First Pliers-Based Multi-Tool?
-
I'm trying to figure out what a good, first pliers-based multi-tool would be. I'm mostly a SAK guy. I don't really see that changing.
But... I think a Leatherman/SOG/Gerber could be both fun and useful. The trouble is that I know nothing about these tools and there seem to be a lot of options out there. It's a little overwhelming.
I would mostly use it for typical home owner/dad stuff. I work in IT and do a lot of work with electronics. I certainly don't expect a pliers-based multi-tool to be my only tool or be the perfect solution to every problem, etc. But as much use as I get out of my collection of SAKs...
Here's the thing though - I associate pliers-based tools with being heavy. I'm very unlikely to carry something regularly that requires a belt pouch/sheath or threatens to bring my pants crashing to the ground. Pocket friendly is a must. Especially since the SAKs aren't going anywhere! I'm looking for a supplement for the typical 91mm SAK, not a replacement.
So what are the options for multi-tools on the smaller, lighter end of the spectrum? Any other advice for a first time buyer?
Thanks!
-
You, my friend, have stumbled onto the right place! Stand by for the tsunami of information headed your way!

-
My first recommendation would be the Leatherman Wave
if you find that it might be a bit heavy then the Leatherman Curl is a nice lighter weight option that still has a lot of the good that the Wave has
both of these have a pocket clip option, the Waves is easily Removable via the lock tab and the Curl has one that is attached by screws 
If you don't care about a one hand opening blade then the Leatherman Rebar is also a great choice
a really nice tool compliment and not very heavy either
just doesn't have a pocket clip option 
Hope you find something you really like and want to carry

-
What are you looking for in your multi, besides light weight? It sounds like you're going to pair this with a SAK. What SAK are you going to carry with it? That will help us pick a model that doesn't replicate the tool set on the SAK.
-
@smiller43147 said:
What are you looking for in your multi, besides light weight? It sounds like you're going to pair this with a SAK. What SAK are you going to carry with it? That will help us pick a model that doesn't replicate the tool set on the SAK.That's a fair question but it's not one with a simple answer!
But I tend towards 2-3 layer models at the most for pocket carry. So the Spartan, Climber, Sportsman, or Recruit. Maybe a Tinker or Super Tinker.
And I always have a Rambler in my 5th jeans pocket.
All that said, I don't necessarily mind a little tool redundancy (and it's likely impossible to avoid). Never hurts to have a back up or different sizes of a particular tool, etc.
-
Leatherman PST

-
Bond. Modern PST and in production. Or a Skeletool if you really want to keep the weight down.
-
Those are both interesting suggestions for very different reasons.
The Bond looks like a traditional Leatherman. Meanwhile, the Skeletool looks like it belongs in the engineering section of a Star Trek ship! (That's not a negative thing for a computer nerd like me...)
-
I’ll second the LM Skeletool, with the further refinement to go with either the CX or RX depending on your preference.
-
The more I look at all these suggestions, the more I'm thinking a pocket clip would be a must for me.
So, non-humongous with pocket clip - Curl, Bond, Skeletool, etc. I like that there's a ratcheting driver attachment that can work with some of the models too. Not that I would be likely to carry one with me but I could tuck it away in a convenient drawer/bag/etc.
-
My thinking on this is evolving as the thread goes on here...

But it occurs to me that the knife blade is probably the least important aspect to me of a multi-tool of this type since I'll virtually always have a SAK on or near me as well. I don't think I've really seen blade-less ones though.
-
There is a bladeless Rebar and there was a bladeless Fuse

The choice gets harder the more options that are considered

I did make my suggestions based more on the home owner/dad stuff comment

The Ratchet Driver is an excellent addition along with a LM bit kit

-
@Poncho65 said:
I did make my suggestions based more on the home owner/dad stuff comment
The Ratchet Driver is an excellent addition along with a LM bit kit

Your suggestion of the Curl is currently winning me over, actually. I'm likely to get much more use out of it in "home owner/dad" mode than I am doing IT work. A lot of that is via software/virtualized these days and when it's not, I've got specialized tools close by.
My main motivation to try out something like a Leatherman is an unplanned need for pliers, etc. My Deluxe Tinker has very nice pliers, for what they are, but they are much more "super tweezers" than they are pliers, really.
Speaking of which, no one has suggested a Gerber, SOG, or.... whatever else there is out there. Is Leatherman the top of the heap when it comes to quality?
-
I’m a fan of lightweight PBMT’s and also usually pair them with a SAK
Obviously this all comes down to personal preference but ultimate lightweight is Skeletool with a very different blade to a SAK, so not redundant IMO.
For something that’s got a bit of everything I like the Rebar and also agree with the suggestion of a Bond or PST, but Rebar gives you that bit more for very little extra weight
A second hand Juice (I like CS4 best) also a great choice

-
It’s already been said but Bond or Skeletool are both good lightweight pliers based tools with a pocket clip and ratchet drive compatibility.
If you are willing to add just a little bit of weight the Wave or Charge bring more to the table and are very good tools.
-
So, I’ve been spending some time researching the great suggestions you all have made and, uh…
I think the question is not which one I should buy. It’s more which one should I buy first. :D
You know, for science reasons.
-
That's the spirit! My suggestion is make a list of the functions you want, or don't want, then search for the multitools that match your listed functions. If you don't need a wood saw, for example, then you can save weight by getting a tool that doesn't have a wood saw.

-
That's a good suggestion.
My requirements for a PBMT are actually pretty minimal. I want good pliers and phillips driver(s) that are better than the average SAK (the SAKs with in-line phillips drivers are fairly large, the 2D phillips/can opener and Tinker-style back phillips have well known limitations, etc.).
Otherwise, I'm not too fussed about what the other tools are. Especially since I don't intend for a PBMT to be the only tool in my pocket or anything.
This flexibility makes decisions easier in some ways, but harder in other ways. For example, how many extra tools (adding to bulk/weight) that I'm not super likely to use do I want to carry around? I'm not sure. I find the Skeletool pretty attractive for its minimalism, but it also has the smallest pliers of any non-keychain tool Leatherman makes. If they were more substantial I would probably buy it... I think.

My other source of some uncertainty is the bit exchanger situation. In some ways that's pretty cool. But... Leatherman (not sure about other brands) uses a proprietary size/shape for their bits. I'm not sure how excited I am about being "stuck" in a non-standard, proprietary system like that. Maybe it's not that big of a deal? I'm new to these tools, so I don't really know. Obviously, some models don't have the bit exchanger, so there's that to consider.
There are other things that are just total "unknowns" for me. Like, whether I want outside opening tools or tools that are only on the inside of the pliers handles. I know that I don't particularly care about one-hand opening stuff one way or the other (I wouldn't use SAKs if I did...). But as far as tools on the inside versus the outside of a tool goes, well, I have no idea!
Don't mind me - I'm just overthinking things as usual!
-
Overthinking things is why we are all here.
As far as the proprietary bits that only matters for the actual exchanger. If you have the regular or ratchet extension you can use regular 1/4” bits.
Still feel like the Bond would be great for you. The combination of solid first gen Pliers and 3D Phillips in a simple package.
-
I recommend Bond or Rebar also Victorinox Spirit is an option but more expensive than Bond/Rebar.
Only Tools Matters
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login