PowerPint Overview Mighty Little MT
-
I like them both! They have genuine character!
-
Brought my Powerpint in for BO Friday



-
Magentus, your PowerPint looks better every time you show it.

JonesE
-
-
Have not posted much in a while, but I finally decided to replace the scissors on one of my PowerPints. Work great. Also has a few finger tabs and Victorinox tweezers hidden under serrated blade.



-
Nice mod pa. How did you go about that? Vic scissors on a Powerpint really levels it up!
-
Wish I would have took some pic before soldering, but I was not 100% sure I could pull it off. Basically cut the SOG scissors at the base of the lower scissor blade leaving two parallel supports. Then I used a Dremel to open the gap a bit and put in the base of the Victorinox scissors from a donor tool. Took a lot of measurements and attempts, but after my 3rd try it fit perfectly.
-
Here is a closeup of the Victorinox tweezers sitting below serrated blade. Do not interfere with function at all.

-
That looks fantastic pa_strunk!

I have a spare pair of Vic tweezers. I am going to borrow your idea of incorporating the into the PowerPint. They are handy for pulling metal slivers.
JonesE
-
@pa_strunk said:
Wish I would have took some pic before soldering, but I was not 100% sure I could pull it off. Basically cut the SOG scissors at the base of the lower scissor blade leaving two parallel supports. Then I used a Dremel to open the gap a bit and put in the base of the Victorinox scissors from a donor tool. Took a lot of measurements and attempts, but after my 3rd try it fit perfectly.Lovely work!
-
Brought my PP in to work today ready for BO Friday tomoz

-
Those with keen vision (or reading skillz) will notice the broken spring by the serrated blade and the Gerber driver replacing the broken fine slotted driver. All injuries sustained in the line of duty
-
Mags, good job on keeping your PowerPint going. Sucks your spring arm broke. Hopefully, the one on the other side still works. Good job on replacing the broken driver with the Gerber one. Could you share more about it when you get a chance.

JonesE
-
@JonesE said:
Mags, good job on keeping your PowerPint going. Sucks your spring arm broke. Hopefully, the one on the other side still works. Good job on replacing the broken driver with the Gerber one. Could you share more about it when you get a chance.
JonesE
Thanks JonesE . The broken spring doesn't seem to affect the functionality much, though I guess there's more pressure on the remaining one so we'll see how long it lasts
As for fitting the replacement driver, it's from a Gerber 400/600. It drops in nicely with only a little lateral movement. With some fettling on the slot it locks as well.



-
Would you look at that! Nicely done mate

-
-
Thanks Mags, I have often thought of dropping in other implements in place of the stock ones. One of the things holding me back has been the plier jaws when folded closed. Every implement has to fit a certain way to clear the jaw. The other thing is once you got the new tool fitted and everything clears, how do you access it? Essentially, where do you place the nail nick.

JonesE
-
@JonesE said:
Thanks Mags, I have often thought of dropping in other implements in place of the stock ones. One of the things holding me back has been the plier jaws when folded closed. Every implement has to fit a certain way to clear the jaw. The other thing is once you got the new tool fitted and everything clears, how do you access it? Essentially, where do you place the nail nick.
JonesE
Yes, I see what you're saying - it's a very precise setup isn't it.
I quite like that the nail nick problem is solved with the protruding tab of the Gerber driver. It works for me even though it disrupts the silhouette somewhat.What tools would you like to replace and what would you replace then with?
-
The four implements I would change for better ones are: 1. The awl, I want it a little longer and the fact that they cut a portion away at the tip bothers me. 2. The scissors, Mine never could really cut anything. They would jam up if you cut parachord. This one deserves a good rethink. 3. The can opener, the edge needs to be sharpened to actually cut into a can and the little nub should be ground straight and skinnied down to actually be usable as a small flat driver. 4. The bottle opener, the end should be squared off so you can actually use it as a large flat driver.
The last two, a user could simply mod themselves. The first two would take some figuring out.
I really like the tool and they go a lot right with it. For the average user, if they fixed the scissors it would be a home run.
JonesE
-
My needs in a MT are: pliers, 1/4" flat driver, #2 Phillips, knife, scissors.
The PowerPint comes up short on the two drivers. So I ground the end of the file for the flat driver.
Still missing the #2 Phillips.
I removed the can opener, bottle opener, and the little eyeglass driver.
I took a 2 inch #2 Phillips 1/4 hex bit, softened the steel with a propane torch so I could drill a hole in it.
It sticks out of the side a little, that could be fixed by shortening it a little.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login