Leatherman Bond Owners Club
-
Welcome to the forum Mountain.

Just to prove the fact that you can ask a simple question and get multiple opinions I think I'd be just fine with that. :D If it's touching without binding badly then I really don't think it's a problem. Leatherman aim to make then as close as possible. If, on the other hand, it's actually hard to close then yeah, contact your retailer.
-
@amountainhigh said:
I noticed the wire-cutters catch each time I close the pliers - I can feel the resistanceI would be tempted to open and close them 20,000 times while watching a Teletubbies marathon. That would probably smooth them out a little.


-
@amountainhigh said:
Just picked up my first Leatherman today - a Bond (UK, no fixed blades etc). Out of the box I noticed the wire-cutters catch each time I close the pliers - I can feel the resistance and there’s a small mark on the wire-cutters where they catch (per the photo). Is this normal or should I look to swap it out at the retailer? Thanks in advance :)I have had same kind problems on my tools, one soltion is using file to smooth out that part where cutters catch ( need small preferably diamond file) or send it to retailer for tool swap.
Only Tools Matters
-
Had my Bond out for a bit of use today.

-
Great carry today Gareth.

-
-
Gareth- good combo, pairing a BOND and a Classic!
I do like the Yellow, is a bold look for the little carry.
-
Cheers all.

-
I Finally installed a saw on my Bond. I have to be a bit careful when closing it up, the pliers want to land on top of the saw a bit, but if I close that side first it works smoothly. I’d like it to be less janky but this is the best I could come up with without drastically changing the rest of the toolset.

-
Very nice that you got it to go on the same side as the knife blade :o adds a whole other dimension to the tool now

-
@Poncho65 said:
Very nice that you got it to go on the same side as the knife blade :o adds a whole other dimension to the tool now

Thanks, it was nearly the last place I tried and just happened to work

There’s actually just enough room for the saw to share that little ramp that the blade rests on to keep it from hitting the bottom of the handle well, so that was lucky.Now I’m thinking about swapping the the pliers out for ones on the Rebar

-
Got the pliers in!
I think I’ve finally got what I wanted; a more pocket friendly Rebar

-
Nice job! 😎
I am surprised you did not replace the file as well? I believe LM missed the boat on the BOND by not using the WAVE diamond file within the design.
I purchased a Surge blade pack (10$)and carry the diamond file in the pancake sheath to round out my tool needs in my day pack.
Also, surprised you have not added a pocket clip, that hole in the handle upsets my OCD that the tool is incomplete. 😁😉
-
@LoopCutter said:
Nice job! 😎I am surprised you did not replace the file as well? I believe LM missed the boat on the BOND by not using the WAVE diamond file within the design.
I purchased a Surge blade pack (10$)and carry the diamond file in the pancake sheath to round out my tool needs in my day pack.
Also, surprised you have not added a pocket clip, that hole in the handle upsets my OCD that the tool is incomplete. 😁😉
If I had a donor diamond file on hand I’d certainly add it! I like the one on the Wave, and probably use the diamond file more than the aggressive side. I’ll likely pick one up sooner or later.
I’ve thought about adding a pocket clip, but I also like how sleek the Bond is already and since I carry it loose in my back pocket I really don’t need it. Still, I might order one before summer since a clip might be better for shorts carry.
-
Besides the WAVE, I understand the PST II and Pulse models were fitted with the diamond style file.
I know my Pulse does, never owned a PSTII YET.
-
Great modding trichosirius!

Your picture reminded me I hadn’t posted a picture of my bond in this thread.
I wouldn’t say I have a love hate relationship with the bond. I just can’t seem to bond with the Bond. Early on, I thought that I could just change it to what I like. It first started off with swapping the blade for a serrated one from a Rebar. I am a clutz when I get in a hurry and slicing the web of my hand didn’t seem like a good idea. After that I filed the little nubs in the handle that would dig into my hand while operating the pliers. I tried swapping a charge bit driver in for the the #2 Philips bit. It works, but the pliers bind when closing. I used it like this for six months or so before I got fed up with it and threw it in the corner of my toolbox in the garage. A few months back I came upon a post in the Bond thread on BladeForums. In the post a member added the saw from a rebar and removed the lanyard ring on the clip side. So, I got out the wrenches and went to work. While I swapped back in the #2 Philips and saw, I also swapped the pliers from a Rebar. If I hadn’t already had the donor parts from a Rebar, I wouldn’t have gone to the effort to do this. I still prefer the PST to the Bond, even after the mods.
Quick note on the Rebar saw swap. The Rebar saw will sit proud of the handle when closed. I took a file and slowly took off material until it was flush with the handle. When it was to where I wanted it, I took some 220 grit sandpaper to smooth out the spline of the saw. After that was done, I disassembled and cleaned out the filings from the clip side and reassembled.
Sorry for the long winded post.
-
Quite excellent mod work by both of you

-
@JonesE said:
Great modding trichosirius!
Your picture reminded me I hadn’t posted a picture of my bond in this thread.
I wouldn’t say I have a love hate relationship with the bond. I just can’t seem to bond with the Bond. Early on, I thought that I could just change it to what I like. It first started off with swapping the blade for a serrated one from a Rebar. I am a clutz when I get in a hurry and slicing the web of my hand didn’t seem like a good idea. After that I filed the little nubs in the handle that would dig into my hand while operating the pliers. I tried swapping a charge bit driver in for the the #2 Philips bit. It works, but the pliers bind when closing. I used it like this for six months or so before I got fed up with it and threw it in the corner of my toolbox in the garage. A few months back I came upon a post in the Bond thread on BladeForums. In the post a member added the saw from a rebar and removed the lanyard ring on the clip side. So, I got out the wrenches and went to work. While I swapped back in the #2 Philips and saw, I also swapped the pliers from a Rebar. If I hadn’t already had the donor parts from a Rebar, I wouldn’t have gone to the effort to do this. I still prefer the PST to the Bond, even after the mods.
Quick note on the Rebar saw swap. The Rebar saw will sit proud of the handle when closed. I took a file and slowly took off material until it was flush with the handle. When it was to where I wanted it, I took some 220 grit sandpaper to smooth out the spline of the saw. After that was done, I disassembled and cleaned out the filings from the clip side and reassembled.
Sorry for the long winded post.
Looks awesome

I know what you mean about the file; while I really like the Bond, that thing can be a nuisance when using and opening and closing the tool. While I can avoid it, it can be a bit irritating since I’m so nitpicky with my tools.
I think I too would prefer the PST. I got the Bond precisely because I was in the market for a PST but couldn’t find a decent affordable one at the time, and the Bond was close enough.
To me the smaller the package the better, and the original just seems perfect the way it is. -
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
