The December 2024 Utility Knife Challenge
-
I've debated carrying the ST300 after I did the Powerlock last month. It's not impossible in the pants I wear to work most days, but the Rebar is about 99% as capable for the stuff I need and much more comfortable in the pocket.
**Day 11:
**Been enjoying my Sharpmaker and decided to get the CBN rods to help make it easier to restore some really dull knives I have sitting around. Older ones that either went unsharpened for years or, in some cases, were sharpened so badly they would've been better off without. Lockdown assisted with packaging.

-
Day 12
OLFA LTD-04
[attach id=0 msg=2508220]OLFA and NT cutter are two of the bigger brand of Japanese cutters. For some reason I don't like to get OLFA they usually features more stubby/squarish design. But they are high quality, on par, if not better than NT cutters.
This OLFA LTD-04 is a "limited edition" (LTDs are limited of their best sellers/classics) of 191-B and PA-2 difference being color. They are the OLFA auto reload A sized light duty cutters (they also make L sized MZ-AL 168B and PL-1). The body is mostly made with high quality plastic with some metal rails, spring plates and part of the slider. It comes with the "excel blade" ultra sharp black blade.
[attach id=1 msg=2508220]
The back, including a detailed instruction label.[attach id=2 msg=2508220]
The cutter itself doesn't seem to be easy to take apart. The tip features similar "bend" feature like the A-500RP and A-1000-RP to stabilize the blade.To change draw a new blade, push the slider all the way out...
[attach id=3 msg=2508220]



-
... and pull the used blade out.
[attach id=0 msg=2508221]And then pull the slider all the way back, the spring plate in the compartment back will push a new blade to the slider.
To load the blade compartment with extra blades, flip over to the back and push the push button at the end and pull the part around the push button away from the tip, compartment will pushed open by the spring plate.
[attach id=1 msg=2508221]Then put the blade inside the compartment, maximum number of blades is 5, making it a 5+1 cutter.
[attach id=2 msg=2508221]Then just push the back plate back and slide the end part back towards the tip.
The whole back plate spring with the swinging back part really similar to film camera. This is a very interesting design.
In summery, this LTD-04/PA1 is a high quality auto reload light duty cutter. It has plastic handle but does not feel cheap. It is comfortable to hold. The outlook is retro or too stubby/squarish, depending on how you view it. Some actually thinks it is cute. The loading mechanizing is fun and interesting. Which gives you a "reload the film camera" ritual. For the price one may want to have a full metal cutter, but due to the number of parts and complexity, it is harder to make all parts with metal, and the weight will be much heavier.. A500/A1000 loading is less hassle. However, the LTD-04/PA-1 auto lock is more powerful (deeper teeth). If you are after collecting "Stuffs with interesting mechanism" or "like to fiddle with something" you may find this interesting.
[attach id=3 msg=2508221]
My companions today for studying and job seeking.



-
@Farmer X said:
@cody6268: I think I see a First Gear fire engine on the shelf!
Thanks!
I found it a few years back for less than $20 shipped. First Gear has made some nice stuff, but it's often priced dearly--the IH Durastar ambulance often brings $150-$200, and other fire rigs usually north of $50--particularly the Macks. Seems the Shell stuff was overproduced, and it often goes for much cheaper than actual departments or more popular special series.
It's an International R-190 issued in the Shell series back in 1994. It's lettered as being a plant protection rig for a Houston refinery. I found an old $75 price sticker rattling around in the box--I suspect that the previous owner probably paid that.
[attach id=0 msg=2508224]
[attach id=1 msg=2508224]


-
Day 12
Coin delivery with the EAB.

