SAK-A-Like and/or off brand challenge for December?
-
Ok, 4 days late and a dollar short:
DAY 1
Carried the Armbars (OG) today but didn't see any action. Rheumatologist appt and some shopping. Should have used the Armbar to cut my wife's sandwich for lunch but said she wanted a real knife (sorry Armbar).

Sent from my SM-G996U using Tapatalk
-
<u>Day 5</u>
My SAK-A-Like got some work in today. It helped me assemble my daughter's longboard. The awl pushed through the grip tape so the bolts could go in, and the wrench held on to the nuts while I screwed the bolts in. I wonder if it will also be able to help me cut the wrapping paper...

-
Day 5
I’m pleased to report that the bottle opener on the Vulpis performed its function well.
It seemed slightly persnickety about the angle of approach to the bottle cap being just right, but I feel like this is fairly common for MT bottle openers. Once the angle was correct, it removed the bottle cap in one smooth motion.
The bottle opener also has a slightly larger flathead screwdriver on the end, which will be addressed in a future post.

-
Day 2
Used the Armbar to help separate poorly perforated signs and cut tape without a dispenser to hang them for Ad break today. When life gives you lemons, use the Armbar because I've got lemons and they didn't help.

Sent from my SM-G996U using Tapatalk
-
Day 6
Wore this goofy Christmas suit to work today, and didn't carry the T4 due to tiny pockets. Thought it would be a no use day, but found a loose thread on the suit when I was putting it away. Scissors took care of it.

-
Day 5
SAK-Alike Challenge
Leatherman Free T2The T2 got used for some package opening,,,, and I used the flathead to do some light prying,,,, but never did get any action pictures.

-
Day 6
The Vulpis has two flat screwdrivers: a smaller one on the tip of the can opener and a slightly larger one on the tip of the bottle opener. Both are beveled.
The one on the tip of the Vulpis can opener is slightly larger than the screwdriver on the Vic can opener, and appears to be sized for #2 Philips screws.
I’m unsure what the sizing criteria were for the larger driver, but it is considerably smaller than the Vic large screwdriver.
While I feel this set of screwdrivers is less versatile than the standard Vic opener layer, they had no trouble turning any screws that they fit.



-
<u>Day 6</u>
Just some light duty snack opening today.

-
Noce pics so far.
-
Day 3
Work didn't give me anything to use the Armbar with today

Sent from my SM-G996U using Tapatalk
-
Day 7
This dollar store Christmas light headband was being a little flaky. Saw a screw on it and figure I'd see if I could spot a loose wire or anything fixable. I had my doubts but the awl-driver handled it fine. Gave it the ol' wriggle and everything seems fine now.

-
Day 6
SAK-Alike Challenge
Leatherman Free T2De-burring some cuts I made in a piece of Lexan at work today.

-
<u>Day 7</u>
Had package duty again, as I foresaw.

I knew I was taking a gamble getting the SwissQlip as I had heard positive and negative reviews but I am actually disappointed with it. I felt they could've put a bit more effort into it as it can block some back tools, and it can make the layer tool difficult to open. I thought about returning it but I'm thinking of trying to mod it a bit or perhaps use it to model something up for my 3D printer and see if I can make it better for my purposes. I like the idea, it just needs better execution.
-
Day 4
Used Armbar to cut up my pork chop for lunch

Sent from my SM-G996U using Tapatalk
-
Day 7
SAK-Alike Challenge
Leatherman Free T2Today was my day off,,, nothing much going on other than a couple of doctor's appointments. I also picked up some sockets for a winter motorcycle project.

-
Day 7
The saw typically isn’t one of my most frequently used implements on any of my SAKs or MTs, but to give a fair evaluation I was determined to test out the saw on the Vulpis.
As shown, the saw did manage to cut wood. However it was slow and awkward and I’m not sure it is worthwhile. The short saw blade necessitated short strokes, and limits the size of wood that can be cut (probably to smaller than the size I could just break without a tool).
The short handle, which I can’t get more than three fingers on in any grip, essentially became only a two-finger handle when holding it at an angle and with my ring finger behind the end of the tool to keep my fingers from slipping forward onto the saw blade on the forward stroke.
So, while the saw technically did cut wood, the size and ergonomics are such that I don’t believe it worth having.


-
Day 8
Having carried and used the Vulpis for about a week, having used or attempted to use every implement on it, and preparing to switch to a different SAK-alike tomorrow, here are my final (for now) thoughts on the Vulpis…
The blade helped me free my new compressor and accessories from their packaging today. I’ve used it throughout the last week for numerous cigars, packages, fingernails, etc. In spite of its smallish size and odd shape, it is a good blade.
The screwdrivers are useful, if a bit oddly sized.
The bottle opener is adequate, though slightly fiddly to use.
The can opener will work in a pinch, but if I anticipated using it regularly I would choose a different SAK/MT.
The scissors really fell short of expectations. While they can manage to cut some things that are thick and rigid enough, they are nearly ineffective on things that are thin and flexible, such as hair or strings.
While the saw technically did cut wood, small size and poor ergonomics rendered it not a worthwhile function to have on this MT IMO.
When I originally purchased the Vulpis, I had high hopes that it might be like a FX made from premium materials, but it hasn’t really lived up to that. It is, however, an overall good quality piece with a few glaring issues with some of the functions. Accordingly, my advice to anyone considering purchasing a Vulpis is to get one of the two-layer versions with only the blade and opener layer. The scissors and or saw add weight and bulk, but not really useful functionality IMO.

-
<u>Day 8</u>
Got to cut some zipties off so I can setup some Christmas inflatables.

Also got to use the flat head to help me open another SAK-A-Like. It was definitely rusty and tight in there. I gave it a good wash and scrub, and then decided to oil the pivot points to help crack everything loose again. Going to soak each end in mineral oil over night to hopefully help it loosen up some more. It already has a decent snap when closing.



Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
