How hard is it take apart and reassemble a SAK?
-
You could get them to 0.48mm difference by swapping the pliers and the magnifier layers between tools...

-
@RedRamage said:
figure out a way to get them even closer.What if you move the file from its current location, placing it between the pliers and saw? That would let you drop a liner, as you can have the file/saw/scaler with no liners in between, and you'd be at 24.29mm for Red, only 0.3mm difference. At that point sand 0.1mm off each of Red's 3 internal liners and they'd be exactly the same thickness.
One other question - why Corkscrew on both, rather than Phillips on one of them? Is it to carry two different micro drivers?
-
@TazzieRob said:
You could get them to 0.48mm difference by swapping the pliers and the magnifier layers between tools...
I could, but I very specifically want the pliers on a different knife from the screw drivers. The idea is to be able to hold a nut with the pliers while turning a screw with the other knife. So I'm starting with the "rule" that all drivers are on one and the pliers on the other.
-
@Adreaver said:
What if you move the file from its current location, placing it between the pliers and saw? That would let you drop a liner, as you can have the file/saw/scaler with no liners in between, and you'd be at 24.29mm for Red, only 0.3mm difference. At that point sand 0.1mm off each of Red's 3 internal liners and they'd be exactly the same thickness.Interesting thought... I'll admit I'm not I don't know enough about the reason for liners to know if this is a good idea or not. I do know that Victorinox has knives with the wood saw and fish scaler without a liner in between, but I'm not sure if they have any with the metal, wood, and fish all together without a liner. I also know that they have a knives with the an arrangement of *Liner *- Metal - *Liner *- Wood - Fish - Liner. I would seem that Victorinox thinks there needs to be a liner in there. I'm just copying them.
One other question - why Corkscrew on both, rather than Phillips on one of them? Is it to carry two different micro drivers?
Exactly this reason. I did consider the Philips instead of the cork, but I already have the inline Philips which I think is a better big Philips driver. I know I could replace the inline Philips with a lite, but I've never been a big fan of those lights and when I need a light I've got my phone's light I can use... plus I might add a mini flashlight to my edc too.
-
Update: I'm part-way finished. I ran into some issues multiple times, but I've finally finished the first knife. I'm going to share a few things in my progress in case anyone else finds this thread later while they're considering making their own custom SAK.
First, taking a knife apart: Not having a drill press, I designed to use a dremel tool with a "ball bit." This worked well enough, but I had some issues. First, I wasn't very good at keeping the ball on the pin itself. I slipped more than a few times and gouged the aluminum liner... sometimes pretty bad. This wasn't catastrophic for me because I was was using a handful of different donor knives so had extra liners. Plus I'm using solid (ie, not translucent) scales so it'll hide my bigger sins. The bigger issue is that I also damaged a number of collars. I'd recommend NOT using the dremel like this unless you have decently steady hands. It works, but the risk of damage is pretty high.
Second, collars: Did you know there's a top and bottom to these? Okay, yeah... maybe this is obvious but never under estimate the stupidity of someone who knows just enough to get into trouble. Yeah, my first assembly attempt had these all on backwards. Oops. That was a waste. Just make sure you put them on the right way.
Third: man I suck with hammer: I've watch multiple videos on how to peen (pein?) pins and yet I just can't seem to do it well. I would highly recommend practicing one some old pins from your donor knives a lot. I think I ended up bending my pins multiple times. As I mentioned I did get one knife finished last night, but I know at least one of the 2.2mm pins is a little bent.
All in all it's not perfect, but it doesn't have to be. This isn't going to be a showcase knife... this will be an EDC so it's gonna get bumped up, banged around and it'll get some scars over time. So starting with a few imperfections isn't the end of the world. And I get to proudly say that I made it... well, assembled it at least. There's some satisfaction in being able to say that.
-
It's a great feeling to finally pop the scales back on to a finished mod, especially your first one!
You're right to be proud - you took a risk to make something unique to you and succeeded.With drilling out the pins, I'd recommend using a center punch to mark the centre of the pin and using a metal drill the same diameter as the pin to drill it out and it should provide a greater degree of accuracy.
Peening is just practice. And using the right tools. I used my Estwing claw hammer for my first effort and while it worked it wasn't nearly as good as the little ball peen I've been using subsequently. Also, patient and gentle tapping gets you there slowly but surely.
When can we see some pics?
-
Congratulations on the achievement. I agree it is something to be proud of and thanks for sharing your experience!
-
Well done RR -
And yes, for the first few times, there are going to be a few challenges along the way - it takes a little practice.
I am a bit of a DIYer myself and try to do most of the jobs around the house - The challenge on that, is that nearly everything you do, you are doing it for the first (and possibly only) time, compared to the tradey who only does that job, has done it a thousand times, and get it done in 1/10 the time it takes you!

So a bit like all these youtube vids of the experts building SAKs - They make it look so easy!! But it ain't
-
Sounds like you’re off to a great start!
@RedRamage said:
First, taking a knife apart: Not having a drill press, I designed to use a dremel tool with a "ball bit." This worked well enough, but I had some issues. First, I wasn't very good at keeping the ball on the pin itself. I slipped more than a few times and gouged the aluminum liner... sometimes pretty bad. This wasn't catastrophic for me because I was was using a handful of different donor knives so had extra liners. Plus I'm using solid (ie, not translucent) scales so it'll hide my bigger sins. The bigger issue is that I also damaged a number of collars. I'd recommend NOT using the dremel like this unless you have decently steady hands. It works, but the risk of damage is pretty high.I think the Dremel plunge router has the potential (along with a clamp or two) to function like a poor man’s drill press. Price is quite reasonable, especially if you already have the Dremel…
-
@magentus said:
Peening is just practice. And using the right tools. I used my Estwing claw hammer for my first effort and while it worked it wasn't nearly as good as the little ball peen I've been using subsequently. Also, patient and gentle tapping gets you there slowly but surely.Yeah, that's the part that causes me some issues! :D I'm not so good on the patience part. One of the problems I was running into was holding the pins while trying to do the initial peening. I have a small vice, but when I used it marred up the pins, so I wasn't happy with that, but obviously just holding them in my hand wasn't going to work either.
I finally hit upon a solution that mostly worked... I 3D printed two small blocks with a half circle cut out of of each that was a little too small for the pin. I think clamped those blocks around the pin and could really tighten up the vice on the blocks to put pressure on the pin with out digging into the brass.
This wasn't a perfect hold so the rod would slowly slip through the blocks as I peened, but I could get quite a number of taps in before I'd have to adjust the pin back up. This helped a lot with the process for me.
When can we see some pics?
Their coming. I'm gonna do a new thread with pics because I'm assembling a new EDC "pouch" with the knives and a few others things.
-
@Huntsman said:
So a bit like all these youtube vids of the experts building SAKs - They make it look so easy!! But it ain'tCan I print this out and give it to my wife? She likes to watch the home improvement shows and gets these wild ideas of doing quick, simple projects that are neither quick, nor simple! :)
To be fair, she learned her lesson a few years ago when she decided we could redo our half bath, knocking out the tile half wall, gutting it down to the floor boards and building it back up. We didn't last a few day before we realized we were in over our heads. Since then she's been much more realistic about what we can or can't do.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login