Show your slip joint's thread!
-
Spork,
They did a run of Case Scouts in Yellow Delrin but I can't recall if they were CV or not, been a while since I have seen one.
Princess Pollywog & Mike,
Oh yes, Case still makes runs in their CV Carbon Steel. They recently released some new runs of CV slippies in Red Bone and Chestnut Bone, and they still make many patterns in their Yellow Delrin with CV blades.
Looky here: http://www.wrcase.com/knives/pocket_knives/browsefolding.php?Family='Chestnut Bone CV'&Folding='1'&Item='' and here: http://www.wrcase.com/knives/pocket_knives/browsefolding.php?Family='Dark Red Bone CV'&Folding='1'&Item='' and also here: http://www.wrcase.com/knives/pocket_knives/browsefolding2.php?Family='Yellow Handle'&Folding='1'&Item='0111'
Their "Tru-Sharp" Stainless is 420HC, they do use it alot. But aside from that and the CV they have used ATS-34, 154CM, Rain Drop Damascus, and BG-42 in their knives. Just depends on the run.
2xTap
-
Yeah sure... for a premium ^3 price! :ahhh
-
-
Princess Pollywog,
Just depends on the run. The Tested XX in 154CM had most of the patterns available for under $100 and the Burnt Amber Jigged Bone series in Damascus could be found with most of the patterns around the $100 mark........not bad considering they are 100% American Made.
Spork,
It happens to me all the time. Sometimes I have to hunt through my collection before I buy something cause I can't remember if I have it already.
2xTap
-
I really have not been interested in a slip joint, form just didn't do it for me. Now I see Case makes a OHO locking knife, I love that it looks old school but with a modern function.
-
@2xTap said:
Princess Pollywog,Just depends on the run. The Tested XX in 154CM had most of the patterns available for under $100 and the Burnt Amber Jigged Bone series in Damascus could be found with most of the patterns around the $100 mark........not bad considering they are 100% American Made.
If you don't think that's expensive something's wrong with your head.
Really. How much do you think it costs them to make a knife?
I don't blame them though, frankly they can get away with selling the Surgical Stainless to 99% of their customers so they might as well. But even those are way overpriced. -
I can't be right in the head either as that sounds reasonable to me.
-
Princess Pollywog,
In the $100 range is quite reasonable actually for an American made slipjoint using 154CM or Damascus steel. Try to get the same thing from a custom maker and then it gets expensive. Crazy! If you only knew.........I've got tens of thousands of dollars wrapped up in my knife collections. $100 to $150 for a well made American pocketknife that will last a lifetime or two is nothing.
As to Case's Tru-Sharp stainless.....yeah, some of the patterns are expensive like the Gunboat Canoes. But it is alot of knife with alot of steel. And these aren't just some stamped out knives......alot of hand operations go into these.
And their Tru-Sharp stainless is actually 420HC Stainless.......the same steel used in many Buck Knives, the same stainless used in many Schatt & Morgan's and Robeson's from Queen, and the same steel used by Great Eastern Cutlery in the new Cripple Creek SFO's. With the right heat treat it's a good steel......I know, I have been using it for years without a problem.
2xTap
-
Here's a pretty one.


-
@2xTap said:
Princess Pollywog,In the $100 range is quite reasonable actually for an American made slipjoint using 154CM or Damascus steel.
No, it's not. :D
Until you give me proof to show me otherwise, I'm prone to believe the material costs are actually pretty dang low per knife.@2xTap said:
As to Case's Tru-Sharp stainless.....yeah, some of the patterns are expensive like the Gunboat Canoes. But it is alot of knife with alot of steel. And these aren't just some stamped out knives......alot of hand operations go into these.Not $80's worth. Not even $60, $40, or $20. Okay, maybe $20's worth.
@2xTap said:
And their Tru-Sharp stainless is actually 420HC Stainless.......the same steel used in many Buck Knives, the same stainless used in many Schatt & Morgan's and Robeson's from Queen, and the same steel used by Great Eastern Cutlery in the new Cripple Creek SFO's. With the right heat treat it's a good steel......I know, I have been using it for years without a problem.2xTap
I'm fine with any kind of blade steel on a pocket knife as long it's not aluminum :D ... as long as the heat treat is good. But you can get pocket knives in so called "premium" steel elsewhere for much cheaper. Or crappy 400 series stainless ones from China with decent fit and finish for half a ten.
-
@ducktapehero said:
Here's a pretty one.

