*** The Dean 51 Traditional Challenge 2023 ***
-
-
Day 11
So, other than the usual parcel/packaging opening, I actually used my Case #18 for something else. Taking the dog for a walk and we took a couple of small paths that are off the beaten track. Little used meant that in quite a few places there was thorny bramble stems hooked from one side of the path to the other. Secateurs or a machete might have been more appropriate, but the careful application of the Stockman cleared the way enough. :D (had I been wearing the Barbour I could have ignored most of them, but I was just in a Polo shirt)

-
-
Day 11
It looks like the recent discussion on the Congress pattern is bringing some out today. Nice ones Rich and BPR!
I have mine with me as well, a 2009 #52 medium Congress in red bone and CV. If you want a knife with a great selection of thin, scapel-sharp blades, this is it.

-
Day 10
CS and CV

-
-
@LoopCutter said:
Day 10Wharncliffe models with Micarta covers will share POCKET duties this day!
[attach id=0 msg=2427398]Very nice!
Sent fra min M2002J9G via Tapatalk
-
@LoopCutter said:
I only ask because, when in high school I made friends with a boy from Japan. His father taught metallurgy at the university. His father had a display of several different Japanese swords. The larger ones I remember being most interesting, as his father explained that when the blade was made it was tested. The higher number of marks on blade indicated the highest quality. He said they tested blades on slaves and each mark indicated cutting a slave in half. And that is how many, then blade must be sharpened.Also, my grandfather’s cousins made Cigars in Kalamazoo, we occasional would visit them near closing time (on our way home from farmers market), so he could buy their mess ups. But I recall as they cleaned the shop at closing, they always sharpened each of their knives used for cutting tobacco and wrap leaves. Start the new day ready to rock and roll. [emoji6]
Cool story, but I have to say it sounds a bit like a myth they did that

Sent fra min M2002J9G via Tapatalk
-
Day 11:
Whittled a little dude for the kid


-
Day 11:
You are all to blame for this...[emoji1787]
-
So, other than the usual parcel/packaging opening, I actually used my Case #18 for something else. Taking the dog for a walk and we took a couple of small paths that are off the beaten track. Little used meant that in quite a few places there was thorny bramble stems hooked from one side of the path to the other. Secateurs or a machete might have been more appropriate, but the careful application of the Stockman cleared the way enough. :D (had I been wearing the Barbour I could have ignored most of them, but I was just in a Polo shirt)
That is hard work for your Stockman! Ratio of blade to bramble makes it necessary to sharpen strop the blade post adventure. 🥹
-
@McStitchy said:
I have seen one before 
@Gareth said:
Always loved a good whittler backspring set-up as well.Kudos on the rebellious box opening, I'd have done exactly the same thing.

:D -
A lot of good exchanges and photo in the last two pages, and interesting idea concept on how to hold the Congress in reverse grip for whittling. Gonna admit I never did see that pattern in that light, and learn something new today!

Day 11

Large stockman liberate something I have longed to try...
This is surprisingly good, fair amount of heat and good flavor for otherwise mundane mac and cheese. If there is any company that could pull this off, it will be Mountain House. Life is an adventure, get some! :D -
@RF52 said:
Cool story, but I have to say it sounds a bit like a myth they did that
Sent fra min M2002J9G via Tapatalk
It may have been, I remember what he showed and told me.
Only the larger swords had these marks. IIRC, from 13th or 14th century.Another item he shared, was that the larger two-handed swords were even more rare, because, during WWII, Japanese officers would cut their family swords handles down to meet the max length allow for duty carry.
This was in late 60s when I enjoyed and was welcome into their home.I since, had been fascinated by Japanese history and culture. I also, recall that it became illegal for families to export, sell, or travel from Japan with any Swords made by the old craftsman of Japan.
-
Day 11
Amber Bone and Texas Jack
[attach id=0 msg=2427655]
032 CV pattern from 2008Over the same Amber bone 47 Stockman. 2020.

-
You Sodbuster folks have a serious problem. I thought I was bad...

-
@LoopCutter said:
It may have been, I remember what he showed and told me.
Only the larger swords had these marks. IIRC, from 13th or 14th century.Another item he shared, was that the larger two-handed swords were even more rare, because, during WWII, Japanese officers would cut their family swords handles down to meet the max length allow for duty carry.
This was in late 60s when I enjoyed and was welcome into their home.I since, had been fascinated by Japanese history and culture. I also, recall that it became illegal for families to export, sell, or travel from Japan with any Swords made by the old craftsman of Japan.
Don't get me wrong, I love old stories, myths and legends. Got all kinds of mythological creatures from Japanese stories tattooed on me. And I can only imagine how awesome it would be to get a history lesson and see those incredible blades [emoji2]
Sent fra min M2002J9G via Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login




:D