-
Day 10:
Those easy-pull seals quite often aren't--so I end up just slitting them and then pulling them out.
[attach id=0 msg=2508226]

-
@ReamerPunch said:
Day 12Coin delivery with the EAB.
Nice!
Several years ago, someone liquidated a coin collection by putting them in a vending machine at a local dollar store. I ended up getting coins from all over the world that likely weren't even worth the quarter I paid, but still, it was an neat find.
Then there was that '60s French Franc coin the bank gave me in the place of a nickel. Really need to get around to making a display for those foreign coins.
-
@ReamerPunch said:
Day 12Coin delivery with the EAB.
Metal meeting metal.

-
Those easy-pull seals quite often aren't--so I end up just slitting them and then pulling them out.
[attach id=0 msg=2508226]
My wife hates it when I open any food packages with a utility cutter/knife. Suppose the blade has some kind of lub or oil to keep it from rusting and she doesn't like any to have a slightest of chance to get to our food.
That's when I pull out a stainless steel blade cutter.

I cut my food with any cutter regardless of blade material

-
More Day 12
Christmas shopping.

-
Day 12
Carried but not used.

-
Day 11:
Chose a knife a bit out of the ordinary--the Valet Auto Strop Razor Utility knife advertising Cudahy Packing Co. Kind of a multitool as well, as it has a tape slitter and cigar cutter built in. also weighs near nothing and is paper-thin.
If I'm not mistaken, it's one of the first utility knives ever marketed. It takes a single-edge razor blade WITHOUT the reinforcement. These were marketed as a way to get more use out of blades too dull to shave with. Finding replacement blades isn't easy. A few companies (i.e. Feather) do, but they're hard to find. Besides, I think the included blade was the original Valet, so I've left it in as to preserve it. I sharpened it up to the best of my abilities. Whatever steel Valet used was amazing stuff.
I'm not exactly sure of age. The Auto-Strop line was produced between 1901-1946. The "Auto Strop Razor" trademark was first used in 1919, and the company had a merger with Gillette in 1930. So, there's a good chance this is 100 years old.
And the company advertised. They were, at one point, huge. Heck, they were one of the first S&P 500.
[attach id=0 msg=2508276]

-
@BPRoberts: the ST300 is probably better suited to my work uniform. And how well does the Sharpmaker work for you?
@kaevin: blade replacement seems a little fiddly. But the OLFA looks pretty neat!
@ReamerPunch: a cool and interesting group of coins! (I could probably send a few American ones if you'd like.)
@cody6268: I've had a few of those seals that didn't work as promised. They're a decent enough idea that was horribly executed.
@Alan K: no worries about lack of use. Great shot!
Day 12
Paracord is another challenge staple for me.
[attach id=0 msg=2508277]
Both blades cut the paracord in one pass. They did better the farther I got from the tip. The Stanley cut slightly easier and neater.
[attach id=1 msg=2508277]
Utility knife record: 9-0.
Stanley record: 1-1.
DeWalt record: 1-1..jpg)
.jpg)
-
Cody, I've been shaving with safety razors for years, and to think I've been throwing the blades away when they got too dull to shave with. That tool seems like a great idea and I'm now going to have to hunt one up. How does it retain the blades? Safety razor blades are available on Amazon for as low as 100 for 10 bucks (or less sometimes) by the way.

-
The Sharpmaker is great at taking knives with intact, but dull, edges and making them very sharp. It is not as great with damaged or non-existent edges. I'm hoping the new stone will help with that. Thus far, I've had great success with using a coarse diamond stone to put a basic edge on when needed and then finishing with the Sharpmaker.
I like that it is more or less idiot proof (I am a passable, but not great, freehand sharpener), but the real reason I got it over a Lanksy or something is that it has the appropriate tools and instructions to sharpen basically anything. I've done knives, kitchen gadgets, scissors, and all sorts of things on it. Plain edge, serrated, 50/50, doesn't matter. If I only wanted to do knives, I think I'd be better off continuing to practice freehand sharpening and putting the money towards nicer stones. But being able to bring a potato peeler back from the dead and keep using it instead of replacing it AND also easily do the final sharpening on my knives is a great combo.
Day 12
How do all the people who don't carry pocket knives drink their coffee with these tiny vent holes?