I love rehandled SAKs. I saw one with Stag and bolsters that was to die for.
-
Princess Pollywog,
Material costs might be low, but that is just part of the cost.....then you got the cost of manufacture which is not cheap here in the USA, and then you pay for the brand. In the matter of Case we are talking about the most collected brand of knives. And knives that generally don't lose value.
Value of any knife or brand is a subjective thing........but as to their proof of value on the market all you have to do is look at the market. Regular production case pieces can be had at reasonable prices. But when you get into their SFO's and limited run items the collector market forces the prices through demand. Add in age and you can often see the prices slowly climb.
The question is..........can you show me a knife of equal or better quality that will have a similar collector value for whatever inexpensive price you see better than that of a Case?
Good luck! :D
2xTap
-
Case is owned by zippo isn't it? So if zippo can sell stamped sheet metal for $30, why can't case sell their 420HC knife for $100? :P
-
Case is owned by Zippo.
2xTap
-
@2xTap said:
The question is..........can you show me a knife of equal or better quality that will have a similar collector value for whatever inexpensive price you see better than that of a Case?Alas, was I looking for a collector piece? Do I care about resell value? I'm just saying, there are many knifes that can be had for cheaper of equal or better quality. I'm saying the cost is NOT reasonable for the labor and parts put into it. It's not. That's why I don't buy Case.
If I was a collector, of course it'd be different.
Disregarding "collector value" and only considering manufacturing costs and labor... I cannot in my right mind say any Case knife is worth its value.
'Cept maybe a soddie.@jzmtl said:
Case is owned by zippo isn't it? So if zippo can sell stamped sheet metal for $30, why can't case sell their 420HC knife for $100? :PI get along fine with BIC lighters and fake cheapos. :P
-
Sorry to jump in on this discussion, but I'm curious to see what you regard as being of equal quality but much cheaper. Got any links?
-
points at SAKs :D
Sorry, I'm on satellite now, a bit hard to go knife browsing, will post some links when I get home. If I remember.
-
@Princess Pollywog said:
points at SAKs :DThis is not meant as a bash to Vic or Wenger as I am a fan of both, and they do build a good quality tool but you are comparing Apples to Oranges. There is a reason why most Vic's and Wengers cost so little. The average 91mm Vic is made of their standard stainless which is usable but softer than the 420HC that Case uses on most of their runs. Vic also uses a much thinner blade stock on many of their blades than Case uses on most of their slips (this does vary by pattern), most SAK's are scaled in essentially plastic that is stamped out like cord wood where most Case slippies are done in Jigged and Dyed cattle bone, most of your SAK's are lined in thin Aluminum stampings where most Case knives are lined in polished brass (or Nickle/Silver, depends on run), all production SAK's come un-bolstered where most all production Case slippies come bolstered in polished Nickle/Silver.
But all of this varies extremely with Case as they do so many different runs that add much more expensive handle materials, blade steels, finishes, different inlay shields, etc. And Case specializes in Traditional pocketknives, not multitools.
Outside of that there is also the History and Tradition, of which I won't get into in this thread.
But if we break this down and try to compare on equal footing we would have to take something like one of Case's Workman Series Scout Knives which has some tools in it...................
............and go with a Vic Soldier, which has the same tools/blade set-up. And then there ain't much of a price difference. I picked up my Case Workman Series Scout for only $26.00 NIB.
2xTap
-


I won this thing on auction about 2 weeks back for a song.....really dirt cheap. Thing is, the knife I recieved was not the knife that was listed. Both are similar but the one listed was a different pattern. I emailed the dealer I got it from and have yet to receive a reply......I ain't sweating it for I would of got this one too had it been listed as well. And as this knife was had so cheap, and it's just as nice, I'm happy either way. Odd how that worked out!
Anyway, the knife that was listed was a 2003 Robeson Shuredge Large Barlow "Demonstrator" in Red Smooth Bone. The knife I got was this one, a 2002 Robeson Shuredge Coke Bottle "Demonstrator" in Red Smooth Bone. Similar run just different pattern and older.......and like I said, I ain't sweating it! :D

These were a limited run of "1 of 100" and have the "Demonstrator" tang stamp. From what I have gathered these were reproductions of older Sales Sample knives.
And it's a big'un! My own measurement has this puppy at 5 3/16" from bolster to bolster. And it is hefty too with some thick blade stock, large slabs of bone, and long bolsters. Blade is a long Clip, fully swedged with long matchstriker pull and made from 420HC Stainless. Bolsters and shield are nickle/silver, and liners and pins are brass. Scales are smooth bone dyed in a beautiful shade of Red.

Fit and finish is excellent, but with two small faults which I will get into in a bit. Blade has half-stop, but opens and closes smoothly without any play. Backspring is stout, and it rests flush with the blade opened or closed. Scales fit to the bolsters and liners seamlessly, and the pins are flush to the scales. One fault here is in the backspring area. Liner and backspring fit is seamless up until you get to the pivot end on the non-shield side bolster.....here there is a small tiny gap, barely a hairline between the backspring and liner. It's tiny as hell but something I noticed.

The other fault is the edge. This is the first Queen-built knife I own that came dull out of the box. The edge is ground clean and even, but the bevels look to be at about a 40-45 degree angle, very steep making the edge quite blunt. Easily rectified if this was to be a user, as it is going into the collection it's no big deal.
Outside of that this thing is flawless, and mirror polsihed throughout. It's a looker! It came mint with it's original box but had no paperwork. The box itself is very clean and mint as well......either way it was a steal for only $56.99!!!!

2xTap
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
???
