Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Show your slip joint's thread!

Scheduled Pinned Locked Moved Edged Tools
3.7k Posts 1 Posters 342.3k Views
  1. Home
  2. Tool Talk
  3. Edged Tools
  4. Show your slip joint's thread!
Show your slip joint's thread!
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • Spork, Lord of Lime Jello! Offline
    Spork, Lord of Lime Jello!
    Posts: 3,516
    Spork, Lord of Lime Jello! Offline
    Spork, Lord of Lime Jello!
    wrote on last edited by
    #239 Quote Reply

      The Ablett is now evil-sharp and much easier to open...

      slip_ablett01.jpg

      slip_ablett02.jpg

      1 Reply Last reply
      • nuphoria Offline
        nuphoria
        Admin Team
        Posts: 15,038
        nuphoria Offline
        nuphoria
        Admin Team
        wrote on last edited by
        #240 Quote Reply

          Major improvement mate - please send them the pic and show them how it should be done ;)

          1 Reply Last reply
          • 2xTap Offline
            2xTap
            Posts: 1,220
            2xTap Offline
            2xTap
            wrote on last edited by
            #241 Quote Reply

              Spork,

              Damn, it sucks that the Albett came the way it did. Looks like the QC is quite lacking on a consistant basis. I'll scratch them off my list. I do like the looks of the Otter-Messer, that puppy looks sweet! What's the steel in them OM's?

              And I like your fix to the Albett.......I'm going to assume there was Dremel usage here! And nice edge too, convex I will assume?

              2xTap

              1 Reply Last reply
              • Spork, Lord of Lime Jello! Offline
                Spork, Lord of Lime Jello!
                Posts: 3,516
                Spork, Lord of Lime Jello! Offline
                Spork, Lord of Lime Jello!
                wrote on last edited by
                #242 Quote Reply

                  @2xTap said:
                  ...I'm going to assume there was Dremel usage here! And nice edge too, convex I will assume?...

                  Yep! :D It only took a few minutes with the 1/2" sanding drum. The edge is sort of convex...I had to spend some time with a coarse SC Norton to get edge and tip thinned down enough. Typically I hold the blade almost flat to make a wide secondary bevel, then blend in the shoulders.

                  The Otter is carbon steel...don't know what flavor :P - bought both from Worldknives

                  1 Reply Last reply
                  • Mike, Lord of the Spammers! Offline
                    Mike, Lord of the Spammers!
                    Posts: 42,975
                    Mike, Lord of the Spammers! Offline
                    Mike, Lord of the Spammers!
                    wrote on last edited by
                    #243 Quote Reply

                      That Ablett looks MUCH better now :)

                      1 Reply Last reply
                      • kiwiblade Offline
                        kiwiblade
                        Posts: 84
                        kiwiblade Offline
                        kiwiblade
                        wrote on last edited by
                        #244 Quote Reply

                          got these in a while ago

                          1 Reply Last reply
                          • 2xTap Offline
                            2xTap
                            Posts: 1,220
                            2xTap Offline
                            2xTap
                            wrote on last edited by
                            #245 Quote Reply

                              @SporkBob NoPants said:

                              @2xTap said:

                              ...I'm going to assume there was Dremel usage here! And nice edge too, convex I will assume?...

                              Yep! :D It only took a few minutes with the 1/2" sanding drum. The edge is sort of convex...I had to spend some time with a coarse SC Norton to get edge and tip thinned down enough. Typically I hold the blade almost flat to make a wide secondary bevel, then blend in the shoulders.

                              The Otter is carbon steel...don't know what flavor :P - bought both from Worldknives

                              WOW......I assumed twice and was right on both accounts. That's a first for me! :D

                              Looks good bud, that "easy-open" notch you made actually fits the knife, like it was meant to be there if you know what I mean!

                              And thanks for the link, hadn't been there in a long while. :tu:

                              2xTap

                              1 Reply Last reply
                              • Mike, Lord of the Spammers! Offline
                                Mike, Lord of the Spammers!
                                Posts: 42,975
                                Mike, Lord of the Spammers! Offline
                                Mike, Lord of the Spammers!
                                wrote on last edited by
                                #246 Quote Reply

                                  @kiwiblade said:
                                  got these in a while ago

                                  Carbon slippies :drool: :drool:

                                  1 Reply Last reply
                                  • nuphoria Offline
                                    nuphoria
                                    Admin Team
                                    Posts: 15,038
                                    nuphoria Offline
                                    nuphoria
                                    Admin Team
                                    wrote on last edited by
                                    #247 Quote Reply

                                      Very nice slippies kiwi, lots of proper looking knives!

                                      1 Reply Last reply
                                      • 2xTap Offline
                                        2xTap
                                        Posts: 1,220
                                        2xTap Offline
                                        2xTap
                                        wrote on last edited by
                                        #248 Quote Reply

                                          Here's some eye-candy of my latest Case acquisition. Now I am not much for Country Music and can't say I am a fan of Brooks & Dunn........but their logo/brand marked on a Case does make for a nice looking Stockman:

                                          Hopefully all these pics will show up, Imageshack is having problems right now for some reason!

