SAK-A-Like / Off Brand Challenge - September
-
Day 2
Ruike opened a popsicle
-
Day 3
The older the knife the stronger the springs, not as hard as my old SAK mod 1908 soldiers but a lot stronger than a modern SAK.
Got a real soft spot for these old Camillus US Army knives, there’s nothing wasted on them, just a good solid tool. This one’s from 1971

-
I did not had sadly something to do this Half Day for the Swizza, sadly, there are also not that many usefull Tools on it for my Workday, : The Skizzors are sadly not usefull, they look awesome: Fullsize Skizzors on an SAK Like, but sadly the 2 Sheer Halfs are not bound together strong enough that it can actually cut something.. , but other than that its a nice SAK Alternative: You can even get the Blade and the Bottle Opener out whit Gloves , if they would bring out an Modell whit a Normal Skizzors, i might get me this also ..
-
<u>DAY 3</u> Getting ready to lead a hike with an Adler.
[attach id=0 msg=2542774]

-
Day 3
The old-style can opener on the Rough Rider is used by plunging the tip through the can lid until the knurled peg touches the rim. That leaves most of the blade out of the can. Then you jig it up and down with the peg riding on the rim. Simple, right? Hmmm? This thing is sharp. It can close on your hand unlike a lobster claw or Victorinox type. You can get hurt with the newer type openers too, but you have to work at it. With the hand holding an applesauce can shielded by an oven mitt, I decided to try the thing. It has a large cross section, so it is hard to put through the lid. Problem one. With the sharp end turned away from you, you start in with the cutting. It cuts from inside the can, right? For me, it rode up right along the rim and scraped the inside of the can. You could get metal shavings. Problem two. It also requires a lot of effort making you push harder and increase the likelihood of an accident. Problem three strikes and out. I cut a little way with the tool, then decided it wasn't worth the effort. Plus I don't like shavings in the apple puree. I pulled out the opener and wiped it off. Then I found another problem. The opener was damaged. Evidently the can is harder than the blade. The blade was significantly dulled and had little nicks in it from just one usage. Bonus problem number four. I only cut an inch or so before giving up. I will say the tool is likely a good package opener. The nub on the blade prevents it from being much use elsewhere. I see comments on the net about Rough Rider (and the later Rough Ryder stamped knives) being rough finished, dull, gaps in the back springs, ill fitted emblems, etc. Others say they are well put together. I have to fall into the latter class. I have never seen a bad one. All the ones I owned (and handled) have been finished and fitted well with attractive handles and sharp blades out of the box. Same thing with the new imported Marbles, which look like they came from the same factory maybe? The springs on mine are very stiff. The awl is deadly sharp. The bone handles look great. The lanyard loop is annoying. I may remove that. It is a lot heavier than something like an old KampKing or one of the Imperial Irish red handled Sak-a-likes. I had one of those. There are some models with different can openers and I think one with carbon steel.Best wishes. G
:) [attach id=0 msg=2542777]
-
Day 1 (Even though its the 9-03)
Im currently surprised how good these Sheers on the Swizza S09 did work on Plastic Packing Band from a Pack of Cardboard Kartons whe use to pack Honey Jars,
so its only arch enemy is rope for now ..
Im again quite pleased whit this Knife, i was at first a bit dissapointed but in Combination whit the Swisstool Spirit, and the Minichamp its a quite nice SAK Alternative..Pictures will get add later, as i cant do this on my Work PC
-
Day 3 of 30
Today decided to take Armbar, opened few letters with blade and used scissors to trim my fingernails but gotta admit armbar scissors aint good for it.
[attach id=0 msg=2542785]

-
Gary, I've had good luck with the "Reserve" Rough Ryders, but only so so with the "regular" ones. While they're kissing cousins, I think the Marbles are a bit nicer than most Rough Ryders.
-
Day 3
The blue half Scout (Camillus) strike out will be carried again today, because I like it.
Was it a prototype? Or, a custom employee built with extra parts?
Oh well I like it.And, I included with it my first SAK-a-like classic. An employer recognition award from 1975, my 2nd year, for some special accomplishment. My name is engraved on the other side. I pocket toted this for many a year and opened envelopes, boxes, and other packages as well as freeing toys from packages for kiddos that arrived after ‘75, as that was year the promise I publicly made to my new bride, wow 50 years ago!
[attach id=0 msg=2542788]

