Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Repaired Grappler

Scheduled Pinned Locked Moved Gerber Tools
22 Posts 1 Posters 2.6k Views
  1. Home
  2. Tool Talk
  3. Gerber Tools
  4. Repaired Grappler
Repaired Grappler
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • Trilby Offline
    Trilby
    Posts: 32
    Trilby Offline
    Trilby
    wrote on last edited by Trilby
    #11 Quote Reply

      This is the shoddy Part modeled in 3D, ready to be printed/sintered. Note that this mixes Gen1/2 and requires shortening the AdjustmentScrew quite a Bit (just like in Gen2). Forum does not allow arcane Attachments .. so rename *.stl.doc to *.stl. Sizes in mm. Make sure to look around for resonable Offers. Here in Germany i can get this in Titanium for 100$

      GrapplerAdjuster20.jpg

      📎 GrapplerAdjust20.stl.doc

      1 Reply Last reply
      • Barry Rowland Offline
        Barry Rowland
        Posts: 31,387
        Barry Rowland Offline
        Barry Rowland
        wrote on last edited by
        #12 Quote Reply

          I forgot about the Grappler! The used ones are mighty salty on the used market :facepalm:

          1 Reply Last reply
          • Trilby Offline
            Trilby
            Posts: 32
            Trilby Offline
            Trilby
            wrote on last edited by
            #13 Quote Reply

              Some minor but important Refinements to the 3D-File. Again, rename *.stl.doc to *.stl

              📎 GrapplerAdjust21.stl.doc

              1 Reply Last reply
              • IMR4198 Offline
                IMR4198
                Posts: 6,451
                IMR4198 Offline
                IMR4198
                wrote on last edited by
                #14 Quote Reply

                  Trilby, I think you are the Grappler expert. I didn't realize the prices of these things on the secondhand market until Barry mentioned it. Wowsers. Best wishes. G
                  :)

                  1 Reply Last reply
                  • Trilby Offline
                    Trilby
                    Posts: 32
                    Trilby Offline
                    Trilby
                    wrote on last edited by
                    #15 Quote Reply

                      Again some minor Refinements ..
                      Rename *stl.doc to *.stl

                      📎 GrapplerAdjust22.stl.doc

                      1 Reply Last reply
                      • Trilby Offline
                        Trilby
                        Posts: 32
                        Trilby Offline
                        Trilby
                        wrote on last edited by
                        #16 Quote Reply

                          Optional v24 with added 2.5mm Hole for a M3x3mm SetScrew to retain the PivotAxle (needs to get threaded) ( M3x4mm will also work)

                          You can preview these in 3D at https://www.thingiverse.com/thing:6652755

                          If You do not need this extra SetScrew, use v22 above

                          Rename *.stl.doc to *stl

                          📎 grappler24.stl.doc

                          1 Reply Last reply
                          • Trilby Offline
                            Trilby
                            Posts: 32
                            Trilby Offline
                            Trilby
                            wrote on last edited by
                            #17 Quote Reply

                              V25 w. smoothed AxleBore from 32 to 320 Faces.
                              V26 likewise plus the extra 2.5mm Bore for optional RetentionScrew (Thread for M3. M3x3 or M3x4 will fit)
                              Preview in 3D on https://www.thingiverse.com/thing:6652755
                              Rename *.stl.doc to *.stl

                              📎 grappler25.stl.doc

                              📎 grappler26.stl.doc

                              1 Reply Last reply
                              • Trilby Offline
                                Trilby
                                Posts: 32
                                Trilby Offline
                                Trilby
                                wrote on last edited by
                                #18 Quote Reply

                                  Freshly printed from Steel in CN. Replaces the broken Part just fine

                                  GrapplerAdjNew.jpg

                                  1 Reply Last reply
                                  • Trilby Offline
                                    Trilby
                                    Posts: 32
                                    Trilby Offline
                                    Trilby
                                    wrote on last edited by Trilby
                                    #19 Quote Reply

                                      Requires only very little FineTuning with a small File. And the small Clearance Hole at the Side could be larger. Use DieGrinder or 4mm HSS Drill to bevel it a Bit

                                      1 Reply Last reply
                                      • Trilby Offline
                                        Trilby
                                        Posts: 32
                                        Trilby Offline
                                        Trilby
                                        wrote on last edited by
                                        #20 Quote Reply

                                          Old vs. New

                                          AdjusterNewCN2.jpg

                                          1 Reply Last reply
                                          • Barry Rowland Offline
                                            Barry Rowland
                                            Posts: 31,387
                                            Barry Rowland Offline
                                            Barry Rowland
                                            wrote on last edited by
                                            #21 Quote Reply

                                              Great job!!

                                              1 Reply Last reply

                                              Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                              Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                              With your input, this post could be even better 💗

                                              Register Login

                                              • 1
                                              • 2
                                              1. Home
                                              2. Tool Talk
                                              3. Gerber Tools
                                              4. Repaired Grappler
                                              Reply
                                              • Reply as topic
                                              Log in to reply
                                              COMMUNITY LINKS
                                              EDC-TV SAKWiki GearFeed SAKSelector
                                              Operational Funds

                                              Help us keep the Unworkable working!

                                              Make A Donation
                                              November Goal: $300.00
                                              Due Date: Nov 30
                                              Total Receipts: $0.00
                                              Below Goal: $300.00
                                              0% funded
                                              • Login

                                              • Don't have an account? Register

                                              • Login or register to search.
                                              • First post
                                                Last post
                                              0