Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Adding a pin slot to nylon

Scheduled Pinned Locked Moved Swiss Army Knights Forum
18 Posts 1 Posters 1.5k Views
  1. Home
  2. Tool Talk
  3. Swiss Army Knights Forum
  4. Adding a pin slot to nylon
Adding a pin slot to nylon
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • BPRoberts Offline
    BPRoberts
    Posts: 3,383
    BPRoberts Offline
    BPRoberts
    wrote on last edited by
    #3 Quote Reply

      So here's the knife:

      Front: [attach id=0 msg=2419886]

      Back: [attach id=1 msg=2419886]

      I think the scales are 3d printed. They have that "woven" texture 3d printer stuff often has. It was listed as a "Waiter Plus" but it's really a "Waiter with Plus Scales" which is still nice knife.

      As you can see, a pin would certainly fit in the standard spot: [attach id=2 msg=2419886]

      I tried heating one up with my Zippo, but couldn't get it in. Not sure if the "melt a pin hole" thing is just an internet legends (pins are pretty thin, I don't know that they'd be able to hold enough heat), if I did it wrong, or if the nylon is just tougher than cellidor.

      [attach id=3 msg=2419886]

      front.jpg

      back.jpg

      itfits.jpg

      zippo.jpg

      1 Reply Last reply
      • Old Boy Offline
        Old Boy
        Posts: 1,107
        Old Boy Offline
        Old Boy
        wrote on last edited by
        #4 Quote Reply

          @BPRoberts said:
          Not sure if the "melt a pin hole" thing is just an internet legends (pins are pretty thin, I don't know that they'd be able to hold enough heat), if I did it wrong, or if the nylon is just tougher than cellidor.

          I’ve done it with cellidor (58 mm Rambler) and it was hard for me to do as you had to reheat a sacrificial pin several times and have a steady hand. If that nylon has no pin slot then that’s a lot of material to go through.

          I’ve had better success removing the cellidor scale and melting a slot on the open scale. It was a lot cleaner. Not sure if your nylon scales are removable but you may want to carve a line to sit a hot pin and remove excess material. Just a guess though, never worked with nylon. Just sharing my cellidor experience.

          Even if you remove the scales I imagine your next worry is putting it back on if you don’t want to glue it?

          1 Reply Last reply
          • z1913 Offline
            z1913
            Posts: 853
            z1913 Offline
            z1913
            wrote on last edited by
            #5 Quote Reply

              If melting/drilling is too cumbersome you may try other option - store the pin in the tweezers.

              I do it with my Rambler for almost two years and it works just fine.

              The original pin might be too thick so a bit thinner pin might be needed.

              804E7925-D05B-4F1B-BD0D-CF5DC90C7452.jpg

              1 Reply Last reply
              • Echotech Offline
                Echotech
                Posts: 12,055
                Echotech Offline
                Echotech
                wrote on last edited by
                #6 Quote Reply

                  That's an interesting option z1913, not heard that one before :like:

                  Another option is to put the pin under the corkscrew, that works well enough you've just got to remember it's there when as it can fall out when you open it....a small nail works well too if you want something poky but more substantial

                  :cheers:

                  1 Reply Last reply
                  • BPRoberts Offline
                    BPRoberts
                    Posts: 3,383
                    BPRoberts Offline
                    BPRoberts
                    wrote on last edited by
                    #7 Quote Reply

                      Some interesting ideas... At the moment, I think I'm leaning towards clipping a safety pin to the corkscrew. Seems fairly secure, and gives a smidge more utility than a traditional pin anyway.

                      1 Reply Last reply
                      • nate j Offline
                        nate j
                        Posts: 6,226
                        nate j Offline
                        nate j
                        wrote on last edited by
                        #8 Quote Reply

                          @BPRoberts said:
                          Some interesting ideas... At the moment, I think I'm leaning towards clipping a safety pin to the corkscrew. Seems fairly secure, and gives a smidge more utility than a traditional pin anyway.

                          As an alternative, I suppose you could clip it to the key ring. Might be more out of the way than clipped to the corkscrew.

                          1 Reply Last reply
                          • Old Boy Offline
                            Old Boy
                            Posts: 1,107
                            Old Boy Offline
                            Old Boy
                            wrote on last edited by
                            #9 Quote Reply

                              I saw a post from an MTO member that had a paracord lanyard on their SAK that contained additional tools like tweezers, firestarter rod, etc. I forgot exactly.

                              But they took out the white strands and was left with the paracord casing. You could put a pin or even a sewing kit inside. If just a pin you could probably use any nylon or an unmodified paracord and just stick in a pin.

                              Beautiful knife by the way. Been meaning to get a Waiter myself and adding plus scales and opening up the additional toothpick slot.

                              1 Reply Last reply
                              • Rathbone Offline
                                Rathbone
                                Posts: 48
                                Rathbone Offline
                                Rathbone
                                wrote on last edited by
                                #10 Quote Reply

                                  My girlfriend does resin casting as a hobby. I get a lot of splinters at work so set her a little challenge.