                                          This is from the first run of "Brooks & Dunn" Series slips by Case, made in 2008. This particular one is on Case's #75 pattern Large Stockman which sits in at 4 1/4" closed. The blades are Case's mirror polished "Tru-Sharp" Stainless (420HC) with brass liners and pins, nickel/silver bolsters, and stainless backsprings. Scales are left natural and made from smooth Zebu cattle shin bone. No inlayed shield here as the shield is actually lasered into the bone, the B&D Steer Skull...........

                                          .................love the look, they could of just left it at that without the "Brooks & Dunn" etch on the blade and that would have been fine by me.

                                          Fit and Finish is excellent. Blades are even ground and polished with clean edges that are typical Case sharp. No blade play any where and the backsprings have that hefty stoutness that isn't nailbreaking and all backsprings sit flush with the blades opened or closed. Scales are fitted virtually seamless and pins are flush with the bone.....smooth as a baby's butt from bolster to bolster. The backspring area is nicely polished and the springs all sit flush and smooth, but there is one little fault here. The mainblade's backspring on the pivot end has a faint gap between it and the brass spring spacer. It's a little over a inch long or so and very minor, doesn't affect anything, but it is there.......

                                          ........you really have to look to see it as it is faint but this is a peeve of mine. Even still it is minor. But outside of that it is clean and seamless.

                                          It came in a "Brooks & Dunn" collector tin which also includes a suede slip-pouch. A real nice combination considering it all costed a mere $44.99 NIB! I'm a bargain shopper. :D

                                          2xTap

                                          1 Reply Last reply
                                          • nuphoria Offline
                                            nuphoria
                                            Admin Team
                                            Posts: 15,038
                                            nuphoria Offline
                                            nuphoria
                                            Admin Team
                                            wrote on last edited by
                                            #249 Quote Reply

                                              That might be the shiniest thing I've seen all day :)

                                              Great deal for that price too, what with brass liners and such.

                                              1 Reply Last reply
                                              • Gareth Offline
                                                Gareth
                                                Admin Team
                                                Posts: 37,725
                                                Gareth Offline
                                                Gareth
                                                Admin Team
                                                wrote on last edited by
                                                #250 Quote Reply

                                                  I agree about the etching on the blade, I really wish companies wouldn't do that, what's wrong with a tang stamp? Other than that it looks gorgeous. :drool:

                                                  1 Reply Last reply
                                                  • Benner Offline
                                                    Benner
                                                    Posts: 28,081
                                                    Benner Offline
                                                    Benner
                                                    wrote on last edited by
                                                    #251 Quote Reply

                                                      Nice :drool:

                                                      1 Reply Last reply
                                                      • John Offline
                                                        John
                                                        Posts: 4,320
                                                        John Offline
                                                        John
                                                        wrote on last edited by
                                                        #252 Quote Reply

                                                          @SporkBob NoPants said:
                                                          The Ablett is now evil-sharp and much easier to open...

                                                          Ok I'll ask I'm stupid when it comes to sharpening in fact I can make a dull blade duller I'm to heavy handed could be the cause :think: ,I have a dremel :salute: so how's it done :D

                                                          1 Reply Last reply
                                                          • Spork, Lord of Lime Jello! Offline
                                                            Spork, Lord of Lime Jello!
                                                            Posts: 3,516
                                                            Spork, Lord of Lime Jello! Offline
                                                            Spork, Lord of Lime Jello!
                                                            wrote on last edited by
                                                            #253 Quote Reply

                                                              First off...put the Dremel down and back away slowly. :o

                                                              I'm old school and use flat stones. I re-profiled the secondary on a coarse side silicon carbide stone, holding the blade almost flat...raised a burr on one side, then the other. Then I ran it on the fine side of the stone.

                                                              Once that was done I used progressively finer wet/dry paper on a stiff rubber pad (not a mouse pad) to clean up and blend the shoulder of the secondary into a convex...followed by a stropping with black then green compound.

                                                              Unless the blade gets abused, stopping will keep it sharp for a long time before having to resort to stoning again…and usually a fine grit stone will do the job.

                                                              I test my edges on leather scraps and by making wood shavings. I find paper cutting and shaving hair deceptive...it doesn’t give me a true indication of how well the edge will cut in thicker materials or how well it will carve wood.

                                                              ablett_stone.jpg

                                                              1 Reply Last reply
                                                              • 2xTap Offline
                                                                2xTap
                                                                Posts: 1,220
                                                                2xTap Offline
                                                                2xTap
                                                                wrote on last edited by
                                                                #254 Quote Reply

                                                                  Ok, latest GEC acquistion just came in this morning. This one a bit unique, Great Eastern Cutlery #23 pattern "Left-Hand" Pioneer Jumbo Trapper.

                                                                  Finally got around to getting one. I'm not left handed but it doesn't matter, you don't see many companies doing a lefty slipjoint. The only difference between these and a regular Pioneer is that the Spey and Clip blades have swapped sides. The shield is still on the same side as the "Right-Handers".

