Showcase: Mods to plier-based multitools
-
The best way is to first bring it to a polish, but then either way all you need is a scotchbrite pad or similar and use long straight strokes, preferably in a single direction. It is something that I've used a lot when modding watches in the past.
-
@customod said:
The best way is to first bring it to a polish, but then either way all you need is a scotchbrite pad or similar and use long straight strokes, preferably in a single direction. It is something that I've used a lot when modding watches in the past.Thanks for the tip, I'll try it ASAP!
-
Hope we get to see the results in the near future :D -
@customod said:
The best way is to first bring it to a polish, but then either way all you need is a scotchbrite pad or similar and use long straight strokes, preferably in a single direction. It is something that I've used a lot when modding watches in the past.When you say scotchbrite, you talk about this one https://rb.gy/x245q or this one https://rb.gy/qs95r
I'll use some fine sandpaper to polish it, clean it with acetone to remove the grease and then use the scotchbrite. What do you think is it enough?
I'll receive my parts from aliexpress this week, I'll work on it ASAP so I can show you the end result. It won't be a complete overall mod like my Wave, just some twinking to transform my P2 to something more suited for my needs. -
Good way top geht some stuff in the wazoo belt.
Glued some neodym Magnets in
-
I love the belt mod Ledernox! If I used the same belt all the time this would be something I would do for sure! I might do it anyways :D
As for the question earlier about the scotchbrite pad, it is the first link with the green pad that you'd want to use to get the brushed finish.
-
Tool Name: Wave Plus Plus
Basis: Leatherman Wave Plus
Aim: Put everything I want on one EDC multitool
Mods: I don't actually remember what this looked like stock anymore. The dedicated Philips screwdriver is from my Wingman, I ground the Leatherman bit to be a flat blade on one side and I left the 4mm hex on the other, I sharpened the can opener and I moved the various internal tools around. I designed and 3D printed a scalpel holder, a pocket clip, and a comb (the comb goes into the same slot as the saw). I upgraded the main blade to 154CM. Most recently I added the Victorinox scissors from the Huntsman in place of the serrated blade. I added a bit of Dragon Grip tape to help get it out of my pocket.[attach id=0 msg=2418420]
[attach id=1 msg=2418420]

-
Great work ThePrinterUnderTheStairs! I’d love to implement a comb into one of my tools. What kind of comb was it, and what did you have to do other than drill a pivot to make it work?
@ThePrinterUnderTheStairs said:
Tool Name: Wave Plus Plus
Basis: Leatherman Wave Plus
Aim: Put everything I want on one EDC multitool
Mods: I don't actually remember what this looked like stock anymore. The dedicated Philips screwdriver is from my Wingman, I ground the Leatherman bit to be a flat blade on one side and I left the 4mm hex on the other, I sharpened the can opener and I moved the various internal tools around. I designed and 3D printed a scalpel holder, a pocket clip, and a comb (the comb goes into the same slot as the saw). I upgraded the main blade to 154CM. Most recently I added the Victorinox scissors from the Huntsman in place of the serrated blade. I added a bit of Dragon Grip tape to help get it out of my pocket.[attach id=0 msg=2418420]
[attach id=1 msg=2418420] -
Thanks GoBlue93!
The comb, pocket clip, and scalpel holder are all designed and 3D printed by me. Images of the 3D models I created are below. Of the three designs, the scalpel holders are the sturdiest, and can be printed out of PLA+, ASA, or Polycarbonate. The comb is printed out of nylon filament and made more flexible by throwing it in boiling water after it's printed. It's reasonably flexible but if you aren't careful with it, it can break, especially on the thinnest part where is goes around the pin (circled in red on the picture). Oh, and the comb tines are only about a quarter inch long, so for me it's a beard/mustache comb. I don't think it would work for the hair on the top of your head unless you have pretty short hair.I've been thinking I might want to send some of these prints to people willing to install them in their knives, field test them a bit, and give feedback. As it stands, I couldn't see ever charging money for the prints. The comb and pocket clip both seem too fragile to me (the part of the pocket clip that keeps breaking is also circled in red), but maybe with some feedback I can improve them. The scalpel holders are tougher, but if someone decides to apply a lot of pressure with the scalpel they would probably also fail (although, it's a scalpel, so applying pressure with it means you are probably using the wrong tool, IMHO). This project would probably warrant its own thread, but for those reading, does this sound like something folks on this forum would be interested in?
[attach id=0 msg=2418572]
[attach id=1 msg=2418572]
[attach id=2 msg=2418572]
[attach id=3 msg=2418572]



