Adding a pin slot to nylon
-
@BPRoberts said:
Not sure if the "melt a pin hole" thing is just an internet legends (pins are pretty thin, I don't know that they'd be able to hold enough heat), if I did it wrong, or if the nylon is just tougher than cellidor.I’ve done it with cellidor (58 mm Rambler) and it was hard for me to do as you had to reheat a sacrificial pin several times and have a steady hand. If that nylon has no pin slot then that’s a lot of material to go through.
I’ve had better success removing the cellidor scale and melting a slot on the open scale. It was a lot cleaner. Not sure if your nylon scales are removable but you may want to carve a line to sit a hot pin and remove excess material. Just a guess though, never worked with nylon. Just sharing my cellidor experience.
Even if you remove the scales I imagine your next worry is putting it back on if you don’t want to glue it?
-
If melting/drilling is too cumbersome you may try other option - store the pin in the tweezers.
I do it with my Rambler for almost two years and it works just fine.
The original pin might be too thick so a bit thinner pin might be needed.

-
That's an interesting option z1913, not heard that one before

Another option is to put the pin under the corkscrew, that works well enough you've just got to remember it's there when as it can fall out when you open it....a small nail works well too if you want something poky but more substantial

-
Some interesting ideas... At the moment, I think I'm leaning towards clipping a safety pin to the corkscrew. Seems fairly secure, and gives a smidge more utility than a traditional pin anyway.
-
@BPRoberts said:
Some interesting ideas... At the moment, I think I'm leaning towards clipping a safety pin to the corkscrew. Seems fairly secure, and gives a smidge more utility than a traditional pin anyway.As an alternative, I suppose you could clip it to the key ring. Might be more out of the way than clipped to the corkscrew.
-
I saw a post from an MTO member that had a paracord lanyard on their SAK that contained additional tools like tweezers, firestarter rod, etc. I forgot exactly.
But they took out the white strands and was left with the paracord casing. You could put a pin or even a sewing kit inside. If just a pin you could probably use any nylon or an unmodified paracord and just stick in a pin.
Beautiful knife by the way. Been meaning to get a Waiter myself and adding plus scales and opening up the additional toothpick slot.
-
My girlfriend does resin casting as a hobby. I get a lot of splinters at work so set her a little challenge.
She made a mould of the toothpick then cast it around a needle.
It's a bad pic but the number on the toothpick is visible.
[attach id=0 msg=2420019]

-
That's a nice little piece of kit.
-
Current solution. I believe this is a size 0 (7/8"-22mm) safety pin. Deploy the corkscrew, unscrew the minidriver and screw the pin in the same as you would the driver (almost, but not quite all the way) to the bottom. Trust me, this is much easier than trying to "clip" it on at the bottom. Then reinsert the minidriver, adjust slightly as necessary so the pin sits well, close the corkscrew. If you don't carry the minidriver you can go up a size or two. I think this is better than putting it in the ring hole, since there's less wiggle and chance of it accidentally catching/opening in pocket. We'll see how it goes.

-
That’s a great idea!

-
Doesn't nylon have a higher melting point than cellidor?
It may just be you need a red-hot, or even white-hot, pin in order to make any headway with the melting, with constant re-heating as you go.
Certainly I'd suggest something like a MAPP torch, rather than a gas lighter. -
If you don't mind removing the scales you can easily ad a pin slot with a needle file.
-
@BPRoberts said:
Current solution. I believe this is a size 0 (7/8"-22mm) safety pin. Deploy the corkscrew, unscrew the minidriver and screw the pin in the same as you would the driver (almost, but not quite all the way) to the bottom. Trust me, this is much easier than trying to "clip" it on at the bottom. Then reinsert the minidriver, adjust slightly as necessary so the pin sits well, close the corkscrew. If you don't carry the minidriver you can go up a size or two. I think this is better than putting it in the ring hole, since there's less wiggle and chance of it accidentally catching/opening in pocket. We'll see how it goes.I really like this idea.
-
I like that idea of threading the safety pin around the corkscrew.

I've never tried it with nylon scales, but I haven't had any trouble heating a pin and inserting it into hollow cellidor scales, still attached to the SAK.
I struck out trying it with an old Champion with solid cellidor scales. I think because there was no place for the melted cellidor to go as I tried to force in the pin.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login