Showcase: Mods to plier-based multitools
-
@ModificatYon said:
Wow this is a very nice mod, Victorinox should really take some inspirations from your work. I didn't like how they've made the one hand opening blade on the new Swisstool, I personally found this "bended tongue" atrociouly hideous (just my personal opinion, don't lambast me please). Overall your small quality of life improvements are worth it!
Thanks! Now that I've worked out the metal dust and my fingers have gotten used to opening it, I am very pleased!
-
-
-
<u>Tool Name</u>: Bushcraft Charge
<u>Basis</u>: Orange G10 Charge+
<u>Aim</u>: Optimize for Bushcraft & EDC Carry
<u>Standard Tools</u>: Pliers, S30V Blade, Saw, and Bit Exchanger
<u>Outside Mods</u>: I slide a set of Sharpened Tweezers from a Victorinox in between the Saw and tool frame that nests perfectly in the nick of the Saw. Replaced the Serrated Blade with 91mm Victorinox Scissors and filed down the end of the file to 90° so it can be used as a Large Flathead/Scraping tool.
<u>Inside Mods</u>: Replaced the Charge Scissors with a Rebar Awl that’s been shaped to a sharper point to more easily pierce leather and bore holes in wood. Moved the Large Flat Head to the middle tool slot, shortened it to fit with the plier stop, and added a Chisel Edge. In the Large Flat Head's place, I added a Small Flat Head from a Rebar that’s been shaped to fit in tighter/hard to reach places that my bits can't reach (specifically to use on some specific snowboarding edge sharpening tools). On the other side, I used a Dremel to create a hook blade/spoon gouge.
<u>Extended Tools From Bit Exchanger</u>: The Bit Exchanger is the most versatile tool on the Charge+. I replaced the standard combo Phillips/Flathead bit with a brand new #1/#2 Phillips bit for better bit/screw contact when I need a Phillips. When I’m in the city, I carry the Leatherman Ratchet Driver & 711 Ratchet with the 77781 & 77782 Double Sided WiHa Bits. When I’m in the mountains, I carry the Leatherman Ratchet Driver with Stubby 1/4” Drill Bits that make bushcrafting and building with wood much more efficient.


-
I realized that the pictures of the inside tools were very poor quality due to downsizing. Hopefully this shows them a bit better.
[attach id=0 msg=2412037] [attach id=1 msg=2412037]
@GoBlue93 said:
<u>Tool Name</u>: Bushcraft Charge
<u>Basis</u>: Orange G10 Charge+
<u>Aim</u>: Optimize for Bushcraft & EDC Carry
<u>Standard Tools</u>: Pliers, S30V Blade, Saw, and Bit Exchanger
<u>Outside Mods</u>: I slide a set of Sharpened Tweezers from a Victorinox in between the Saw and tool frame that nests perfectly in the nick of the Saw. Replaced the Serrated Blade with 91mm Victorinox Scissors and filed down the end of the file to 90° so it can be used as a Large Flathead/Scraping tool.
<u>Inside Mods</u>: Replaced the Charge Scissors with a Rebar Awl that’s been shaped to a sharper point to more easily pierce leather and bore holes in wood. Moved the Large Flat Head to the middle tool slot, shortened it to fit with the plier stop, and added a Chisel Edge. In the Large Flat Head's place, I added a Small Flat Head from a Rebar that’s been shaped to fit in tighter/hard to reach places that my bits can't reach (specifically to use on some specific snowboarding edge sharpening tools). On the other side, I used a Dremel to create a hook blade/spoon gouge.
<u>Extended Tools From Bit Exchanger</u>: The Bit Exchanger is the most versatile tool on the Charge+. I replaced the standard combo Phillips/Flathead bit with a brand new #1/#2 Phillips bit for better bit/screw contact when I need a Phillips. When I’m in the city, I carry the Leatherman Ratchet Driver & 711 Ratchet with the 77781 & 77782 Double Sided WiHa Bits. When I’m in the mountains, I carry the Leatherman Ratchet Driver with Stubby 1/4” Drill Bits that make bushcrafting and building with wood much more efficient.

-
-
@customod said:
Thanks! Yeah, I've done the same mod to many can openers of similar style because I find myself using the changes often. I wish they came that way! I haven't yet pushed it super hard since the mod, but in what I have done, I haven't noticed any more flexing than in my stock one. I imagine especially in the blade the force needed to break it has decreased, but I don't usually have to push this knife hard since there are so many other tools for prying and working with hard materials. The material removed from the handles is quite far to the end of the handle and only half way on one side, so that's not something I'm worried about.One more update, I gave the outside a brushed finish instead of full on polish.
Hi,
I wonder, how do you do a brush finish like this? I'm modding a P2 (coming soon exclusively on multitool.org
) and I want to do the same type of finish on it.
Thanks have a good day -
-
@customod said:
The best way is to first bring it to a polish, but then either way all you need is a scotchbrite pad or similar and use long straight strokes, preferably in a single direction. It is something that I've used a lot when modding watches in the past.Thanks for the tip, I'll try it ASAP!
-
-
@customod said:
The best way is to first bring it to a polish, but then either way all you need is a scotchbrite pad or similar and use long straight strokes, preferably in a single direction. It is something that I've used a lot when modding watches in the past.When you say scotchbrite, you talk about this one https://rb.gy/x245q or this one https://rb.gy/qs95r
I'll use some fine sandpaper to polish it, clean it with acetone to remove the grease and then use the scotchbrite. What do you think is it enough?
I'll receive my parts from aliexpress this week, I'll work on it ASAP so I can show you the end result. It won't be a complete overall mod like my Wave, just some twinking to transform my P2 to something more suited for my needs. -
-
I love the belt mod Ledernox! If I used the same belt all the time this would be something I would do for sure! I might do it anyways

