Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Scale Polishing

Scheduled Pinned Locked Moved Swiss Army Knights Forum
7 Posts 1 Posters 1.4k Views
  1. Home
  2. Tool Talk
  3. Swiss Army Knights Forum
  4. Scale Polishing
Scale Polishing
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • MuSAKcian Offline
    MuSAKcian
    Posts: 7
    MuSAKcian Offline
    MuSAKcian
    wrote on last edited by
    Quote Reply

      I've been reading old posts about polishing scratched up cellidor scales and thought I'd give it on an old scratched up Fisherman I inherited from my workplace's Lost & Found. Here are the before and after shots!

      It had quite some scratches and appeared more matte before, but I tried rubbing it against my mousepad untill it has some shine.

      I used wet sandpaper 320>600>800>1200, then Meguiar's Scratch X to buffer and it really brings the shine back to it's glory days!

      I can't seem to remove the tiny scratches though. Is it because I didn't sand enough, or did I use a wrong cloth?
      I used a fuzzy microfiber cloth to buffer the scale.

      Or is it never possible to restore it to its brand new state again?

      Screenshot_20230317-210850918_1.jpg

      1 Reply Last reply
      • BarbaBaba Offline
        BarbaBaba
        Posts: 77
        BarbaBaba Offline
        BarbaBaba
        wrote on last edited by
        #1 Quote Reply

          I usually do it almost the same way you did. I wet sand with 800+1200grit with a erasing gum as a block. Then I polish with boat polish on a rubber cloth. But... The deeper scratches you have left is because you did not sand them off in the first place. I have succefully restored celidor before, using acetone. Acetone will desolve the scale material, so just put a drop on the deep scratch an blow it dry. Do not wipe it. The scale will look melted where the acetone was, and then start sanding again.

          1 Reply Last reply
          • MuSAKcian Offline
            MuSAKcian
            Posts: 7
            MuSAKcian Offline
            MuSAKcian
            wrote on last edited by
            #2 Quote Reply

              @BarbaBaba said:
              I usually do it almost the same way you did. I wet sand with 800+1200grit with a erasing gum as a block. Then I polish with boat polish on a rubber cloth. But... The deeper scratches you have left is because you did not sand them off in the first place. I have succefully restored celidor before, using acetone. Acetone will desolve the scale material, so just put a drop on the deep scratch an blow it dry. Do not wipe it. The scale will look melted where the acetone was, and then start sanding again.

              Thanks for the tip BarbaBaba!

              Ah so I actually need to put in a lot more sanding then! It always looked as if it's smooth enough between sanding.

              Would isopropyl alcohol yield the same results too?

              1 Reply Last reply
              • BarbaBaba Offline
                BarbaBaba
                Posts: 77
                BarbaBaba Offline
                BarbaBaba
                wrote on last edited by
                #3 Quote Reply

                  @MuSAKcian said:
                  Thanks for the tip BarbaBaba!

                  Ah so I actually need to put in a lot more sanding then! It always looked as if it's smooth enough between sanding.

                  Would isopropyl alcohol yield the same results too?

                  I am not sure about the alcohol, but it might. Just be careful so you don´t melt them ;)

                  1 Reply Last reply
                  • Farmer X Offline
                    Farmer X
                    Posts: 13,847
                    Farmer X Offline
                    Farmer X
                    wrote on last edited by
                    #4 Quote Reply

                      A very nice polish job! :tu: As for the alcohol, I think I've gotten it on Cellidor with no adverse effects. Maybe I'll leave some old scales in alcohol for a while and see what happens.

                      1 Reply Last reply
                      • Andrew Offline
                        Andrew
                        Posts: 31
                        Andrew Offline
                        Andrew
                        wrote on last edited by
                        #5 Quote Reply

                          Sometimes I use alcool to clean the knifes and it leaves marks on the scales. I usually use a cloth or a piece of paper to polish the scales and they are like new

                          1 Reply Last reply
                          • Buzzbait Offline
                            Buzzbait
                            Posts: 1,068
                            Buzzbait Offline
                            Buzzbait
                            wrote on last edited by
                            #6 Quote Reply

                              Isopropyl alcohol does not play nicely with cellidor scales, in my personal experience. The higher the concentration, the more quickly it degrades the scales.

                              1 Reply Last reply

                              Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                              Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                              With your input, this post could be even better 💗

                              Register Login

                              1. Home
                              2. Tool Talk
                              3. Swiss Army Knights Forum
                              4. Scale Polishing
                              Reply
                              • Reply as topic
                              Log in to reply
                              COMMUNITY LINKS
                              EDC-TV SAKWiki GearFeed SAKSelector
                              Operational Funds

                              Help us keep the Unworkable working!

                              Make A Donation
                              November Goal: $300.00
                              Due Date: Nov 30
                              Total Receipts: $0.00
                              Below Goal: $300.00
                              0% funded
                              • Login

                              • Don't have an account? Register

                              • Login or register to search.
                              • First post
                                Last post
                              0