Quality torx screw's?
-
@SporkBob NoPants said:
I'm pretty certain that the Alox knives use nickle silver pins. I reused the pins from a Farmer to re-assemble my old Electrician.I'd say you're right, I certainly noticed the difference when doing my Cadet mod.
Mike, I'm afraid to say I've had absolutely no joy in finding any screws small enough for doing SAK mods. Really wanted to try for something modular as well but no luck. :-\
-
I think that a modular SAK cannot be built without a lot of effort and modification.
If you could drill out the tangs smoothly and precisely, you could probably use commonly available pivots. You would then have to have a set of pivots of the correct width for each and every layer combination you want to use.
That doesn't address the problem of the center backspring pivot...there is not enough material there to drill out.
I had the ideal a long time ago of a Hobo knife type arrangement where the knife could be split in half for use and to attach different tool sets...that will happen as soon as I get a lathe and a mill set up in my living room ::)
-
@ari6126 said:
Would these work?
http://www.fastener-express.com/index.asp?PageAction=VIEWCATS&Category=245Guy's ???
-
Perhaps.
I'm put off by the idea of having a tool that pivots around a set of threads. My worry is that the threads would give up the ghost very quickly. If the P&P isn't much it might well be worth playing with though. -
I've put a 111mm together on threaded bolts before but that was only as part of an experiment not intending to actually use it like that.
I'm not sure of long term viability but in the short term it should work fine. Hmmm

-
@Gareth said:
I'm put off by the idea of having a tool that pivots around a set of threads.That is my first thought too. I discarded that ideal over 15 years ago when I had free access to high-quality Aircraft and Instrument hardware like that. :P
Maybe I should have put one together then to see how it held up...
-
What am I missing here? You don't want a SAK with a couple of big frankenstein bolt-heads sticking out the side do you? ??? And what would the bolts thread into? Big frankenstein nuts on the opposite side??
-
Heeeeelllllooooo! You've taken the dive then have you mate?! Good show!
Can't wait to see how you button her up. :)Tell me though if you will, what diameter were the original pins?
-
Are you going to rivet with stainless rod Neil?....You might need a bigger hammer :D
-
Forget how it's held together, what's the tool line-up? :)
Good job mate I think you are in unknown waters with that one.

-
Heeeeelllllooooo! You've taken the dive then have you mate?! Good show!
Can't wait to see how you button her up. :)Tell me though if you will, what diameter were the original pins?
3.1mm , they're probably some exact imperial measurement but that kind of crazy talk scares me ;)
1/8 inch then. That's good to know (although too damn small to drill and tap like I do the Spirits) :(
I'll throw some potential pin stock in with that package I'm sending you. :)
-
What am I missing here? You don't want a SAK with a couple of big frankenstein bolt-heads sticking out the side do you? ??? And what would the bolts thread into? Big frankenstein nuts on the opposite side??
Like this :D
I hasten to add they're temporary! Its a work in progress.
Looking good Neil
, I would like a nudie Juice too , I am most interested as to what you have changed in that one mate
.Hopefully I will find some nice Torx's fastners to replace LM knurled fasteners.
-
Yeah, the juice looks cool. I didn`t get the sense of elox handles on the juice series anyway. might look nice but scrachtes easier than steel and add to weight and width.
-
What am I missing here? You don't want a SAK with a couple of big frankenstein bolt-heads sticking out the side do you? ??? And what would the bolts thread into? Big frankenstein nuts on the opposite side??
Like this :D
I hasten to add they're temporary! Its a work in progress.
That does look cool. :D
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
