*** The Dean 51 Traditional Challenge 2023 ***
-
Sorry for being silent over the last 2 days - I am in my busiest time of the year... annual reviews :ahhh :ahhh
Todays pic is one of my largest Case knives. Case calls it a 6.5 BoneStag Trapper, but a lot of sellers call it a Wharncliffe Trapper, and it's a hefty beast


That very pretty Bone/Stag!
And I do like the blade set on your Trapper.
I have a single blade Wharncliffe Trapper, the other r 3 Trappers are Clip point and Spey blade sets. -
@LoopCutter said:
Very nice use, Nate!
How many cigars can be prepped before a blade touch up!
I must admit that I have no idea.
It’s very rare that I smoke more than 2-3 cigars per day, and some days it is one or none. I don’t find daily or even weekly touch ups necessary.
Assuming a blade made of good steel, properly heat treated, well-sharpened initially, and with appropriate geometry to do the job in the first place, I think the answer would have to be “a lot”.
Analyzing a bit more, taking 60 ring gauge as the largest common size, remembering that with cigars ring gauge is 64ths of an inch diameter, and recalling C = pi*D, the length of cut to cap a cigar is less than 3 inches. If you have to cut through filler and binders, the cross sectional area is less than 0.7 square inches.
-
Day 10
Cigar duty, fingernail whittling, and cut the tags off a new shirt for one of my daughters.

-
I only ask because, when in high school I made friends with a boy from Japan. His father taught metallurgy at the university. His father had a display of several different Japanese swords. The larger ones I remember being most interesting, as his father explained that when the blade was made it was tested. The higher number of marks on blade indicated the highest quality. He said they tested blades on slaves and each mark indicated cutting a slave in half. And that is how many, then blade must be sharpened.
Also, my grandfather’s cousins made Cigars in Kalamazoo, we occasional would visit them near closing time (on our way home from farmers market), so he could buy their mess ups. But I recall as they cleaned the shop at closing, they always sharpened each of their knives used for cutting tobacco and wrap leaves. Start the new day ready to rock and roll. 😉
-
@LoopCutter said:
That very pretty Bone/Stag!
And I do like the blade set on your Trapper.
I have a single blade Wharncliffe Trapper, the other r 3 Trappers are Clip point and Spey blade sets.Thank you

You posted a Copperhead that I have been eyeing... I need to ask you about it when I have more time.
-
Day 11
Unlike most of the knives I have been posting, I'm actually carrying this one today. It's a 2-blade congress with black micarta - it's one of the vault patterns for 2023.

-
6308 Whittier

Sent from my iPhone using Tapatalk
-
-
Day 11
So, other than the usual parcel/packaging opening, I actually used my Case #18 for something else. Taking the dog for a walk and we took a couple of small paths that are off the beaten track. Little used meant that in quite a few places there was thorny bramble stems hooked from one side of the path to the other. Secateurs or a machete might have been more appropriate, but the careful application of the Stockman cleared the way enough. :D (had I been wearing the Barbour I could have ignored most of them, but I was just in a Polo shirt)

-
-
Day 11
It looks like the recent discussion on the Congress pattern is bringing some out today. Nice ones Rich and BPR!
I have mine with me as well, a 2009 #52 medium Congress in red bone and CV. If you want a knife with a great selection of thin, scapel-sharp blades, this is it.

-
Day 10
CS and CV

-
-
@LoopCutter said:
Day 10Wharncliffe models with Micarta covers will share POCKET duties this day!
[attach id=0 msg=2427398]Very nice!
Sent fra min M2002J9G via Tapatalk
-
@LoopCutter said:
I only ask because, when in high school I made friends with a boy from Japan. His father taught metallurgy at the university. His father had a display of several different Japanese swords. The larger ones I remember being most interesting, as his father explained that when the blade was made it was tested. The higher number of marks on blade indicated the highest quality. He said they tested blades on slaves and each mark indicated cutting a slave in half. And that is how many, then blade must be sharpened.Also, my grandfather’s cousins made Cigars in Kalamazoo, we occasional would visit them near closing time (on our way home from farmers market), so he could buy their mess ups. But I recall as they cleaned the shop at closing, they always sharpened each of their knives used for cutting tobacco and wrap leaves. Start the new day ready to rock and roll. [emoji6]
Cool story, but I have to say it sounds a bit like a myth they did that

Sent fra min M2002J9G via Tapatalk
-
Day 11:
Whittled a little dude for the kid


-
Day 11:
You are all to blame for this...[emoji1787]
-
So, other than the usual parcel/packaging opening, I actually used my Case #18 for something else. Taking the dog for a walk and we took a couple of small paths that are off the beaten track. Little used meant that in quite a few places there was thorny bramble stems hooked from one side of the path to the other. Secateurs or a machete might have been more appropriate, but the careful application of the Stockman cleared the way enough. :D (had I been wearing the Barbour I could have ignored most of them, but I was just in a Polo shirt)
That is hard work for your Stockman! Ratio of blade to bramble makes it necessary to sharpen strop the blade post adventure. 🥹
-
@McStitchy said:
I have seen one before 
@Gareth said:
Always loved a good whittler backspring set-up as well.Kudos on the rebellious box opening, I'd have done exactly the same thing.

:D
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

