Showcase: Mods to plier-based multitools
-
@s_a_c said:
Tool Name: Gerber MP600 Drive
Basis: Gerber MP600ST (Sight Tool)
Aim: Create a MP600 with a bit driver, scissors, and the tool layout of my choice. Much prefer the MP600ST as the main tool due to the frame already having cutouts, longer combo knife blade, longer Phillips driver, replaceable cutter inserts, and better plastic tool locks on this model.Mods:
- Removed AR sight tool and add gerber armbar slim bit driver. Driver tool and MP600 crane both had to be modded a good bit to allow fitment. Still need to finish fine tuning, pics are from test fitment. NOTE: attempted to modify the AR sight tool initially to accept a bit extension but this is not recommended as it is easier to add the bit driver from the armbar, and also allows for another short tool to be added.
- Added scissors, Tshank adapter (for surge file, Tshank saw blades, etc), and large flathead with V notch.
- HSS cutter inserts are on the way to replace the absolute garbage carbide inserts.
- EPI insta-black 370SS sample kit on the way to blacken the modified portion of the frame, bit driver, and satin tools.
Also may add Wire Stripper tool from SOG powerlock in near future. I’ve already done this mod to my other MP600.
Sent from my iPhone using Tapatalk
Very nice job, I think from now on every MP600 issued by Gerber should be like this!
-
Tool Name: MP460
Basis: Gerber MP400
Aim: Pack in more tools!... and by taking out any knife blades or awls, make it potentially travel safe. This also fits well with a multi-tool + dedicated folder carry style.
Mods:- File from an MP600 instead of a blade (long slot)
- U-Shank holder in place of the scissors (long slot)
- Removed material from the plier head on the opposite side of the long slots, to allow for semi-long implements:
- moved the scissors to the other end of the stack
- added a thinner, longer cross driver from an original Suspension.
- Shortened the plier head tip and lengthened the sliding grooves slightly to allow the pliers to sit fully inside for more friendly pocket carry and to save a little weight.
- Not shown in the pictures, I replaced the original u-shank RemGrit blade with a 14T metal cobalt steel saw which is pretty versatile and I angled the tip into a chisel/scraper.
Links:


-
Tool Name: Spirit XNP (near perfect)
Basis: Victorinox Spirit X
Aim: Take a nearly perfect tool and make it even closer to perfect!
Mods:- Removed material from the side of the frame & add a slot in the knife blade so that it can be one hand opening. I also removed a small amount of material from near the pivot so the blade will open more easily.
- Did the same thing on the other side so the scissors can be opened one handed. Instead of a hole in the scissors, I just removed a little bit of material to help with friction.
- Removed material from the scissors so they aren't so restricted and I also took off a small amount of metal where the blades meet to form a chamfer in hopes that this would allow material to pass by more easily.
- Modified the can opener by making the 'blade' a continuous shape which is excellent for prying tight things like watch bezels or SAK scales and for carving spoons.
- Modified the inside part of the can opener to be a gutter/pull cutter.
- I guess it is a mod... I bought and added a pocket clip.
It is worth noting that the tool also lost 2 grams in the process and unfortunately gathered a bunch of small metal shavings between the tools. I'm still working them out. This was a bittersweet project because I now have a tool that may just be the pinnacle of all my multitools. Will this be the elusive 'goal' that will end my modding?
Links:



-

Especially the package opener/puller mod on the can opener.
Just a question: have you noticed any increased flexing in the handles or knife blade? I imagine these might have become a tad less rigid due to the removal of material...
-
Thanks! Yeah, I've done the same mod to many can openers of similar style because I find myself using the changes often. I wish they came that way! I haven't yet pushed it super hard since the mod, but in what I have done, I haven't noticed any more flexing than in my stock one. I imagine especially in the blade the force needed to break it has decreased, but I don't usually have to push this knife hard since there are so many other tools for prying and working with hard materials. The material removed from the handles is quite far to the end of the handle and only half way on one side, so that's not something I'm worried about.
One more update, I gave the outside a brushed finish instead of full on polish.

-
Wow this is a very nice mod, Victorinox should really take some inspirations from your work. I didn't like how they've made the one hand opening blade on the new Swisstool, I personally found this "bended tongue" atrociouly hideous (just my personal opinion, don't lambast me please). Overall your small quality of life improvements are worth it!

-
@ModificatYon said:
Wow this is a very nice mod, Victorinox should really take some inspirations from your work. I didn't like how they've made the one hand opening blade on the new Swisstool, I personally found this "bended tongue" atrociouly hideous (just my personal opinion, don't lambast me please). Overall your small quality of life improvements are worth it!
Thanks! Now that I've worked out the metal dust and my fingers have gotten used to opening it, I am very pleased!
-
<u>Tool Name</u>: Bushcraft Charge
<u>Basis</u>: Orange G10 Charge+
<u>Aim</u>: Optimize for Bushcraft & EDC Carry
<u>Standard Tools</u>: Pliers, S30V Blade, Saw, and Bit Exchanger
<u>Outside Mods</u>: I slide a set of Sharpened Tweezers from a Victorinox in between the Saw and tool frame that nests perfectly in the nick of the Saw. Replaced the Serrated Blade with 91mm Victorinox Scissors and filed down the end of the file to 90° so it can be used as a Large Flathead/Scraping tool.
<u>Inside Mods</u>: Replaced the Charge Scissors with a Rebar Awl that’s been shaped to a sharper point to more easily pierce leather and bore holes in wood. Moved the Large Flat Head to the middle tool slot, shortened it to fit with the plier stop, and added a Chisel Edge. In the Large Flat Head's place, I added a Small Flat Head from a Rebar that’s been shaped to fit in tighter/hard to reach places that my bits can't reach (specifically to use on some specific snowboarding edge sharpening tools). On the other side, I used a Dremel to create a hook blade/spoon gouge.
<u>Extended Tools From Bit Exchanger</u>: The Bit Exchanger is the most versatile tool on the Charge+. I replaced the standard combo Phillips/Flathead bit with a brand new #1/#2 Phillips bit for better bit/screw contact when I need a Phillips. When I’m in the city, I carry the Leatherman Ratchet Driver & 711 Ratchet with the 77781 & 77782 Double Sided WiHa Bits. When I’m in the mountains, I carry the Leatherman Ratchet Driver with Stubby 1/4” Drill Bits that make bushcrafting and building with wood much more efficient.