-
I think everything I had was a Rough Rider with an I in Rider. I did have Marbles. That was a good paracord job on the Buck. It improved the looks of that thing a lot. Probably the feel in hand also. Best wishes. G

-
I used to see Camillus and Kabar knives with the tang stamps defaced or removed. Most were just ground off with a grinder. All of the emblems were pried off the handles (if they had any). My cousin had a bunch. I am reluctant to tell anyone just how many he had, because nobody would believe me. They are all rejects. Sometimes it is easy to tell why they were rejected, and sometimes it is hard to say. I couldn't see anything wrong with lots of them, other than being filthy.
The Camillus you have looks a lot like a Cub knife. The World Scouts have their knives that same purple color. It could have been a World Scouts knife that never got the blade stamp or emblem. Just a guess.
Best wishes. G
:( -
Pretty much describes this example
[attach id=0 msg=2542793]
[attach id=1 msg=2542793]
[attach id=2 msg=2542793]


-
I haven't run into one struck out like that before. Very interesting.
-
The pictures for Day1 (un)
Et voila: First : my todays EDC (Swizza S09, Vic Swisstool Spirit X, Vic Minichamp
Second what I did whit the Swizza:
Oh and i did also use this Rimer things to open a Pack of Dymo Label Writer Labels..

-
Day 3
used the scissors on the Armbar Slim Cut to open a snack at work.

-
Day 3: A good blade and fantastic lockup! Great turnout everyone!

-
Day 4???
You move to OZ of New Zealand? -
@nate j said:
Day 2The Gerber Armbar Slim Drive (henceforth GASD) on cigar duty.
Thus far:
I give the concept an “A”. The idea of a fairly slim, light, and compact tool that contains a blade and some decent screwdrivers (in this case, a bit driver with a single bit that is flat on one end and Phillips on the other), plus the obligatory bottle opener of course, is a good one.
I give the execution a “C”. F&F isn’t terrible, but not on par with Vic standards.
The blade is supposed to be OHO (my example is quite stiff, but may loosen up with use) and features a liner lock. I also don’t like coated blades and don’t feel the wharncliffe blade shape is the best option for general EDC, but these last two are really personal preference.
The bit driver strongly retains the bit thanks to what appears to be a rare earth magnet; good job by Gerber on this, as nothing ruins the experience of a tool with removable bits faster than bits that fall out/get lost. The bit driver is also pretty well centered in the tool, which makes it much more pleasant to use than MTs with offset drivers. A second bit with some different tips might have been nice, but I’m betting the included double-ended bit will handle the majority of screws most folks will encounter.
One oversight, IMO, is that the bit driver does not lock open. I would much rather have a blade that doesn’t lock and a screwdriver that does (e.g. TL-29) than a blade that locks and a screwdriver that doesn’t (as the GASD has).
I haven’t tried the bottle opener, but as this is possibly the easiest tool to build of any commonly found on MTs, I’m willing to assume it opens bottles. I don’t like the tool opening mechanism though; apparently, the only way to open it is by applying pressure to the ridges on the back of the tool. There is no nail nick or other more positive means of opening that I can see. Like the blade, the bottle opener on my example is quite stiff, but may loosen with use.
Overall, I think most users (including yours truly) would be better served by spending the extra $10 for a Vic Explorer.
Nice write-up on your assessment so far. I'm using a Gerber Armbar Slim Cut (GASC) for the challenge, so I might as well volley some thoughts back at you.
I've had varying luck with using the one hand opening on the blade, but I must admit I like having the option. I like it much better than the OHO method on the Vic Trekker because theres no worry that if I lose my grip, the blade snaps back on me. It's not smooth by any means, but if you think of it like a friction folder (which it basically is) then you can get on with the idea a little easier. I'll admit it ends up being a two handed operation sometimes - especially when disengaging the lock. But so far i'm enjoying the capability.
As for the blade shape, I do like this sheepsfoot quite a bit theres definitely an advantage of having the tip angled downward instead of forward for some tasks.
Now then - before this challenge started, I was searching online for another contender for a SAK similar - and I noticed that other brands that have locking tools do not put a lock on the bit driver. That lead me to think - could it be that the tang of the bit driver does not lend itself to a locking mechanism as easy as the tang of other more 2-D tools? Maybe. At least thats the thought I had once I noticed the same issue with other tools.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