-
-
@Farmer X said:
@ReamerPunch: a cool and interesting group of coins! (I could probably send a few American ones if you'd like.)I've got a bunch of American coins. Even dollars and half dollars. They're great!

-
Chose a knife a bit out of the ordinary--the Valet Auto Strop Razor Utility knife advertising Cudahy Packing Co. Kind of a multitool as well, as it has a tape slitter and cigar cutter built in. also weighs near nothing and is paper-thin.
If I'm not mistaken, it's one of the first utility knives ever marketed. It takes a single-edge razor blade WITHOUT the reinforcement. These were marketed as a way to get more use out of blades too dull to shave with. Finding replacement blades isn't easy. A few companies (i.e. Feather) do, but they're hard to find. Besides, I think the included blade was the original Valet, so I've left it in as to preserve it. I sharpened it up to the best of my abilities. Whatever steel Valet used was amazing stuff.
I'm not exactly sure of age. The Auto-Strop line was produced between 1901-1946. The "Auto Strop Razor" trademark was first used in 1919, and the company had a merger with Gillette in 1930. So, there's a good chance this is 100 years old.
And the company advertised. They were, at one point, huge. Heck, they were one of the first S&P 500.
[attach id=0 msg=2508276]
Love this. I have been using DE blades, I think there are similar knife that loads DE blades. Always want to get hold of one of those.
-
Day 13
Tajima DCL500AYCL (L500 DCL and AYCL are color model and color code).
As seen from my collection, I seldom buy (if any) L size cutters. But since recently moving and also doing this challenge, I come to revisit the only L-size cutter I owned. It is a Chinese brand plastic handle (with metal rail). I have only used it a few times and I frown every time. So I got this Tajima (Japanese brand Chinese made).
[attach id=0 msg=2508295]
New in the box[attach id=1 msg=2508295]
Opened the box with the old L size, side by side[attach id=2 msg=2508295]
Front[attach id=3 msg=2508295]
BackAfter unboxing, before use, a plastic film on top of the blade needs to be pulled and remove. It actually is used to keep a few drops of oil between the blade and itself to keep the blade from rusting before it is sold.
The body is made with light smooth plastic. And it is covered on the edge as well as the back, making it very ergonomic to hold. This particular color way is a sharp neon yellow green or similar to Oakley retina burn (if you own a pair of Oakley you know what it is).




-
Continue
The main special feature is the slotted driver edge at the tip. Tajima claims they have heat treat to harden it for multiple uses, e.g. as a slotted driver, opening cans of pains, and cutting card board or tapes.
[attach id=0 msg=2508296]There is also a hole in the metal part of the body for attaching lanyard. The main target for this cutter is renovation workers or construction workers who needs to cut wires, tapes, opening paint cans, tightening screws etc. And it is why the slider features a big circle recess and the curved lines on it for adding traction when used with a glove. Lanyard is also important when they work from height or on a ladder. And this model does not have any build in snapper and assumes the user will carry around a plier at the same time.
[attach id=1 msg=2508296]
Front of parts[attach id=2 msg=2508296]
Back of partsThe blade it comes with is a "black blade" as well. They claim it uses Japanese tampering technique (that screams to me it isn't made in Japan) and is "rock hard" with multi-step sharpening.
This model is auto lock without any screw lock in the front. It also does not have any stabilization feature for stabilizing the blade tip. By no means it is meant for precision work, but rather a versatile cutting tool for use in the field. Tajima also made a similar newer model with a "fin" at the end of the body (Dora Fin). But I think that will get in the way when pocketing it so I opted for this one instead. I am very happy to replace the old Chinese branded cutter with this one although I seldom do any heavy work. Most likely it will be used for opening cans, sealant or liquid nails, for which I don't want to make my better blade messy and A-size light duty cutter will not be tough enough for the job.



Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