-
I realized that the pictures of the inside tools were very poor quality due to downsizing. Hopefully this shows them a bit better.
[attach id=0 msg=2412037] [attach id=1 msg=2412037]
@GoBlue93 said:
<u>Tool Name</u>: Bushcraft Charge
<u>Basis</u>: Orange G10 Charge+
<u>Aim</u>: Optimize for Bushcraft & EDC Carry
<u>Standard Tools</u>: Pliers, S30V Blade, Saw, and Bit Exchanger
<u>Outside Mods</u>: I slide a set of Sharpened Tweezers from a Victorinox in between the Saw and tool frame that nests perfectly in the nick of the Saw. Replaced the Serrated Blade with 91mm Victorinox Scissors and filed down the end of the file to 90° so it can be used as a Large Flathead/Scraping tool.
<u>Inside Mods</u>: Replaced the Charge Scissors with a Rebar Awl that’s been shaped to a sharper point to more easily pierce leather and bore holes in wood. Moved the Large Flat Head to the middle tool slot, shortened it to fit with the plier stop, and added a Chisel Edge. In the Large Flat Head's place, I added a Small Flat Head from a Rebar that’s been shaped to fit in tighter/hard to reach places that my bits can't reach (specifically to use on some specific snowboarding edge sharpening tools). On the other side, I used a Dremel to create a hook blade/spoon gouge.
<u>Extended Tools From Bit Exchanger</u>: The Bit Exchanger is the most versatile tool on the Charge+. I replaced the standard combo Phillips/Flathead bit with a brand new #1/#2 Phillips bit for better bit/screw contact when I need a Phillips. When I’m in the city, I carry the Leatherman Ratchet Driver & 711 Ratchet with the 77781 & 77782 Double Sided WiHa Bits. When I’m in the mountains, I carry the Leatherman Ratchet Driver with Stubby 1/4” Drill Bits that make bushcrafting and building with wood much more efficient.

-
Excellent mod GoBlue! That looks like it can handle just about anything 👏
-
@customod said:
Thanks! Yeah, I've done the same mod to many can openers of similar style because I find myself using the changes often. I wish they came that way! I haven't yet pushed it super hard since the mod, but in what I have done, I haven't noticed any more flexing than in my stock one. I imagine especially in the blade the force needed to break it has decreased, but I don't usually have to push this knife hard since there are so many other tools for prying and working with hard materials. The material removed from the handles is quite far to the end of the handle and only half way on one side, so that's not something I'm worried about.One more update, I gave the outside a brushed finish instead of full on polish.
Hi,
I wonder, how do you do a brush finish like this? I'm modding a P2 (coming soon exclusively on multitool.org
) and I want to do the same type of finish on it.
Thanks have a good day -
The best way is to first bring it to a polish, but then either way all you need is a scotchbrite pad or similar and use long straight strokes, preferably in a single direction. It is something that I've used a lot when modding watches in the past.
-
@customod said:
The best way is to first bring it to a polish, but then either way all you need is a scotchbrite pad or similar and use long straight strokes, preferably in a single direction. It is something that I've used a lot when modding watches in the past.Thanks for the tip, I'll try it ASAP!
-
Hope we get to see the results in the near future :D -
@customod said:
The best way is to first bring it to a polish, but then either way all you need is a scotchbrite pad or similar and use long straight strokes, preferably in a single direction. It is something that I've used a lot when modding watches in the past.When you say scotchbrite, you talk about this one https://rb.gy/x245q or this one https://rb.gy/qs95r
I'll use some fine sandpaper to polish it, clean it with acetone to remove the grease and then use the scotchbrite. What do you think is it enough?
I'll receive my parts from aliexpress this week, I'll work on it ASAP so I can show you the end result. It won't be a complete overall mod like my Wave, just some twinking to transform my P2 to something more suited for my needs. -
Good way top geht some stuff in the wazoo belt.
Glued some neodym Magnets in
-
I love the belt mod Ledernox! If I used the same belt all the time this would be something I would do for sure! I might do it anyways :D
As for the question earlier about the scotchbrite pad, it is the first link with the green pad that you'd want to use to get the brushed finish.
-
Tool Name: Wave Plus Plus
Basis: Leatherman Wave Plus
Aim: Put everything I want on one EDC multitool
Mods: I don't actually remember what this looked like stock anymore. The dedicated Philips screwdriver is from my Wingman, I ground the Leatherman bit to be a flat blade on one side and I left the 4mm hex on the other, I sharpened the can opener and I moved the various internal tools around. I designed and 3D printed a scalpel holder, a pocket clip, and a comb (the comb goes into the same slot as the saw). I upgraded the main blade to 154CM. Most recently I added the Victorinox scissors from the Huntsman in place of the serrated blade. I added a bit of Dragon Grip tape to help get it out of my pocket.[attach id=0 msg=2418420]
[attach id=1 msg=2418420]

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

