The December 2024 Utility Knife Challenge
-
Great save Kaevin. Looks like your son will be enjoying his car again.
JonesE
-
Day 16
My auto-retracting blade doing what it does best.

-
Day 16
Rainy and Gloomy here today.
A landscape backdrop selected to enhance things that cut.
The Stanley takes center stage with two other favorites.
[attach id=0 msg=2508663]

-
Day 16
More package opening with the Green Beast.


-
<u>Day 15 - Catch up</u>
Used the EAB to open up dinner last night.

-
<u>Day 16</u>
Mail call and package duty today. Nothing special unfortunately.


-
This is my submission for the utility badge. Unfortunately it doesn't match up with Farmer X's design idea as I feel that ReamerPunch executed it perfectly. But, I do enjoy designing these so here are my ideas, though I realized now I didn't do one in black.



-
Day 16
Kinda skeptical about this one, the Prybrid X. It's nearly the size of a 91mm SAK but, even charitably, has like half the tools. On the Lockdown's the small xacto blade was a way to cram the blade into less space, and is complimented by a full sized "regular" knife. But I don't think the space savings here are worth it being the only blade. I'm a little skeptical of the pry function's durability as well.
Still, it did do the one thing I asked today, cut tape, and it is OHO, so that's something.

-
-
It was a gloomy day here, too. And a big thanks to AzteCypher for his badge design! We'll start the official vote tomorrow. And y'awl are doing great, as usual!

Day 16
I'm utterly spent and drained (turns out I cranked the thermostat up a little too much). This is all I have the energy for tonight. Regular MTo'ing should resume tomorrow.
[attach id=0 msg=2508707]
Utility knife record: 11-0.
Stanley record: 1-3.
DeWalt record: 3-1.
-
Day 15: Not a lot going on...
[attach id=0 msg=2508711]

-
@AzteCypher said:
This is my submission for the utility badge. Unfortunately it doesn't match up with Farmer X's design idea as I feel that ReamerPunch executed it perfectly. But, I do enjoy designing these so here are my ideas, though I realized now I didn't do one in black.



I am very sorry to have jumped in after Farmer X asked you to design the badge. I was at work and bored and I thought I could save you the trouble.
But you did a great job.
Day 17
I really like this one:

-
Also got an Engineer PZ-58 in limited black.


-
@ReamerPunch said:
Also got an Engineer PZ-58 in limited black.
Glad to know I am not the only one bitten by a plier bug.
-
@ReamerPunch said:
I am very sorry to have jumped in after Farmer X asked you to design the badge. I was at work and bored and I thought I could save you the trouble.
But you did a great job.
Day 17
I really like this one:
I have samekind utility knife ( Stanley 99E), but only drawback on this model is that you need to unscrew it to change blade but you can store blades in it
-
Day 17
Toughbuilt 5-in-1 Folding Utility Knife TB-H4-12-IM
[attach id=0 msg=2508736]
Front, the plate is plastic[attach id=1 msg=2508736]
Back with clip, the plate is metal (steel?)I got this TB utility knife a few months ago. It is very capable and solid. It is mostly made from metal, with one side being high quality plastic. The paint is beat up on mine, and I have replaced the original double ended bit with a vessel one (65mm) and grinded down the slotted side to make it 60mm.
[attach id=2 msg=2508736]
Blade (original) having touched up with a diamond file on one side after dulled. The blade only lock closed and fully openedIt includes a blade (with wire cutter notch), a bit holder with magnet that can accommodate up to 60mm long bit when folded, including a double end PH2 and slotted and a pry bar. It also includes a metal clip on the back, and a blade storage for 2 blades with magnet.
[attach id=3 msg=2508736]
Bit driver is centered, which is a huge plus over the Milwaukee and alike. It only locks closed or fully opened, would be great if it can lock at 90 degree. Be careful if you intend to use it with a bit extender, if it is a normal full "hex" extender, I have had the magnet attracted to it and pulled out when remove the extender. No issue if you use a smaller one like the Leatherman (ratchet) extender. You can also pull it out, epoxy and put it back as well.



-
Continue
[attach id=0 msg=2508738]
The pryer is press-and-slided. Beside prying things, I use it to press lift buttons sometimes.[attach id=1 msg=2508738]
The blade storage, there is a magnet to keep the blade from falling out.[attach id=2 msg=2508738]
Everything opened and pulled out


-
Continue
Some attempt at taking it apart
[attach id=0 msg=2508739]
[attach id=1 msg=2508739]I wanted to take the bit holder part out and put one extra notch to make it locks at 90 degree, but never finish the attempt.
[attach id=2 msg=2508739]
When it was new...


-
Continue
I am very happy with this TB-H4-12-IM. It is tough as its name with just enough function I need most of the time, pairing up with a Knipex Cobra 125. If I need to take things down I can pair this duo with a bit kit and a Surge with LM extender. Then I will have 2 drivers and 2 pliers. Fit nicely in a small pouch.


-
@ReamerPunch said:
I am very sorry to have jumped in after Farmer X asked you to design the badge. I was at work and bored and I thought I could save you the trouble.
But you did a great job.
Day 17
I really like this one:
No apologies necessary at all. I contemplated telling Farmer that he should go with your design but I did say i would design something. Plus I was at work, and it was a slow day yesterday so...

I do like your real life rendition!

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
