SAK Stack Challenge 2026
-
David, I'm really sorry to hear that.
Man what a day. Nothing going on with knife usage but that's ok. Took my dog to the vet and she's got a bad heart valve, congestive heart valve and an enlarged heart
So lots of meds for the old girl and hopefully get some time with her. She's not in pain, acts fine thankfully. After that went on a 2 hour drive to take the grandbaby to a doc visit. Pic is from us just chilling in the lot. -
I actually used the scaler one time fishing. I wrapped the body of the knife in a plastic bag and extended the scaler. The hook remover works pretty well, and the scaler gets the job done, but I'd much rather use it as a ruler!
Day 3: Cutting open a bag of fresh coffee with the blade.

-
Day 3
I used CT34 to repair our Kenwood mixer.
It’s about 10 years old and generally trouble free and useful appliance which we use regularly.
But about 4 years ago it suddenly stopped working. I took it to repair shop, they repaired it but it took about a month and cost 75eur. They gave me the faulty part which looked like a little pressure switch. All worked fine again till Tuesday this week - it stopped working again. I remembered the issue so I did some online research and learned that the faulty part was a safety switch that prevents the mixer to run when the head is open. I decided to check whether the issue is the same as previously and see whether I could repair it it by myself.
So the CT34 with the torx bit opened the bottom cover. After some searching (and cursing - it was rather tight space) I was able to locate the switch and removed it from plastic pins on which it sits. And voilà - the plastic body of the switch consist from two parts which were unclicked from each other. I just clicked it together and it worked again! I reinforced it with small piece of duct tape into which I made a hole with awl so it can be put on the pins again. Now it works again!
[attach id=0 msg=2589736]
[attach id=1 msg=2589736]
[attach id=2 msg=2589736]
[attach id=3 msg=2589736]



-
Week 1 Mini Challenge

I decided to try to repair this outlet that's been broken for years. Of course, I had forgotten I already tried to fix it a few years back; it's some kind of issue with the wiring beyond the receptacle. Ah well, I used the screwdrivers, flathead (on the cap lifter) and Phillips (inline).
-
Day 3
Used the mini screwdriver to loosen the temples on my new glasses. The screws were so tight that the nose bridge would bend whenever I opened or closed the temples to put my glasses on or away.
[attach id=0 msg=2589741]
ETA "Day 3"

-
Day 3 bonus, mini challenge
Today I noticed to frequently used kitchen drawer pulls were beyond loose. Actually the utensil drawer pull fell into my hand.
The CHAMPION was assigned duty.
[attach id=0 msg=2589742]And, the half-stop came in handy so I did not need to empty the drawer.
Silverware drawer was checked and its pull was secure. But, across the kitchen my utility drawer pull freely turned.
[attach id=1 msg=2589742]This time, Phillips as an inline driver worked best.
This time, because of the half-stop feature, this single tool worked very well in both configurations.
I also, inspected outlet covers, but decided, new screws are required, as paint has fallen away on many. Estimate a bag of 50 ivory screws should be sufficient😉


-
Everyone. Make sure you number your post for each day. I forget to do it all the time and have to go back. At least I used to. Best wishes. G
:ahhh -
Bay 3 Mini Challenge Bonus
Used the flat driver to replace a broken outlet plate today.

-
I was taught by an electrician many many years ago, that to always align the screw head slot, N/S on switch plate covers and outlet covers.
| = North/South
Never leave the screw head slot in any over position.
Nope \ , /, —. Never.
If tight, then back it off till |, straight up & down.
-
North/South got it. Thanks LC!

JonesE
-
Day 3

Today Champy the SwissChamp accompanied me to an artist talk at a sculpture park, about this sculpture of a giant sturgeon. I made this salt-water etching of the New York City area on a card of stainless steel afterwards, using the scissors on the knife to cut electrical tape.
-
- Gotta put this gifted home made ti pocket clip on Hofritz or I won't carry him too much

[attach id=0 msg=2589773]

- Gotta put this gifted home made ti pocket clip on Hofritz or I won't carry him too much
-
@Barry Rowland said:
David, I'm really sorry to hear that.I'm just glad we've still got time with her. They didn't tell her she needs to be put down so that's good. I cannot tell you how much I love this dog. She's my buddy and I've never met a dog that loves her humans this much. Personality omg and she feels almost human herself someday. She will most definitely be spoiled from now until (she was before). Those who own Mini Schnauzers would completely understand. They're an amazing breed and I've been blessed to have several in my lifetime.
-
@LoopCutter said:
Day 3Yesterday morning I added a SUSPENSION clip to the CRAFTSMAN ( a HANDYMAN with backside Phillips)
And, last night it occurred to me I really should go AWL IN during this challenge. So, this morning I snatched up my crossbody bag and exchanged the SPIRIT MXBS and replaced it with the CRAFTSMAN. I will have pliers yet, and pretty much every thing else. Plus I will leave the COMPACT dangling, because it provides a CORKSCREW!
[attach id=0 msg=2589727]
Love the MX, it's my favorite version of the Spirit. Combining this with another SAK and you feel like you can tackle just about any challenge.
-
Day 3
Trying to figure out why this old speaker stopped working. All the wires and connections seem fine. That's the extent of my expertise though. Champ came in handy for all the screws, and stripping some speaker wire.
-
The batteries corroded in this remote. The 0-1 Phillips on the Work Champ was perfect for the small screws holding the remote together. Some small brushes, a little baking soda mixed with water, some fine sandpaper, compressed air, a little dielectric grease and we're back in business!
[attach id=0 msg=2589779]
[attach id=1 msg=2589779]

-
Day 3
The thing I enjoy with these bigger SAKs is all the implements are at my disposal. The straight line awl is great and a favorite of mine in all the Alox versions. And, my XXL also had one. So handy for pokey and picky things and opening boxes.

-
Day 03
Still using my Champion. Used the awl to vent a cigar.


-
@LoopCutter said:
Congratulations on the new addition!I think I overextended my budget well before this challenge even started.
Thanks! I did too, really.
-
@MrToolJunkie said:
Day 3The thing I enjoy with these bigger SAKs is all the implements are at my disposal. The straight line awl is great and a favorite of mine in all the Alox versions. And, my XXL also had one. So handy for pokey and picky things and opening boxes.

One day I’m gonna have to drop the cash for one of these

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login