December 2025 Tool Box Challenge
-
@fullbreakfast said:
Day 19Mini challenge, alternative use of a tool that it was not intended for.
Here is something everyone knows about, but I had never actually tried.
In my EDC pouch I have a couple of needles and some thread:

I magnetized the larger needle and suspended it from a bit of thread to see if I could get it to function as a makeshift compass.
It worked!

The only tricky part was adjusting the position of the knot to get the needle balanced horizontally. Also, I did not appreciate until I tried this, how careful you need to be to have your needle well away from other ferrous material that will interact with a magnetic field. I initially tried suspending the needle using a rod placed across the open doors of a steel cupboard. It did not work properly.
Now I just have to remember that it is the eye end of my needle, not the point, that indicates north.
Side note, I considered using my mini ferro rod for this instead of a needle, but the Internet tells me that ferrocerium is not in fact sufficiently ferrous to be magnetised. Too much other stuff in the alloy.
This was my serious entry. I also have a silly one that I will post later.
Good work!

Assuming your needle is small and light enough to float, I have heard (not tried) that floating it in a cup of water or expedient puddle can be an easy way to avoid the challenge of getting the knot at the needle’s center of gravity. Just have to take care that the needle is truly free to rotate, i.e. not touching the sides (or bottom) of the vessel.
Also, as you say, the importance of keeping metal away can’t be overstated. I was out once on a Scout campout when one of the other leaders started playing with a small compass. He noted it appeared to be junk/broken, as it wasn’t reading accurately. I asked to see it, and promptly removed the little metal clip (presumably added to allow it to be attached to a zipper pull or the like), whereupon it immediately began reading correctly.
-
Day 19
Mini Challenge
First pic: Farmer X and I have been discussing Maglites, so here is a basic 2D version doubling as a nutcracker. It just occurred to me that Nutcracker is also relevant to Christmas.
Second pic: I posted the concept before of using the Visegrips as a bit driver. Here's an actual demonstration.
I also ended up using it as a nail puller. The piece I'm working on is part of a cabinet I scrapped. I've been removing the hardware for reuse, and my intention is to burn the wood in my woodstove. After getting the screws out, I was pulling nails with my mini prybar which turned out to not be up to the task. So instead of permanently damaging the prybar, I used the mini Visegrips which proved to be more than strong enough.

-
<u>Day 19</u>
Here's my entry. Using a knife as a mini pry bar. I was in charge of getting this garland lit up and I was wearing out my thumbs and nails trying to pull out the little bulbs. I used this little folder as a mini pry bar to pop them out. Worked pretty darn good on the about 100 lights I had to swap out.

The wife keeps telling me we can just buy a new light up garland but I hate throwing things out that just need a small repair. The problem I ran into this year, is that I couldn't find any suitable donor lights at the store. I found the regular incandescent string lights but the bulbs seemed to be rated for less amperage or voltage. The minute I'd put them into the bulb base, it would immediately pop again. I dug around in our Christmas light bin and found an old strand with white bulbs and those worked fine. I might have to give in and buy a new led strand just because I can't get parts anymore.

-
Day 19 mini challenge
A paper clip was involved in satisfying the particulars described.
I have lost some dexterity with my fingers, with buttons on my shirts providing a challenge. So a couple years ago I acquired a few button tools and they are positioned throughout the house were I would require this tool.
Then a friend of granddaughter injured herself and could not do buttons on handed. So, being in the MacGyver challenge at that time, I fashioned a paperclip with duct tape to assist her. And loved it. Best one arm hug ever.
I later fashioned one for myself and it is in my travel valet.
A paper clip maybe the most versatile tool that can be adapted
[attach id=0 msg=2556604]
The original next to the paper clip model.
[attach id=1 msg=2556604]
The original unbuttoning, slip over and guide through the button hole.
[attach id=2 msg=2556604]
And,the paper clip model, slip through the hole, slips over the button and guide through the button hole , then remove.In my years, a paper clip saved me many times.
Replaced a light duty fuse in low voltage circuit, as a pice of wire soldered to a board to link voltage across a weak circuit trace. To mend a hem that the thread came loose on daughter’s dress. Fashion as a hidden hair pin, slid into a zipper pull to return a zipper to functionality.Even a temporary keyring to group some keys together.