                                  She made a mould of the toothpick then cast it around a needle.

                                  It's a bad pic but the number on the toothpick is visible.

                                  [attach id=0 msg=2420019]

                                  Pin Holder.jpg

                                  1 Reply Last reply
                                  • BPRoberts Offline
                                    BPRoberts
                                    Posts: 3,383
                                    BPRoberts Offline
                                    BPRoberts
                                    wrote on last edited by
                                    #11 Quote Reply

                                      That's a nice little piece of kit.

                                      1 Reply Last reply
                                      • BPRoberts Offline
                                        BPRoberts
                                        Posts: 3,383
                                        BPRoberts Offline
                                        BPRoberts
                                        wrote on last edited by BPRoberts
                                        #12 Quote Reply

                                          Current solution. I believe this is a size 0 (7/8"-22mm) safety pin. Deploy the corkscrew, unscrew the minidriver and screw the pin in the same as you would the driver (almost, but not quite all the way) to the bottom. Trust me, this is much easier than trying to "clip" it on at the bottom. Then reinsert the minidriver, adjust slightly as necessary so the pin sits well, close the corkscrew. If you don't carry the minidriver you can go up a size or two. I think this is better than putting it in the ring hole, since there's less wiggle and chance of it accidentally catching/opening in pocket. We'll see how it goes.

                                          safety.jpg

                                          1 Reply Last reply
                                          • Rizio Il Ghiro Offline
                                            Rizio Il Ghiro
                                            Posts: 4,263
                                            Rizio Il Ghiro Offline
                                            Rizio Il Ghiro
                                            wrote on last edited by
                                            #13 Quote Reply

                                              That’s a great idea! :like: :like: :cheers:

                                              1 Reply Last reply
                                              • Tasky Offline
                                                Tasky
                                                Posts: 808
                                                Tasky Offline
                                                Tasky
                                                wrote on last edited by
                                                #14 Quote Reply

                                                  Doesn't nylon have a higher melting point than cellidor?
                                                  It may just be you need a red-hot, or even white-hot, pin in order to make any headway with the melting, with constant re-heating as you go.
                                                  Certainly I'd suggest something like a MAPP torch, rather than a gas lighter.

                                                  1 Reply Last reply
                                                  • ComboTool Offline
                                                    ComboTool
                                                    Posts: 437
                                                    ComboTool Offline
                                                    ComboTool
                                                    wrote on last edited by
                                                    #15 Quote Reply

                                                      If you don't mind removing the scales you can easily ad a pin slot with a needle file.

                                                      1 Reply Last reply
                                                      • PitCarver Offline
                                                        PitCarver
                                                        Posts: 3,025
                                                        PitCarver Offline
                                                        PitCarver
                                                        wrote on last edited by
                                                        #16 Quote Reply

                                                          @BPRoberts said:
                                                          Current solution. I believe this is a size 0 (7/8"-22mm) safety pin. Deploy the corkscrew, unscrew the minidriver and screw the pin in the same as you would the driver (almost, but not quite all the way) to the bottom. Trust me, this is much easier than trying to "clip" it on at the bottom. Then reinsert the minidriver, adjust slightly as necessary so the pin sits well, close the corkscrew. If you don't carry the minidriver you can go up a size or two. I think this is better than putting it in the ring hole, since there's less wiggle and chance of it accidentally catching/opening in pocket. We'll see how it goes.

                                                          I really like this idea.

                                                          1 Reply Last reply
                                                          • SteveP Offline
                                                            SteveP
                                                            Posts: 1,321
                                                            SteveP Offline
                                                            SteveP
                                                            wrote on last edited by
                                                            #17 Quote Reply

                                                              I like that idea of threading the safety pin around the corkscrew.
                                                              :tu:

                                                              I've never tried it with nylon scales, but I haven't had any trouble heating a pin and inserting it into hollow cellidor scales, still attached to the SAK.

                                                              I struck out trying it with an old Champion with solid cellidor scales. I think because there was no place for the melted cellidor to go as I tried to force in the pin.

                                                              1 Reply Last reply

                                                              Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                              Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                              With your input, this post could be even better 💗

                                                              Register Login

                                                              1. Home
                                                              2. Tool Talk
                                                              3. Swiss Army Knights Forum
                                                              4. Adding a pin slot to nylon
                                                              Reply
                                                              • Reply as topic
                                                              Log in to reply
                                                              COMMUNITY LINKS
                                                              EDC-TV SAKWiki GearFeed SAKSelector
                                                              Operational Funds

                                                              Help us keep the Unworkable working!

                                                              Make A Donation
                                                              November Goal: $300.00
                                                              Due Date: Nov 30
                                                              Total Receipts: $0.00
                                                              Below Goal: $300.00
                                                              0% funded
                                                              • Login

                                                              • Don't have an account? Register

                                                              • Login or register to search.
                                                              • First post
                                                                Last post
                                                              0