Show off your Sak mod's!
-
Thanks awl!
-
Decided to do another Wenger mod yesterday. Wanted to incorporate their brushed stainless steel scales with clip point blades. Heavy little compact SAK,.



-
Very nice! Did you do anything to refresh the scales or are they original?
-
They were original and royal pain in the butt to remove. Plan on warping some outer liners if you try it. Externally in fantastic shape so I did not have to do much else.
-
@pa_strunk said:
Decided to do another Wenger mod yesterday. Wanted to incorporate their brushed stainless steel scales with clip point blades. Heavy little compact SAK,.Nice! Really like those clip point blades!
-
I did small mods on my Pioneer X, i filed blade edge to inside can opener to act as hook like package opener also bit improved phillips part so it goes bit deeper.
I have also shortened bit my awl so now its bit stronger and sharper. It may not look shsrp but it is.Mods are bit rough but both do their jobs and orginal purpose still stays.


Only Tools Matters
-
@Antti Lammi said:
I did small mods on my Pioneer X, i filed blade edge to inside can opener to act as hook like package opener also bit improved phillips part so it goes bit deeper.
I have also shortened bit my awl so now its bit stronger and sharper. It may not look shsrp but it is.Mods are bit rough but both do their jobs and orginal purpose still stays.


Only Tools Matters
Looks good Antti, I have done similar to one of my can openers, but more of a hook shape, pretty useful.
-
@Enginears said:
Looks good Antti, I have done similar to one of my can openers, but more of a hook shape, pretty useful.I first thinked that hook type but decided to make straight blade since i noticed its more useful for me.
Only Tools Matters
-
Lately I have been wanting to make mods that seem out of place and time. The fishing tool mod was one, wooden scales, bail, limited tools. On a similar thing I have had this one in my notebook for a while, but hadn’t quite figured out if it would be alox or not, or a 100mm. This one is the “buzzsaw gardener” :D like a buzzsaw trapper only a Vic gardener. Thicker handle, no back tools, just saw and blade. I wanted to go brass liner but got too impatient to wait for the material.
[attach id=0 msg=2468950]
[attach id=1 msg=2468950] [attach id=2 msg=2468950]


-
@Enginears said:
Lately I have been wanting to make mods that seem out of place and time. The fishing tool mod was one, wooden scales, bail, limited tools. On a similar thing I have had this one in my notebook for a while, but hadn’t quite figured out if it would be alox or not, or a 100mm. This one is the “buzzsaw gardener” :D like a buzzsaw trapper only a Vic gardener. Thicker handle, no back tools, just saw and blade. I wanted to go brass liner but got too impatient to wait for the material.
[attach id=0 msg=2468950]
[attach id=1 msg=2468950] [attach id=2 msg=2468950]Nice mod
Only Tools Matters
-
After my last mod I successfully assembled some spare leftovers into a Spartan as I didn't have one already, went well. However, as I intended I moved on to attempt a Yeoman mod. Ive managed to assemble it, but the combo tool very slightly catches/rubs on the main blade, which is rather annoying. Ive checked 2 other SAKs with Combo tool, 1 clears it, the other (a very old Compact with no file on the hook) rubs a very small amount. Im wondering what the cause might be - my guess is poor peening during assembly. Annoyingly the peening on the Spartan went really well but was more troublesome on the Yeoman. Anyone able to confirm my suspicions? (or offer alternative explanation)
Cheers!
-
Are you certain the peening is tight enough on both tools? Sometimes the blade needs a few extra taps to move it fully over in my experience. Also using the older thicker blade makes the rubbing more likely.
That said, I once bought a waiter that has the two tools rubbing more than I like and it was stock from the factory. Never did figure a specific culprit.
-
First post. The community inspires! Could not find anything online about making a SAK scale tool nail file to fit in the slots. I am making one from a 58 mm sak copy. Removed the file (x design on one side and the 2 thin lines on the other). It’s cut and filed to fit. It needs the nail pull still. Thinking about a mold with jb weld that can be filed to shape. I would love your thoughts and ideas. My photo seemed too large to post.
-
@Tinker88 said:
First post. The community inspires! Could not find anything online about making a SAK scale tool nail file to fit in the slots. I am making one from a 58 mm sak copy. Removed the file (x design on one side and the 2 thin lines on the other). It’s cut and filed to fit. It needs the nail pull still. Thinking about a mold with jb weld that can be filed to shape. I would love your thoughts and ideas. My photo seemed too large to post.Hey Tinker, welcome. Yes the community here is great and in this thread alone is a tome of great mods going back years. I have not made a file to fit in the slot as you describe, but I did a file scale tool once and to make the nail pull I used a piece of a scale super glued to the end of the file. This may be quicker and easier than the JB weld, although that sounds like it would work too. If you go back through my post attachments there are some pics of the scale file I made.
-
Made some tweaks to blade shape on my compact modeler. [attach id=0 msg=2472526]

-
Saw a mod like this on eBay a while back and had to give it a try. The GAK2 wood saw, can/bottle-opener, file is not the most practical combo tool on a 108 mm. Shortening for a 93 mm probably even makes less sense, but I just had to do it if for no other reason but to watch my friends face when I offer it to them to open beer bottles.




-
I was having a rummage through one of my boxes of SAK parts looking to see if I had a suitable blade to repair an old knife and got distracted by a load of 74mm parts.
A couple of hours actual work and about 8 waiting on epoxy curing and here's a single layer Bladeless Executive with horn scales and brass bolsters.yes there are still scratches but I think that brass&horn scales look better when they appear to have lived a full life. To further this appearance it will be riding in my pocket with a bunch of keys and handful of loose change for a while. Also need to age and tarnish that brass a bit with salt and vinegar.




-
Excellent PTRSAK, I really like the look. I bet the brass will get a real nice patina with a few weeks use.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