-
Mini Challenge
First pic: Farmer X and I have been discussing Maglites, so here is a basic 2D version doubling as a nutcracker. It just occurred to me that Nutcracker is also relevant to Christmas.
Second pic: I posted the concept before of using the Visegrips as a bit driver. Here's an actual demonstration.
I also ended up using it as a nail puller. The piece I'm working on is part of a cabinet I scrapped. I've been removing the hardware for reuse, and my intention is to burn the wood in my woodstove. After getting the screws out, I was pulling nails with my mini prybar which turned out to not be up to the task. So instead of permanently damaging the prybar, I used the mini Visegrips which proved to be more than strong enough.Excellent uses! It seems like there is no end to what you can do with a Maglite. I still have a very old one somewhere, and it still works.
-
@LoopCutter said:
Day 19 mini challengeA paper clip was involved in satisfying the particulars described.
I have lost some dexterity with my fingers, with buttons on my shirts providing a challenge. So a couple years ago I acquired a few button tools and they are positioned throughout the house were I would require this tool.
Then a friend of granddaughter injured herself and could not do buttons on handed. So, being in the MacGyver challenge at that time, I fashioned a paperclip with duct tape to assist her. And loved it. Best one arm hug ever.
I later fashioned one for myself and it is in my travel valet.
A paper clip maybe the most versatile tool that can be adapted
[attach id=0 msg=2556604]
The original next to the paper clip model.
[attach id=1 msg=2556604]
The original unbuttoning, slip over and guide through the button hole.
[attach id=2 msg=2556604]
And,the paper clip model, slip through the hole, slips over the button and guide through the button hole , then remove.In my years, a paper clip saved me many times.
Replaced a light duty fuse in low voltage circuit, as a pice of wire soldered to a board to link voltage across a weak circuit trace. To mend a hem that the thread came loose on daughter’s dress. Fashion as a hidden hair pin, slid into a zipper pull to return a zipper to functionality.Even a temporary keyring to group some keys together.
Ingenious. This is great stuff!
I do agree about the usefulness of paperclips. I like to carry a few in all my bags.
Probably my most frequent use of them is for applying epoxy and other viscous glues, when I need to be precise and get the stuff into small gaps (I mend a lot of broken toys). My little bag of glues always has a few bent paperclips in it.
-
@AzteCypher said:
<u>Day 19</u>Here's my entry. Using a knife as a mini pry bar. I was in charge of getting this garland lit up and I was wearing out my thumbs and nails trying to pull out the little bulbs. I used this little folder as a mini pry bar to pop them out. Worked pretty darn good on the about 100 lights I had to swap out.

The wife keeps telling me we can just buy a new light up garland but I hate throwing things out that just need a small repair. The problem I ran into this year, is that I couldn't find any suitable donor lights at the store. I found the regular incandescent string lights but the bulbs seemed to be rated for less amperage or voltage. The minute I'd put them into the bulb base, it would immediately pop again. I dug around in our Christmas light bin and found an old strand with white bulbs and those worked fine. I might have to give in and buy a new led strand just because I can't get parts anymore.

Excellent use. Your "fix it, don't throw it out" approach is something that strikes a chord. Particularly in this season of over-consumption.
-
@nate j said:
Good work!


