The December 2024 Utility Knife Challenge
-
With apologies for two consecutive posts, it is now time to put the badge design to a vote. Do my fellow challengers prefer those designed by AzteCypher or ReamerPunch?
-
Day 17
[attach id=0 msg=2508837]
New sheepfoot blade arrived for Stanley 10-049

-
Day 18
Hao Feng Li HFL-221
[attach id=0 msg=2508843]
Front[attach id=1 msg=2508843]
BackI have already shown all the better quality cutters/utility knives. So this time the subject is this first L-size cutter I got, possibly left behind by workers at my home.
It is typical Cheap-Chinese quality. It works (to a certain degree), and it's cheap. The body has a metal rail, which has it's brand name "Hao Feng Li" (very sharp) as well as another 3 words meaning "save effort" stamped. The back also have a sticker in a recessed area showing it's brand name, and the sticker is off center. The main body handle, snapper and slider are plastic.
[attach id=2 msg=2508843]
PartsThe snapper can slide out for changing blade, however the slit has warped and very hard to be used as a snapper (if not impossible). Better off pulling out a plier which I guess is always with a house renovation worker. Beside the warping, the plastic is too weak and thin to be used anyway, which probably will get the user hurt if used.
[attach id=3 msg=2508843]
Slider and snapper. Notice the slit gets narrower in the middle, hard to jam in the blade.The slider has a little spring in it. It only moves when pressed, when it returns to original height, a metal part of it locks to the teeth of the rail.
The blade is ok, but the lines for snapping off is too shallow. One must be very careful to snap it off clean with a plier.
Overall I think this is a dirt cheap cutter that does the job and not be afraid of being stolen or lost. The slider lock design is surprisingly well done. The only thing that makes it bad is cheap plastic, the wrapping of snapper, and even if the snapper plastic is good, it would be hard to be used anyway.
I have 2 Olfa's on my way. One of them with the Tajima will replace these two hopefully.




-
Day 16: Bought a new mat from Sam's Club for the kitchen. I'm thinking about buying one of these for each entryway, as well as high-traffic areas. They're easy to clean, and the backing is made from recycled tires, so it's pretty grippy.
I first used the Carpenter's Knife to start cutting away the plastic seal, but had trouble.
[attach id=1 msg=2508844]
Grabbed an older Kobalt I keep in a coat as the handle has a cutout that allows the blade to form a strap cutter. Thus, I was able to slit away the plastic without worrying about cutting the rug.
[attach id=0 msg=2508844]
Also opened up the chicken tenders with the Stanley.
[attach id=2 msg=2508844]



-
<u>Day 17</u>
Needed some assistance ripping the plastic sheeting off these cinnamon sandies.

-
Day 18
My no name snap off cheapo.

-
-
-
Day 19
SDI 0443C "InGenuity"
[attach id=0 msg=2508952]
FrontThis SDI cutter has some odd plastic over-shell and caught my eye when it is released. Took the chance to get one of these in this challenge.
[attach id=1 msg=2508952]
BackIt is advertised to have received 3 design awards. The outside is very different from what you see from usual A-size cutter.
[attach id=2 msg=2508952]
Bottom[attach id=3 msg=2508952]
TopThe plastic shell is ergonomic for different holding position. The slider is on the top of the cutter and hence it is left-right hand friendly without flip mounting. Near to the tip there is a cut-out notch in the plastic shell and the metal rail, which they design for cutting small strings safely without drawing the blade.




-
Continue
[attach id=2 msg=2508954]
Notch near to the tip for cutting small stringsBut from the deep down you can see it is not very different from a usual stainless steel A-size model if the plastic "over-shell" is taken away. The slider is enlarged to make it accessible from the top. And the snapper/end cap is modified to fit the plastic shell. It comes with a 30 degree blade for precision work.
[attach id=0 msg=2508954]
Parts[attach id=2 msg=2508954]
How the top is assembled. Notice the long slit for slider to move at the top of the shell, it can actually be the weakest point of this design.


-
Continue
It is auto-lock and claims the lock can hold up to 5kg. SDI aims this model towards hobbits and crafters, and most of the effort is put into making this cutter comfortable to hold in various position.
[attach id=0 msg=2508955]
"Pen" - for precision cuts. The 30 degree tip of the blade gives a clear view of the thing being cut even if only "1 or 2 snap" of blade is exposed (2 snaps in the photo above). One may want to keep it to 1 snap length sometimes since the longer it is, the more wiggle it can have. The slightly triangular cross section of the body is very similar to some of the kid's pencils and is very comfortable and stable to hold it this way.[attach id=1 msg=2508955]
Index finger against the top - the thickness at the top help giving extra pressure to the cut.[attach id=2 msg=2508955]
Hand grip in palm - the rounder body (compared to usual cutters) is easier to hold this way. This is for doing things such as sharpening an end of a wooden rod or a pencil.In summary, SDI puts out something new to the utility cutter landscape. This cutter is easy to hold in multiple positions and I think they succeed in archiving their design goal. The only thing I can pick at it is, the tip play is not as small as I wish (compared to top NT cutter A-500/A-1000 or OLFA LTD-04).
Lastly an action shot, slicing up an envelop (nothing crafty, unfortunately)
[attach id=3 msg=2508955]



-
Day 18
Despite my reservations, the Prybrid X has performed admirably thus far. Today, it broke down about a dozen boxes. Blade is a bit gunky, but still usable.

-
@LoopCutter: I like the variety of blades available for that Stanley!
@kaevin @ReamerPunch: my snap-off utility knife is likely even cheaper. I've discovered it flexes when in use.
@cody6268: the cord cutter notch seems very useful. I should get a utility knife so equipped.
@AzteCypher: those look fantastic!
@JonesE: Fastback and Bond seems like a great combo!
@BPRoberts: I should soon be breaking down a box, for the first time in months.
Day 18
Today's test subject was a padded envelope. (Contents will be seen on a day that doesn't bring upsetting news.)
[attach id=0 msg=2508959]
The Stanley cut straighter, but the DeWalt cut cleaner. We have a tie.
[attach id=1 msg=2508959]
Utility knife record: 13-0.
Stanley record: 2-3-1.
DeWalt record: 3-2-1..jpg)
.jpg)
-
@Jones: Nice pair ups in d17 d18!
@FarmerX: the HFL has a large stainless rail, so it won't flex. If it flexes, the workers wouldn't get them, that's the minimal requirement for them. Your blade comparison is interesting. I have a brunch of A-size light duty snap off blades but seldom compare them. -
Day 17. No real use--other than the fact I took inventory again. My EAB was in the nightstand for ages, but it somehow disaappeared.
[attach id=0 msg=2508963]

-
I think my favorite is RP's design. Of the color options, I think I like the light purple (top row, second from the left) the best.
-
Day 18
Open Christmas card duty tonight.
[attach id=0 msg=2508984]

-
<u>Day 18</u>
EAB got some use today.
First, I had to free up some leaf bags from their bindings.

Then, I did.... this.

So..... for those that are wondering, yes, you can cut an onion with a utility blade. It will do so quite cleanly. However, you'll have a hard time cutting some nice looking onion rings. Just thought I'd point that out.
-
Day 19
My Olfa tap knife. This rocks. Nice and flat, and it cuts extremely well. And they're inexpensive. Thank you, Olfa.

-
Day 18
The black, no name folding utility knife had such a tight pocket clip it could not be carried using the pocket clip. I used my SOG PowerDuo (which has been my desk multitool for about 10 years now) to bend it slightly so it will now go over the edge of the pocket as intended.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

