Show your slip joint's thread!
-
I can see what you mean about the nail nick, it even looks wrong there. :-\
The Otter-Messer on the other hand looks very nice.

-
So to hear your Ablett was under parr too - you should send it back for a refund, that's what I did. Why waste money on something you don;t like or want? ???
-
Too late...already started to sharpen it :P
I also have a cunning plan to deal with the nail nick issue...
-
The Otter is old school sweetness



-
Shame about the Ablett :-\
At least the Otter is perfection itself

-
@SporkBob NoPants said:
Too late...already started to sharpen it :PI also have a cunning plan to deal with the nail nick issue...
I have complete confidence that you can and will turn it in to a decent knife. The shame of it being that you shouldn't have to >:(
-
I'd still fire off an email to them and see how they defend the QC

-
The Ablett is now evil-sharp and much easier to open...


-
Major improvement mate - please send them the pic and show them how it should be done ;)
-
Spork,
Damn, it sucks that the Albett came the way it did. Looks like the QC is quite lacking on a consistant basis. I'll scratch them off my list. I do like the looks of the Otter-Messer, that puppy looks sweet! What's the steel in them OM's?
And I like your fix to the Albett.......I'm going to assume there was Dremel usage here! And nice edge too, convex I will assume?
2xTap
-
@2xTap said:
...I'm going to assume there was Dremel usage here! And nice edge too, convex I will assume?...Yep! :D It only took a few minutes with the 1/2" sanding drum. The edge is sort of convex...I had to spend some time with a coarse SC Norton to get edge and tip thinned down enough. Typically I hold the blade almost flat to make a wide secondary bevel, then blend in the shoulders.
The Otter is carbon steel...don't know what flavor :P - bought both from Worldknives
-
That Ablett looks MUCH better now :)
-
got these in a while ago

-
@SporkBob NoPants said:
...I'm going to assume there was Dremel usage here! And nice edge too, convex I will assume?...
Yep! :D It only took a few minutes with the 1/2" sanding drum. The edge is sort of convex...I had to spend some time with a coarse SC Norton to get edge and tip thinned down enough. Typically I hold the blade almost flat to make a wide secondary bevel, then blend in the shoulders.
The Otter is carbon steel...don't know what flavor :P - bought both from Worldknives
WOW......I assumed twice and was right on both accounts. That's a first for me! :D
Looks good bud, that "easy-open" notch you made actually fits the knife, like it was meant to be there if you know what I mean!
And thanks for the link, hadn't been there in a long while.

2xTap
-
@kiwiblade said:
got these in a while ago

Carbon slippies

-
Very nice slippies kiwi, lots of proper looking knives!
-
Here's some eye-candy of my latest Case acquisition. Now I am not much for Country Music and can't say I am a fan of Brooks & Dunn........but their logo/brand marked on a Case does make for a nice looking Stockman:
Hopefully all these pics will show up, Imageshack is having problems right now for some reason!


This is from the first run of "Brooks & Dunn" Series slips by Case, made in 2008. This particular one is on Case's #75 pattern Large Stockman which sits in at 4 1/4" closed. The blades are Case's mirror polished "Tru-Sharp" Stainless (420HC) with brass liners and pins, nickel/silver bolsters, and stainless backsprings. Scales are left natural and made from smooth Zebu cattle shin bone. No inlayed shield here as the shield is actually lasered into the bone, the B&D Steer Skull...........

.................love the look, they could of just left it at that without the "Brooks & Dunn" etch on the blade and that would have been fine by me.
Fit and Finish is excellent. Blades are even ground and polished with clean edges that are typical Case sharp. No blade play any where and the backsprings have that hefty stoutness that isn't nailbreaking and all backsprings sit flush with the blades opened or closed. Scales are fitted virtually seamless and pins are flush with the bone.....smooth as a baby's butt from bolster to bolster. The backspring area is nicely polished and the springs all sit flush and smooth, but there is one little fault here. The mainblade's backspring on the pivot end has a faint gap between it and the brass spring spacer. It's a little over a inch long or so and very minor, doesn't affect anything, but it is there.......

........you really have to look to see it as it is faint but this is a peeve of mine. Even still it is minor. But outside of that it is clean and seamless.
It came in a "Brooks & Dunn" collector tin which also includes a suede slip-pouch. A real nice combination considering it all costed a mere $44.99 NIB! I'm a bargain shopper. :D
2xTap
-
That might be the shiniest thing I've seen all day :)
Great deal for that price too, what with brass liners and such.
-
I agree about the etching on the blade, I really wish companies wouldn't do that, what's wrong with a tang stamp? Other than that it looks gorgeous.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login