@nate j said:
Assuming your needle is small and light enough to float, I have heard (not tried) that floating it in a cup of water or expedient puddle can be an easy way to avoid the challenge of getting the knot at the needle’s center of gravity. Just have to take care that the needle is truly free to rotate, i.e. not touching the sides (or bottom) of the vessel.I thought about this, but with my big old needle I would have had to mount it on a bit of cork or other buoyant material, and I couldn't be bothered. Also, the approach I took meant I was self-sufficient, only using things I had in my EDC pouch. The drawback is finding a suitable place to hang the thread...
-
Day 19
Mini Challenge
I was curious how the P-51 would work as a package opener.
Getting through the tape on the box was slower and sloppier than I had anticipated (probably made worse because this sort of tape has strings embedded in it to improve its tensile strength). But the P-51 did ultimately get the job done.
But how would the P-51 fare against the dreaded clamshell/blister pack?
I first tried to make a cut through the whole package, like I would with a knife. But this was very difficult going and I eventually abandoned it as not workable.
However, my second approach was much better. I was able to use the P-51 to score the plastic immediately around the Jetsetter. It took an average of probably two passes to cut through the plastic, and once I had cut sufficiently far around, the Jetsetter was easy to remove from the package.
In conclusion, the P-51 will function as a package opener if it is the most suitable tool you have. But it is certainly not convenient or preferred for that job; a good sharp knife is far better.



-
@nate j said:
Day 19Mini Challenge
I was curious how the P-51 would work as a package opener.
Getting through the tape on the box was slower and sloppier than I had anticipated (probably made worse because this sort of tape has strings embedded in it to improve its tensile strength). But the P-51 did ultimately get the job done.
But how would the P-51 fare against the dreaded clamshell/blister pack?
I first tried to make a cut through the whole package, like I would with a knife. But this was very difficult going and I eventually abandoned it as not workable.
However, my second approach was much better. I was able to use the P-51 to score the plastic immediately around the Jetsetter. It took an average of probably two passes to cut through the plastic, and once I had cut sufficiently far around, the Jetsetter was easy to remove from the package.
In conclusion, the P-51 will function as a package opener if it is the most suitable tool you have. But it is certainly not convenient or preferred for that job; a good sharp knife is far better.
Excellent write up, thanks. This is the kind of empirical research we love to see!
-
Day 19
Mini Challenge
The treasure map was ancient and tattered, stained with old blood and singed with the sparks from flintlocks. It promised great riches to those who could navigate a perilous route - one that finally led through the Caverns of Almost Certain Doom.
Only the most intrepid of pirates would brave the attempt. Captain McTweety, the boldest canary sailing the seven seas, was such a one:

At last he and his ragged crew had reached the narrow bridge that crossed the final ravine. The map marked this as the Spirit Level Bridge - so called because only those of dauntless spirit and level head could hope to make the crossing. The Captain led the way.

Buffeted by infernal gusts, some fell, and met an awful fate:

A few hardy souls made the crossing.

And the treasure was won at last. A hoard worth more than a king's ransom:

Now, how to get it back to the ship...
-
@AzteCypher said:
Used the Rough Ryder to open up some coffee in the morning and a little gift my mother-in-law got me for my birthday.
@nate j said:
I think we have reached the point with many household appliances where they may be worth repairing if and only if you can do the work yourself or know someone who will do the work for free.
I got lucky with the repair on my old washing machine (after having to wrangle a replacement drain pump twice). It worked perfectly until I left that house. The matching dryer went a dozen years with no repairs needed.@King_Gorilla said:
This is my truck hatchet.The nail puller on the other end could be handy. I can't quite make out the stamp on the head. Who made it?
@fullbreakfast said:
I magnetized the larger needle and suspended it from a bit of thread to see if I could get it to function as a makeshift compass.It worked!