                                                                  These are of 2007 manufacture and are the Pioneer #23 pattern at 4.5" closed. Mine is serial number #10 out of the run. They are GEC brand with the Cyclops Steel Works blade etch making them 440-C bladed. Typical GEC construction with nickle/silver bolsters, brass liners and pins, and stout backsprings.

                                                                  Fit and finish is near flawless, one minor issue I did find though is in the polish of the blades. On this one the polish is a bit hazy, kinda like it wasn't completed......like the person doing these didn't spend enough time on the buffer. Nothing big as it is consistant throughout both blades, just not as nicely done as my others. Outside of that this thing is flawless and gap free.

                                                                  As to the edges, one thing I have heard people complain about on GEC's recently. This one, like my others, have sharp usable edges. They ain't scary sharp but will remove arm hair......just not as effortlessly as some of my other slips. But they ain't butter knife dull.

                                                                  The bone on this one is that River Blue Bone. Very nice color, kinda deep in hue but does lighten up a bit in areas. The jig is like a Stag Bone jig, really nice.

                                                                  I ordered this one from Mike over at CollectorKnives.net, and along with it I ordered one of the new GEC Blade picks in Buffalo Horn.........

                                                                  .........real nice little piece with a slim profile. Made of stainless with slim Buffalo Horn slabs pinned on both sides. The scales on this have nice angular edges all the way around. I didn't get this one to use as I don't have problems getting my GEC's open, I got it for my collection to go along side my Buffalo Horn and Ox Horn Pioneers. These picks are 3 3/8" long and at their thickest point, across the scales, they are only about 3/16" thick.

                                                                  2xTap :tu:

                                                                  1 Reply Last reply
                                                                  • jzmtl Offline
                                                                    jzmtl
                                                                    Posts: 8,551
                                                                    jzmtl Offline
                                                                    jzmtl
                                                                    wrote on last edited by
                                                                    #255 Quote Reply

                                                                      @Spork said:
                                                                      First off...put the Dremel down and back away slowly. :o

                                                                      It's actually possible to use dremel to do an okay job. Use the non-reinforced cutting disk thou not grinding stone. Use the side of disk as you would a flat stone, keep it slow and cool.

                                                                      1 Reply Last reply
                                                                      • John Offline
                                                                        John
                                                                        Posts: 4,320
                                                                        John Offline
                                                                        John
                                                                        wrote on last edited by John
                                                                        #256 Quote Reply

                                                                          Here's my fav slip joint ATM thank ringzero :tu:

                                                                          I decided to de-badge it >:D the etching on the blade gone!

                                                                          And a not so great tip for some but! it's how I like to EDC my knives why? well it could afford me seconds or even minutes depending on the intellect of a potential assailant(should they want to turn my knife against me) :salute: also it works great when you have little enquiring minds in your family :tu:

                                                                          1 Reply Last reply
                                                                          • ? This user is from outside of this forum
                                                                            Guest
                                                                            Posts:
                                                                            ? This user is from outside of this forum
                                                                            Guest
                                                                            wrote on last edited by
                                                                            #257 Quote Reply

                                                                              The Fallkie U1 could never be called pretty, but it's non threatening looking and very functional. Very well put together too.

                                                                              1 Reply Last reply
                                                                              • nuphoria Offline
                                                                                nuphoria
                                                                                Admin Team
                                                                                Posts: 15,038
                                                                                nuphoria Offline
                                                                                nuphoria
                                                                                Admin Team
                                                                                wrote on last edited by
                                                                                #258 Quote Reply

                                                                                  @Magic Bus said:
                                                                                  The Fallkie U1 could never be called pretty, but it's non threatening looking and very functional. Very well put together too.

                                                                                  I didn't get on with it personally, lovely looking little thing but not really comfy in my hand.

                                                                                  1 Reply Last reply

                                                                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                                                  With your input, this post could be even better 💗

                                                                                  Register Login

                                                                                  • 1
                                                                                  • 2
                                                                                  • 11
                                                                                  • 12
                                                                                  • 13
                                                                                  • 14
                                                                                  • 15
                                                                                  • 184
                                                                                  • 185
                                                                                  1. Home
                                                                                  2. Tool Talk
                                                                                  3. Edged Tools
                                                                                  4. Show your slip joint's thread!
                                                                                  Reply
                                                                                  • Reply as topic
                                                                                  Log in to reply
                                                                                  COMMUNITY LINKS
                                                                                  EDC-TV SAKWiki GearFeed SAKSelector
                                                                                  Operational Funds

                                                                                  Help us keep the Unworkable working!

                                                                                  Make A Donation
                                                                                  November Goal: $300.00
                                                                                  Due Date: Nov 30
                                                                                  Total Receipts: $0.00
                                                                                  Below Goal: $300.00
                                                                                  0% funded
                                                                                  • Login

                                                                                  • Don't have an account? Register

                                                                                  • Login or register to search.
                                                                                  • First post
                                                                                    Last post
                                                                                  0