As for the question earlier about the scotchbrite pad, it is the first link with the green pad that you'd want to use to get the brushed finish.
-
Tool Name: Wave Plus Plus
Basis: Leatherman Wave Plus
Aim: Put everything I want on one EDC multitool
Mods: I don't actually remember what this looked like stock anymore. The dedicated Philips screwdriver is from my Wingman, I ground the Leatherman bit to be a flat blade on one side and I left the 4mm hex on the other, I sharpened the can opener and I moved the various internal tools around. I designed and 3D printed a scalpel holder, a pocket clip, and a comb (the comb goes into the same slot as the saw). I upgraded the main blade to 154CM. Most recently I added the Victorinox scissors from the Huntsman in place of the serrated blade. I added a bit of Dragon Grip tape to help get it out of my pocket.[attach id=0 msg=2418420]
[attach id=1 msg=2418420]

-
Great work ThePrinterUnderTheStairs! I’d love to implement a comb into one of my tools. What kind of comb was it, and what did you have to do other than drill a pivot to make it work?
@ThePrinterUnderTheStairs said:
Tool Name: Wave Plus Plus
Basis: Leatherman Wave Plus
Aim: Put everything I want on one EDC multitool
Mods: I don't actually remember what this looked like stock anymore. The dedicated Philips screwdriver is from my Wingman, I ground the Leatherman bit to be a flat blade on one side and I left the 4mm hex on the other, I sharpened the can opener and I moved the various internal tools around. I designed and 3D printed a scalpel holder, a pocket clip, and a comb (the comb goes into the same slot as the saw). I upgraded the main blade to 154CM. Most recently I added the Victorinox scissors from the Huntsman in place of the serrated blade. I added a bit of Dragon Grip tape to help get it out of my pocket.[attach id=0 msg=2418420]
[attach id=1 msg=2418420] -
Thanks GoBlue93!
The comb, pocket clip, and scalpel holder are all designed and 3D printed by me. Images of the 3D models I created are below. Of the three designs, the scalpel holders are the sturdiest, and can be printed out of PLA+, ASA, or Polycarbonate. The comb is printed out of nylon filament and made more flexible by throwing it in boiling water after it's printed. It's reasonably flexible but if you aren't careful with it, it can break, especially on the thinnest part where is goes around the pin (circled in red on the picture). Oh, and the comb tines are only about a quarter inch long, so for me it's a beard/mustache comb. I don't think it would work for the hair on the top of your head unless you have pretty short hair.I've been thinking I might want to send some of these prints to people willing to install them in their knives, field test them a bit, and give feedback. As it stands, I couldn't see ever charging money for the prints. The comb and pocket clip both seem too fragile to me (the part of the pocket clip that keeps breaking is also circled in red), but maybe with some feedback I can improve them. The scalpel holders are tougher, but if someone decides to apply a lot of pressure with the scalpel they would probably also fail (although, it's a scalpel, so applying pressure with it means you are probably using the wrong tool, IMHO). This project would probably warrant its own thread, but for those reading, does this sound like something folks on this forum would be interested in?
[attach id=0 msg=2418572]
[attach id=1 msg=2418572]
[attach id=2 msg=2418572]
[attach id=3 msg=2418572]



-
I would certainly be interested in receiving the files if you are willing to give them out. I've got friends with 3D printers, so I could get them printed myself. The scalpel blade holder seems very helpful.
-
Just catching up on this thread
So many great mods, you all have given me so many ideas :ahhh I haven't done a mod in a while and think I may try my hand at it again 

-
@customod said:
Tool Name: Spirit XNP (near perfect)
Basis: Victorinox Spirit X
Aim: Take a nearly perfect tool and make it even closer to perfect!
Mods:- Removed material from the side of the frame & add a slot in the knife blade so that it can be one hand opening. I also removed a small amount of material from near the pivot so the blade will open more easily.
- Did the same thing on the other side so the scissors can be opened one handed. Instead of a hole in the scissors, I just removed a little bit of material to help with friction.
- Removed material from the scissors so they aren't so restricted and I also took off a small amount of metal where the blades meet to form a chamfer in hopes that this would allow material to pass by more easily.
- Modified the can opener by making the 'blade' a continuous shape which is excellent for prying tight things like watch bezels or SAK scales and for carving spoons.
- Modified the inside part of the can opener to be a gutter/pull cutter.
- I guess it is a mod... I bought and added a pocket clip.
It is worth noting that the tool also lost 2 grams in the process and unfortunately gathered a bunch of small metal shavings between the tools. I'm still working them out. This was a bittersweet project because I now have a tool that may just be the pinnacle of all my multitools. Will this be the elusive 'goal' that will end my modding?
Links:
Where did you source the pocket clip? How does it attach?
Charles.
-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


Hope we get to see the results in the near future 
