinks its because Mike doesn't think it looks pretty on alox.
admit it :DThe problem is the end pin on a 93mm are 3mm but the centre pin and the pins for the 91mm SAKs are even smaller.
-
@Mike, Lord of the Spammers! said:
You have REALLY got to go some to break the brass though. :o Anyone ever broke one?
Oh I know, the brass for the hook on the back of 91mm has got a breaking strain of 240 pounds if I remember rightly :)
So why are you worrying then? :D
me thinks its because Mike doesn't think it looks pretty on alox.
admit it :DThe problem is the end pin on a 93mm are 3mm but the centre pin and the pins for the 91mm SAKs are even smaller.
Honestly aesthetics never really concern me where knives are concerned, especially if there users :)
So you'd have to ream out the file and pliers to fit then

-
Yes but its not an issue. Could always but a blob of solder over the ends of the brass pins... make them look prettier for you :P
-
You could use Nickle silver pin stock...that's actually commonly used for slipjoints. I'm thinking of using NS pins the next time I do an Alox mod.
-
@Mike, Lord of the Spammers! said:
@SporkBob NoPants said:
You could use Nickle silver pin stock...that's actually commonly used for slipjoints. I'm thinking of using NS pins the next time I do an Alox mod.
Is it quite workable then?
Yes, not quite as malleable as brass and possibly work hardens faster. It's no problem if you limit the hammer blows.
-
@SporkBob NoPants said:
@Mike, Lord of the Spammers! said:
@SporkBob NoPants said:
You could use Nickle silver pin stock...that's actually commonly used for slipjoints. I'm thinking of using NS pins the next time I do an Alox mod.
Is it quite workable then?
Yes, not quite as malleable as brass and possibly work hardens faster. It's no problem if you limit the hammer blows.
Let us know how you get on then mate

-
I'm pretty certain that the Alox knives use nickle silver pins. I reused the pins from a Farmer to re-assemble my old Electrician.
-
Yes, I only had to peen one side...oriented the factory heads to the front.
-
I saw the suggestion of silver, but why stop there? How about a metal that is "silvery-white in appearance, lustrous, ductile, and malleable. It does not oxidize at any temperature." It also is "well suited for making fine jewelry," and "possesses high resistance to chemical attack, excellent high-temperature characteristics." Sounds perfect right? Well platinum is the metal for you.
-
Not totally on topic: I've been searching high and low for some 4mm pivots like the one in Neil's pic, but to no avail. The plan was to replace the pivot pins of my older Spirit with these to modularize it and, if things turned out ok, then do it to the rest of my Spirits. That would allow for some interesting SOG-like modding and make adding a pocket clip a breeze... :-\
-
@SporkBob NoPants said:
I'm pretty certain that the Alox knives use nickle silver pins. I reused the pins from a Farmer to re-assemble my old Electrician.I'd say you're right, I certainly noticed the difference when doing my Cadet mod.
Mike, I'm afraid to say I've had absolutely no joy in finding any screws small enough for doing SAK mods. Really wanted to try for something modular as well but no luck. :-\
-
I think that a modular SAK cannot be built without a lot of effort and modification.
If you could drill out the tangs smoothly and precisely, you could probably use commonly available pivots. You would then have to have a set of pivots of the correct width for each and every layer combination you want to use.
That doesn't address the problem of the center backspring pivot...there is not enough material there to drill out.
I had the ideal a long time ago of a Hobo knife type arrangement where the knife could be split in half for use and to attach different tool sets...that will happen as soon as I get a lathe and a mill set up in my living room ::)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login