italian knife makers (MKM/Viper/Fox/maserin/lionsteel/mercury...)
-
Hello,
Looks like there is no dedicated knife clubs for the Italian brands, maybe they don't need a dedicated thread for each yet, so here is one to show them all
Let's start with
- MKM with the MKM Flame (designed by Michael Zieba based on his MS3 model and produced by Mikita)
& - Viper (Tecnocut SNC) with the Hug2 (designed by Sacha Thiel based on his Birdy model and produced by Viper)
[attach id=0 msg=2434073]
Both of these specific variants feature m390 blade, titanium frame, and carbon fiber scales (Fat Carbon® Dark Matter Blue for the Hug)
These are very high quality and top notch finish knives with high end components at around 150-200€ where Benchmade gives you grivory at that price point (not that polymer is bad, but it's not as nice to carry)(I also have another MKM Flame in blue anodized titanium which is also very nice)
I don't have any Lionsteel knives at the moment but they also are top notch fit and finish. Fox might be more budget oriented (even if they have different brands depending on the target), Maserin have a wide range of product too.
Show is yours please! These brands deserve to be known and tried


- MKM with the MKM Flame (designed by Michael Zieba based on his MS3 model and produced by Mikita)
-
That Viper Hug is sexy! I'm seriously going to have to consider getting one.
Here's my Shuffler. It's basically a Barlow for modern times. The machine work and fit and finish are outstanding. My only complaint is that it's a bit thick behind the edge.
M390 Steel, Titanium frame and bolsters, Ebony scales.

-
That is a very nice interpretation of the Barlow, do you remember it's price range ?
-
Right around $120 I believe. I got this one pre-owned on ebay for a bit less than that.
The Hug seems like a lot of knife for the price but it's bigger than I'd likely carry much in a pocket. That modified Wharncliffe looks like a great profile for daily carry.
-
Thank you,
It is not that big (the MKM Flame is small on the other hand!) -
Here is a picture of it between two welknown folders :
[attach id=0 msg=2434336]
Benchmade Bugout and Minigriptilian

-
Nice! Very nice!
I have a few Italian made knives and been pondering should I choose Italy or Finland for September’s flag challenge. I think this swings it and I’ll be doing ItalySent from my iPhone using Tapatalk
-
Let’s see…
Lionsteel Warhorse
Lionsteel Shuffler
Viper Key
Fox Bravado
Cold Steel Lucky Two

-
Very cool ! (especially the gradient on the Viper Key)
So the Cold Steel Lucky Two is Italian made?
-
@m47mu74nt said:
So the Cold Steel Lucky Two is Italian made?Indeed it is. It’s hard to read in my previous pic, but the PE blade is simply marked “LUCKY”, while the SE blade is marked “COLD STEEL CPM-S35VN ITALY”.
It’s an under-appreciated knife IMO. Only 1.2 ounces, about 3 1/4” closed, carbon fiber handle slabs, two CPM-S35VN blades (one PE and one SE) that are a bit over 2.5” long with about 2 1/4” sharp (roughly the size of a 91 mm SAK main blade), and available for $70.
The pocket clip is basic but functional, doesn’t interfere with getting a good grip on the knife, and if nothing else provides a useful indication of which blade is which, as the knife is otherwise completely symmetrical when closed.


-
That's a pretty cool little knife. Kind of a modern Muskrat.
-
How about one of these? The Spyderco Roadie, made by Lionsteel at Maniago for Spyderco, and very nice it is too.....

-
This thread is getting more and more interesting !
-
Because one wasn't enough (and the price was pretty low compared to MSRP), I got another Viper Hug, this time with red Fat carbon scales and only bolsters of the pivot side
-
Beautiful!I've been very close to pushing the button on a natural Micarta one with bolsters on both ends.
-
Go for it without hesitation: the two bolsters variants look absolutely stunning (I really wish the red fat carbon one was with two bolsters too, it really gives a more 'dynamic' look )
-
There sure are some great sharps in this thread!
I've come pretty close to pulling the trigger on a Maserin fixed blade. -
@nate j said:
Indeed it is. It’s hard to read in my previous pic, but the PE blade is simply marked “LUCKY”, while the SE blade is marked “COLD STEEL CPM-S35VN ITALY”.It’s an under-appreciated knife IMO. Only 1.2 ounces, about 3 1/4” closed, carbon fiber handle slabs, two CPM-S35VN blades (one PE and one SE) that are a bit over 2.5” long with about 2 1/4” sharp (roughly the size of a 91 mm SAK main blade), and available for $70.
The pocket clip is basic but functional, doesn’t interfere with getting a good grip on the knife, and if nothing else provides a useful indication of which blade is which, as the knife is otherwise completely symmetrical when closed.
Wow, that's a lot of knife for 70, nice buy!
@m47mu74nt said:
Because one wasn't enough (and the price was pretty low compared to MSRP), I got another Viper Hug, this time with red Fat carbon scales and only bolsters of the pivot side
I remembered eyeing this Viper for the longest time, in general, I do find myself quite attracted to Viper designs.
-
Here are my two profferings, which given that Mrs Surge is a full on Italian, is pretty poor

First an Antonini Rescue Knife* (purchased from a member) wearing a set of Ranger Beads (gifted by a member)

The second is my Fox Vulpis 5**
*- This is carried on my SAR kit if not using the Vic' RT*
*** This is a favourite of mine and would be my EDC if it wasn't for the current Vic Alox challenge*

- This is carried on my SAR kit if not using the Vic' RT*
-
@SurgeUk said:
Here are my two profferings, which given that Mrs Surge is a full on Italian, is pretty poor

First an Antonini Rescue Knife* (purchased from a member) wearing a set of Ranger Beads (gifted by a member)

The second is my Fox Vulpis 5**
*- This is carried on my SAR kit if not using the Vic' RT*
*** This is a favourite of mine and would be my EDC if it wasn't for the current Vic Alox challenge*
Nice! Very, very nice!
Lähetetty minun SM-T515 laitteesta Tapatalkilla
- This is carried on my SAR kit if not using the Vic' RT*
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login