@LoopCutter said:
A paper clip maybe the most versatile tool that can be adapted
Day 19
Alternative use of tool mini-challenge
This is a good exampe of what can happen when ol' Farmer X gets a little OCD. (I think everyone who enters military service and doesn't get shipped out on a failure to adapt discharge is subject to a certain degree of it). I took two old utility knife blades and, after some trial and error, got 'em taped together just right. The jury-rigged contraption was then used to set spacing between Mirco Machines.
[attach id=0 msg=2556636]
The car at right in the second photo is from the Radicators line, which was scaled larger than normal Micro Machines. The Super 4x4s are considerably wider than the normal cars. Therefore, getting them spaced properly (and keeping them clear of the hutch door track) also required some trial and error. The blades were removed from the Gerber EABs, so it seemed appropriate to include them in the photo.
[attach id=1 msg=2556636]
There will be at least two more Micro Machines appearances in the remainder of the challenge.
.jpg)
.jpg)
-
That is indeed a good looking hatchet, Farmer. Very useful. I think it says True Temper. I'm sure KG will correct me if I'm wrong.
ETA: I was right. It says "True Temper" and below that, "Tommy Axe." I found a 1954 True Temper catalog on Archive.org, and it's in there.
-
Day 18:
I think I bought this Crescent 4" adjustable at Tractor Supply 6-7 years ago. I had retired my Craftsman 4" from the early '10s (still USA/Western Forge) due to it being harder to find. I retired this one when I got my Duluth Handiboy, but decided to put it back in service as TSC and Auto Zone (as Duralast--Danaher/Apex is their OEM) still carry them off and on.
Originally, it had a red dipped grip, but it got chewed up (as I often used the hang hole as a T-Post clip tool) and I cut it off.
I only vaguely recall buying the even smaller 3" (no-name) at a local farm supply store when I was about 5. Think it was $2? It's surprisingly pretty decent with almost no slop. For most of its life, it lived in my Erector/Meccano box.
Also carried the Husky 4-in-1. Like the famous Craftsman, it was often included in sets (and Western Forge made), but sold by Home Depot. Bought 4 of these online for cheap a few months back to about double the 4-in-1 keychains I had.
Most of my Ferraris (and one Lambo from the '70s by Playart) as well...
[attach id=0 msg=2556648]

-
Day 20

-
Alternative use of tool mini-challenge
This is a good exampe of what can happen when ol' Farmer X gets a little OCD. (I think everyone who enters military service and doesn't get shipped out on a failure to adapt discharge is subject to a certain degree of it). I took two old utility knife blades and, after some trial and error, got 'em taped together just right. The jury-rigged contraption was then used to set spacing between Mirco Machines.
[attach id=0 msg=2556636]
The car at right in the second photo is from the Radicators line, which was scaled larger than normal Micro Machines. The Super 4x4s are considerably wider than the normal cars. Therefore, getting them spaced properly (and keeping them clear of the hutch door track) also required some trial and error. The blades were removed from the Gerber EABs, so it seemed appropriate to include them in the photo.
[attach id=1 msg=2556636]
There will be at least two more Micro Machines appearances in the remainder of the challenge.
Hah, I would never have thought of that. Good work!
-
Thanks to all who participated in the day 19 mini challenge! Hope you enjoyed it as much as I did. The entries were great.
The baton for December’s final mini challenge has been passed on. I expect we will hear from the new task setter what the Boxing Day challenge is to be in the next few days.
-
Day 20
Maybe some more scissors wouldn't be out of order here. Another set of barber scissors and a very small one for trimming annoying stray hairs. The ends are rounded so you won't poke a hole in your nose or something. Also, a photo of my lost cheapie flashlight. When I found it, I didn't see any evidence of it having been burped up by something. I wiped it down anyway. Congrats to friend fullbreakfast for his excellent mini-challenge hosting and proper handing off of duties to the next taskmaster. Perhaps he will decide to host his own challenge someday.Best wishes, Gary

[attach id=0 msg=2556664]
-
Day 20
Putting up more shelves.
In my quest to find a replacement for the 93mm Vic awl - my preference for making starter screw holes - I got hold of this 1/4” reamer bit made by Megapro.

It is a chore to use with a regular bit driver, but does the job nicely in an electric screwdriver.
Due to the dubious design of these shelf brackets, and my preference for using good long screws when attaching things to walls, I had to resort to my stubby bits in a Wiha mini ratchet here:

The Marxman is really handy for this kind of job:

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

