The December 2024 Utility Knife Challenge
-
Day 21
This was one part of a two pack of Milwaukee Fastbacks we bought earlier this year. We call it a "his and hers" set. This one is the "hers" and mostly sits on my wife's desk.
[attach id=0 msg=2509355]
I used it to make an ice melt scoop out (I warmed up the cider to drink after I cleared the snow).
[attach id=1 msg=2509355]

-
Day 21
Another month, another 40-pound box of cat litter.

-
Day 21
A package expected on Monday arrived today, surprise!!!
[attach id=0 msg=2509396]
The flip side, an Amazon package expected today, Now will not arrive until Tuesday, maybe. Strike!

-
Day 22
PL-1 has a mission to fix my racing shoes.
The outsole is coming off and some of it has deformed. Some already lost as well in last race
[attach id=0 msg=2509414]Cutting away the deformed part as it cannot be stick and will just peel off the whole thing, PL-1 in the back
[attach id=1 msg=2509414][attach id=2 msg=2509414]
Fix with clamps and tape[attach id=3 msg=2509414]
Hope it holds for 1 marathon



-
Oops double posted
-
@Alan K. said:
Day 19
No use today. The pocket clip was not easy to bend because of the odd shape. It is shaped like a hockey stick to accommodate the string cutting notch and this odd shape made it want to twist rather than bend under the force of the pliers. If I had to do it again, I think it might be better to remove the pocket clip first, then use the counter force of two pliers against each other. I could bend it however and wherever I wanted it bent, then reattach the adjusted pocket clip to the knife.
I think I have a silver version I bought at Dollar General a few years ago. Seem to recall the same problems with the pocket clip.
-
Day 19:
Basically nothing.
[attach id=0 msg=2509419]

-
Day 20:
For dinner tonight, I threw a Sam's Club BBQ sandwich in the microwave.
As long as you follow the directions to the tee, they're edible.
[attach id=0 msg=2509420]
However, I prefer to add cheese, an acceptable amount of BBQ sauce, and pickles.
I had to open up new packs of each.
[attach id=1 msg=2509420]
And remove the seal from a new gallon of milk.
[attach id=2 msg=2509420]



-
Day 22
Knipex Cutix assisting with my cardboard curtain.

-
Putting up another day 22 shot
Last pic only shown a blurred back of it.


-
Day 22
My wife wanted a pack of scissors from Sam's Club, and it came with this utility knife. It's a big sucker, and has a seemingly excessive four different buttons on it.


-
When you figure out what the 4 buttons do, please let us know.

-
Day 22
Another month, another bottle of pills.

-
Day 21 (catching up)
Cold weather and illness meant I had nearly no energy yesterday. This is about all I would have been good for.
[attach id=0 msg=2509512]
Day 22
Of course, this medicine had an obnoxious seal.
The no-namer in the kitchen took care of it, and awlso opened a bag of frozen burritos (I'm picturing AzteCypher shuddering at that).[attach id=1 msg=2509512]
Utility knife record: 17-0.
Stanley record: 3-3-2.
DeWalt record: 3-3-2.

-
Day 21
Did a little clean up in the garage on Saturday. Mainly cutting up some boxes from the big river and some other retailers. Wife likes to open up the boxes and dump the cardboard in the garage. So I got it all taken care of relatively quickly. Once done we got cleaned up and headed out to a pre Christmas get together with a couple of families.
JonesE
-
Day 22
Did a quick little side project this morning while the family slept. Yesterday a friend asked if I could take a look at a knife he had. I said sure and he handed me this CRKT knife he had in his toolbox in the garage while we very visiting. It was missing some screws and a spacer between the liners. So, I disassembled the knife and proceeded to give it a good cleaning with an old discarded toothbrush and some 70% isopropyl alcohol. All the parts looked ok, except for the cosmetic wear. I searched through my knife parts bin and found two spacers and four screws I then reassembled the knife with some blue loctite and adjusted the pivot. Checked the blade opening and closing and was happy the the blade was centered and the lock up was solid with a1/3 travel on the lock bar for full lock up. Then dropped of the knife to its owner this afternoon while I was out on chores.
JonesE
-
Day 22
End of the day, and realized I neglected a share thus day.
Was reading a travel magazine and dreaming of a Scotland visit.
So the background is
[attach id=0 msg=2509539]
-
Day 23
My Trojan folding utility knife. No crazy features. Just one-handed, folding, and locking. Cheap. It works. Also thin. Kinda heavy, though.

-
Nice work with that CRKT, JonesE!

-
Day 23
Olfa 185B extra long 3xtra thin wallpaper cutter
[attach id=0 msg=2509554]
In pqckageCutter #2 from Christmas package. I had been eyeing on this for a few years as well.
[attach id=1 msg=2509554]
Front[attach id=2 msg=2509554]
BackThis Olfa features an extra long blade (20 snaps) with 3xtra thin 0.2mm blades. Normal A sized are 3.8mm. Olfa has extra thin at 0.25mm and 0.2mm and nt cutter has 0.25mm for sa-400grp. This cutter can only fit 0.2mm it claims (I have not get a 0.25 to try)
[attach id=3 msg=2509554]
Blade vs normal blade



Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

