The December 2024 Utility Knife Challenge
-
@ReamerPunch said:
I hope AzteCypher does not mind me jumping in.
I like the black and the blue.The black and top blue are nice.
Some of them looks like a Mt Fuji badge when it is small
-
I did the badges at work. But don't tell anyone.

Day 11
Engineer PZ-58KN in limited blue!

Goes nicely with the orange.And the Gerber EAB. Probably the best, most rugged mini folding utility knife.

-
Day 10
No use today.
Losing with my cap.
[attach id=0 msg=2508120]

-
-
Day 11
I slid this unmarked box cutter in my shirt pocket this morning and used it to open bags of mulch.


-
<u>Day 10</u>
Playing catch up.
Using the EAB to remove the stitches on a pocket from my new coat for my sister-in-law's upcoming wedding.

-
<u>Day 11</u>
Using the EAB to open up a bag of sweet treats. The holidays are harder for me since everyone's baking cookies, cakes, and pies, and I have a bad sweet tooth.

-
-
Day 11
No blade action today.
With lull, I opened the handle to examine my spare blade. Since it is a wharncliff shape I swapped blades.
[attach id=0 msg=2508199]
[attach id=1 msg=2508199]
[attach id=2 msg=2508199]


-
@cody6268: I think I see a First Gear fire engine on the shelf!

@BPRoberts: I also passed a Rebar on to a new owner...but it's been largely replaced by an ST300.
@kaevin: the A-1000RP looks pretty good!
@ReamerPunch: sweet pliers!
@Alan K: I have a similar cutter that'll make an appearance before the challenge ends.
@AzteCypher: I bet those are good!
@JonesE: quiet days are fine by me!
@LoopCutter: that black oxide PST...

Day 11
The first round of compare and contrast got underway this evening. Our test subject is receipt paper. The Stanley blade did a good job, but the DeWalt did even better. I was expecting them to be evenly matched, so the end result was a bit of a surprise.
[attach id=0 msg=2508215]
Utility knife record: 8-0.
Stanley record: 0-1.
DeWalt record: 1-0.
-
I've debated carrying the ST300 after I did the Powerlock last month. It's not impossible in the pants I wear to work most days, but the Rebar is about 99% as capable for the stuff I need and much more comfortable in the pocket.
**Day 11:
**Been enjoying my Sharpmaker and decided to get the CBN rods to help make it easier to restore some really dull knives I have sitting around. Older ones that either went unsharpened for years or, in some cases, were sharpened so badly they would've been better off without. Lockdown assisted with packaging.

-
Day 12
OLFA LTD-04
[attach id=0 msg=2508220]OLFA and NT cutter are two of the bigger brand of Japanese cutters. For some reason I don't like to get OLFA they usually features more stubby/squarish design. But they are high quality, on par, if not better than NT cutters.
This OLFA LTD-04 is a "limited edition" (LTDs are limited of their best sellers/classics) of 191-B and PA-2 difference being color. They are the OLFA auto reload A sized light duty cutters (they also make L sized MZ-AL 168B and PL-1). The body is mostly made with high quality plastic with some metal rails, spring plates and part of the slider. It comes with the "excel blade" ultra sharp black blade.
[attach id=1 msg=2508220]
The back, including a detailed instruction label.[attach id=2 msg=2508220]
The cutter itself doesn't seem to be easy to take apart. The tip features similar "bend" feature like the A-500RP and A-1000-RP to stabilize the blade.To change draw a new blade, push the slider all the way out...
[attach id=3 msg=2508220]



-
... and pull the used blade out.
[attach id=0 msg=2508221]And then pull the slider all the way back, the spring plate in the compartment back will push a new blade to the slider.
To load the blade compartment with extra blades, flip over to the back and push the push button at the end and pull the part around the push button away from the tip, compartment will pushed open by the spring plate.
[attach id=1 msg=2508221]Then put the blade inside the compartment, maximum number of blades is 5, making it a 5+1 cutter.
[attach id=2 msg=2508221]Then just push the back plate back and slide the end part back towards the tip.
The whole back plate spring with the swinging back part really similar to film camera. This is a very interesting design.
In summery, this LTD-04/PA1 is a high quality auto reload light duty cutter. It has plastic handle but does not feel cheap. It is comfortable to hold. The outlook is retro or too stubby/squarish, depending on how you view it. Some actually thinks it is cute. The loading mechanizing is fun and interesting. Which gives you a "reload the film camera" ritual. For the price one may want to have a full metal cutter, but due to the number of parts and complexity, it is harder to make all parts with metal, and the weight will be much heavier.. A500/A1000 loading is less hassle. However, the LTD-04/PA-1 auto lock is more powerful (deeper teeth). If you are after collecting "Stuffs with interesting mechanism" or "like to fiddle with something" you may find this interesting.
[attach id=3 msg=2508221]
My companions today for studying and job seeking.



-
@Farmer X said:
@cody6268: I think I see a First Gear fire engine on the shelf!
Thanks!
I found it a few years back for less than $20 shipped. First Gear has made some nice stuff, but it's often priced dearly--the IH Durastar ambulance often brings $150-$200, and other fire rigs usually north of $50--particularly the Macks. Seems the Shell stuff was overproduced, and it often goes for much cheaper than actual departments or more popular special series.
It's an International R-190 issued in the Shell series back in 1994. It's lettered as being a plant protection rig for a Houston refinery. I found an old $75 price sticker rattling around in the box--I suspect that the previous owner probably paid that.
[attach id=0 msg=2508224]
[attach id=1 msg=2508224]


-
Day 12
Coin delivery with the EAB.

-
Day 10:
Those easy-pull seals quite often aren't--so I end up just slitting them and then pulling them out.
[attach id=0 msg=2508226]

-
@ReamerPunch said:
Day 12Coin delivery with the EAB.
Nice!
Several years ago, someone liquidated a coin collection by putting them in a vending machine at a local dollar store. I ended up getting coins from all over the world that likely weren't even worth the quarter I paid, but still, it was an neat find.
Then there was that '60s French Franc coin the bank gave me in the place of a nickel. Really need to get around to making a display for those foreign coins.
-
@ReamerPunch said:
Day 12Coin delivery with the EAB.
Metal meeting metal.

-
Those easy-pull seals quite often aren't--so I end up just slitting them and then pulling them out.
[attach id=0 msg=2508226]
My wife hates it when I open any food packages with a utility cutter/knife. Suppose the blade has some kind of lub or oil to keep it from rusting and she doesn't like any to have a slightest of chance to get to our food.
That's when I pull out a stainless steel blade cutter.

I cut my food with any cutter regardless of blade material

-
More Day 12
Christmas shopping.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