-
I would certainly be interested in receiving the files if you are willing to give them out. I've got friends with 3D printers, so I could get them printed myself. The scalpel blade holder seems very helpful.
-
Just catching up on this thread :o So many great mods, you all have given me so many ideas :ahhh I haven't done a mod in a while and think I may try my hand at it again :D

-
@customod said:
Tool Name: Spirit XNP (near perfect)
Basis: Victorinox Spirit X
Aim: Take a nearly perfect tool and make it even closer to perfect!
Mods:- Removed material from the side of the frame & add a slot in the knife blade so that it can be one hand opening. I also removed a small amount of material from near the pivot so the blade will open more easily.
- Did the same thing on the other side so the scissors can be opened one handed. Instead of a hole in the scissors, I just removed a little bit of material to help with friction.
- Removed material from the scissors so they aren't so restricted and I also took off a small amount of metal where the blades meet to form a chamfer in hopes that this would allow material to pass by more easily.
- Modified the can opener by making the 'blade' a continuous shape which is excellent for prying tight things like watch bezels or SAK scales and for carving spoons.
- Modified the inside part of the can opener to be a gutter/pull cutter.
- I guess it is a mod... I bought and added a pocket clip.
It is worth noting that the tool also lost 2 grams in the process and unfortunately gathered a bunch of small metal shavings between the tools. I'm still working them out. This was a bittersweet project because I now have a tool that may just be the pinnacle of all my multitools. Will this be the elusive 'goal' that will end my modding?
Links:
Where did you source the pocket clip? How does it attach?
Charles.
-
@Poncho Do it! Come on.

@ChopperCharles Victorinox has them as a separate product (both for the Swisstool and the Spirit models). I bought mine through a local watch sales store, but there are a lot of dealers who carry them.

-
Tool Name: Skeletool X
**Basis: **Skeletool
Aim: Add that little something I've been missing from carrying the Skeletool around.
Mods:- Removed most of the liner that holds the spare bit.
- Added scissors from A Gerber Truss (dropped right in and I also put in a thin washer to get just the right amount of friction)
- Modified scissor shape for even better fine work and took off a smidgen from the bit that presses against the spring so that the tip of the scissors near the pivot wouldn't accidentally get pushed up when closed.
- Designed and 3D printed an insert to the carabiner head that can hold 2 bits to replace the extra bit spot I lost.
Links:


-
wow!
-
Tool name: my wave
basis: wave plus
Aim: to make it more useful for my needs
Mods: replaced the blade with an s30v charge blade, added tweezers from victorinox under the woodsaw, took out the eyeglass driver and can opener, and installed a second bit driver for number 1/2 Phillips, and have 3 size flat drivers on other side.[attach id=0 msg=2444340]

-
Thats really cool, man what I would get myself into if I could 3d print parts.. great ingenuity designing a making your own bit holder
-
Way to make it yours! Looks like a proper tool.

-

This post is years old but I found you on a Google search. I made an account just to ask you about this project. This is exactly the thing I'm looking for my Style. Is there any way you could share the files for this project or I could even purchase them from you. Idk if you will ever see this but, awesome job this is really cool and I would love to add it to my Style. Hope to hear from you! -
@CrazyWildMan said:

This post is years old but I found you on a Google search. I made an account just to ask you about this project. This is exactly the thing I'm looking for my Style. Is there any way you could share the files for this project or I could even purchase them from you. Idk if you will ever see this but, awesome job this is really cool and I would love to add it to my Style. Hope to hear from you!Welcome CrazyWildMan, I assume you refer to this post?: /post/2387683 ?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login