Charge saws
-
4-1/2 is may be long enough. Any longer may be overkill on a 4" long tool.
-
Everything usually takes about a week to come from or go to the US from here. Plus, my mail carrier likes to skip my small street on Fridays so she can go and get drunk sooner. It was probably supposed to be here today, but I likely won't see it till Monday... assuming she doesn't skip my street again because she's hung over.
Def -
OK, I promissed I'd come back and let ya know how it works; GREAT!
I got the blade yesturday, and it works! Locks in solidly, and stays put. I cut about an inch into 3/32" 1095 (non-hardened) blade steel with it with no problems with it moving in the tool. :) :)
The lenth is good, although about an 1/8" storter might be better, as it has a tendancy of sticking me in the finger when I draw the tool. (With it in the "pocket" behind the tool in the nylon sheath.) But it might be harder to get out, if it was shorter. So its something for personal preference, as I see it.
The TPI is nice, and it works for steel, and I tried it on some brass too. But I generaly like more agressive, like, say 18 TPI. But I don't know how easy it would be to use in that short of a stroke. Again, something up to preference.
The important point is, that it works in the new Wave.
I picked up a 12" 18 TPI "bi-metal with cobalt" blade...... I'm going to try cutting a couple from it, now that I have the one for a pattern. One of those carbie grit blades(Remgrit) might be nice to try too.
Thanks again for sending it! its a realy nice adition to my EDC.
Gary
-
I'm glad it's working for you Ice Tigre. Let us know how the 18 tpi blade works, as I have not tried any of those yet.
Regarding the Rem-grit blade, I've only made one of those. (See picture at beginning of this thread.) I sent it off to Def for testing without trying it myself. I'm hoping his mail carrier recovers from her hangover on Monday morning and delivers it to the right address! :D
-
I do manage to get mail some Mondays... I wish I had the kind of job where I could only do what I feel like doing and have the union insist on regular and frequent pay raises...
Def -
Thanks J-sews just received the saw cant wait to try it.
-
Just found this topic and those saw attachments look awesome. I sent you a PM J-Sews seeking a blade or two..that is if I did it right :) You are dealing with a newbie here on forums.
-
Greetings Cacherx4, it's always good to hear from a fellow Michigander! :)
(reply sent)
-
I received my blade in the mail today and went right outside to try it out. First impressions were good, it fit snuggly into the lanyard ring/belt clip receptacle with no wobble. I tried to cut some metal fencing about 2" diameter but found it difficult due to the short blade size. This really isn't an issue to me since this type of tool isn't meant to do that IMO!! Next I cut some rusty nails off the garden fence posts...worked GREAT, I also used it to cut some aluminum flashing that was hanging out of my side porch step, I found out on the front porch step it was easier to just score it with my knife and bend it apart than use a sawzall balde :-\ My mistake. Then it was into the garage to cut a 60D galvanized nail in the vise just because I could ;D went thru like a hot knife thru butter once again with no blade wobble.This is definetly a great add-on and I am glad J-Sews has so generously offered some to try out. Thanks alot!!!
Jim

-
Thanks for the feedback Jim!
UPDATE:
So far I've sent blades out to 12 different members, with good results. It appears clear now that the saws work well in New Wave models, so I guess I should have titled this thread "Wave/Charge Saws." The first ones sent out measured from 4-1/4" to 4-1/2" long, but feedback I got suggested a shorter length to keep the blade ends from sticking out of the sheath while carried. Second batch of blades onward have been 4" long. All of the blades sent out before this week have been fine-cut 24 teeth-per-inch. Cacherx4 got a medium-cut 18 tpi, which sounds like it worked well for him. Contact me if you'd like to try one of these.In addition to those sent to MT.org members, I sent one sample blade to Leatherman Tool Group per their request. It was received last week, and is "being evaluated by their design engineers." I'll keep you folks advised when I hear more.
~Bob
-
J-sews finally got a chance to put it on my Charge. A miniscule wobble side to side due to the thickness of the saw, however; up and down is perfectly solid, an excellent design on your part. It's part of my animal rescue gear now I'm not going to waste it on ordinary chores so I'll let you know how it performs on the next rescue I need it. Thanks again.
-
Thanks to CacherX4, I've got a couple more of these to give away. They are the Piranha 18 tpi blades that were pictured a bit earlier in this thread. Thanks Jim!
Anybody interested?
-
Oh, Oh, can I get one :) LOL No problem, thank YOU!!!
-
I made up another batch of these yesterday. Lenox brand, 18 teeth per inch. Anybody want one that missed out earlier?
-
Those are pretty cool! One of these days I am going to have to get a Charge to try them out!
Def
-
Welcome to the forum Flash!
Always nice to have a Blue Liner here!
Def
-
What a cool idea!
to bad i,ll have to get a charge first!
more money ::)

could you do something similar for any of the swisstools?
-
The reason why this can be done so relatively easily for the LM charge is that the tool has a slot to fit in the removable lanyard, pocket clip. Bob has altered the saw ends to be able to clip into that slot.
Very clever, and very useful indeed.
-
PM sent Flash, check your messages.
...and welcome! :)
-
Hello all, its my first post so i just want to say what a great forum, looks like i will learn a lot here. I got linked to this thread by j-sews on knife forums after i posted about having seen this mod somewhere but not being able to find it. Are you still able to make these mate? If so i would like several, i can paypal or bank transfer you the costs and postage.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login