Some Basic Tool Truths Everyone Should Be Aware Of
-
Multitool Law #3:
Enjoy the ride and don't deny, if your here, your gonna buy em all anyway!
All Multitools, Brands have their pros and cons.
-
Rust resistance is a key factor unless either you do like rust or live in a non-moist environment (aka the moon).
-
Beyond all these sensible reasons, we should consider aesthetics and ergonomics which I think play a large part in a lot of peoples decision making. I certainly find myself swayed by both and that often leads to trial and error. Oh no, I have to get another tool! >:D
-
When in doubt get a Victorinox.
-
Multi's are a backup device , and rather neat pieces of pocket/belt jewelry . I , and a number of techs I know , find them very usefull for the investigation , and recon stage of a problem/project . They are a lot like small pistols , a good thing to have when you don't have a gun ! And they can deffinately get your sorry azz home , when the colorfull you no what hits the fan .
Well said Sir !
We are a lot like Medieval schollars , arguing about the number of angels on the head of a pin .
And just like in the weapons analogy above , your world has truly turned to poo poo when you are facing a problem and all you have is either a small pistol or a multi .
Chris
-
@american lockpicker said:
@Grant Lamontagne said:
I don't know about that one- I'd take a Flik over an MPT any day...
Def
I agree thats why I put "usually" in there.
Which then pretty much makes your statement useless then does it not?
Here's one, decent tools can be made in any country, including China ;), if good quality and control measures are put in place. When looking at tools, look at the things that matter, not where the thing is made and if you do have concerns, use the search function on the forum and look up the specific tool or start a thread asking about it before ruling it out.
-
Most multitools are made of a stainless steel for convenience (ie rust resistance). Dedicated tools are made of tool steel for durability.
-
Here are some of the things I learned about multitools since I got into them:
1.) All you need is one good multitool but that won't stop you from buying more.
2.) The rule that you pay for what you get also applies to buying new multitool.
3.) If you can't carry your multitool comfortably chances are your multitool will probably end up in your drawer.
4.) If you keep on visiting this forum YOU WILL BUY A NEW MULTITOOL AT LEAST ONE EVERY TWO TO THREE MONTHS. -
@american lockpicker said:
@Grant Lamontagne said:
I don't know about that one- I'd take a Flik over an MPT any day...
Def
I agree thats why I put "usually" in there.
Which then pretty much makes your statement useless then does it not?
Here's one, decent tools can be made in any country, including China ;), if good quality and control measures are put in place. When looking at tools, look at the things that matter, not where the thing is made and if you do have concerns, use the search function on the forum and look up the specific tool or start a thread asking about it before ruling it out.
Not trying to start an arguement but the majority(99%) of junk multitools do come from China its a fact. I started out with knockoffs SAKs and later PSTs and the quality was so bad it made me have no faith in the multitool concept. If your starting out get a Victorinox its made right in Switzerland(best quality in the world) and they have a wide selection of tools for what ever you need and aren't prone to breaking and if something does they have excellent customer service. I'm sure there are now some acceptable chinese tools but why waste your money trying to find one.
-
@american lockpicker said:
@american lockpicker said:
@Grant Lamontagne said:
I don't know about that one- I'd take a Flik over an MPT any day...
Def
I agree thats why I put "usually" in there.
Which then pretty much makes your statement useless then does it not?
Here's one, decent tools can be made in any country, including China ;), if good quality and control measures are put in place. When looking at tools, look at the things that matter, not where the thing is made and if you do have concerns, use the search function on the forum and look up the specific tool or start a thread asking about it before ruling it out.
Not trying to start an arguement but the majority(99%) of junk multitools do come from China its a fact. I started out with knockoffs SAKs and later PSTs and the quality was so bad it made me have no faith in the multitool concept. If your starting out get a Victorinox its made right in Switzerland(best quality in the world) and they have a wide selection of tools for what ever you need and aren't prone to breaking and if something does they have excellent customer service. I'm sure there are now some acceptable chinese tools but why waste your money trying to find one.
Not wanting to get in a China flame war so I will keep my comments brief. Just because it is Chinese does not mean it is crap. Truthfully, China is getting better and better at creating a quality product for very little money. Things that come to mind; Benchmade Red Box knives, Spyderco's Byrd line, Some of Spyderco's main line (Tenacious, Spyderwrench, etc). There are also some very promising steels coming out of China, that will help keep knife and tool costs down, but provide a very workable and durable steel for the end user-us. Every manufacturer wants to make a quality product for as little as possible; one to make more profit, and two to make consumers pick their product over any other. The majority of the sheaths our multi's come in are Made in China, but I wouldn't knock their quality. I am all for making products in the USA, but until they can make them cheaper they will always have a hard time keeping up.
-
- The first rule of multitools. Don't talk about multitools.
Wait scratch that, preach the word! Everyone needs at least one! Everyone I know who didn't think they were useful, I let them carry one of mine for a bit...that changed their tune.
-
@american lockpicker said:
@american lockpicker said:
@Grant Lamontagne said:
I don't know about that one- I'd take a Flik over an MPT any day...
Def
I agree thats why I put "usually" in there.
Which then pretty much makes your statement useless then does it not?
Here's one, decent tools can be made in any country, including China ;), if good quality and control measures are put in place. When looking at tools, look at the things that matter, not where the thing is made and if you do have concerns, use the search function on the forum and look up the specific tool or start a thread asking about it before ruling it out.
Not trying to start an arguement but the majority(99%) of junk multitools do come from China its a fact. I started out with knockoffs SAKs and later PSTs and the quality was so bad it made me have no faith in the multitool concept. If your starting out get a Victorinox its made right in Switzerland(best quality in the world) and they have a wide selection of tools for what ever you need and aren't prone to breaking and if something does they have excellent customer service. I'm sure there are now some acceptable chinese tools but why waste your money trying to find one.
Getting a bit bored with all this now ALP if I am honest. My point was, in a thread headed "Some basic tool truths everyone should be aware of" the advice of "usually...." is not that particularly helpful. We ALL know where you stand on the China thing buddy, so maybe ease up on forcing it all down our necks all the time?
-
@american lockpicker said:
@american lockpicker said:
[quote author=Grant Lamontagne link=topic=15259.msg289617#msg289617 date=1258607363]
I don't know about that one- I'd take a Flik over an MPT any day...Def
I agree thats why I put "usually" in there.
Which then pretty much makes your statement useless then does it not?
Here's one, decent tools can be made in any country, including China ;), if good quality and control measures are put in place. When looking at tools, look at the things that matter, not where the thing is made and if you do have concerns, use the search function on the forum and look up the specific tool or start a thread asking about it before ruling it out.
Not trying to start an arguement but the majority(99%) of junk multitools do come from China its a fact. I started out with knockoffs SAKs and later PSTs and the quality was so bad it made me have no faith in the multitool concept. If your starting out get a Victorinox its made right in Switzerland(best quality in the world) and they have a wide selection of tools for what ever you need and aren't prone to breaking and if something does they have excellent customer service. I'm sure there are now some acceptable chinese tools but why waste your money trying to find one.
Not wanting to get in a China flame war so I will keep my comments brief. Just because it is Chinese does not mean it is crap. Truthfully, China is getting better and better at creating a quality product for very little money. Things that come to mind; Benchmade Red Box knives, Spyderco's Byrd line, Some of Spyderco's main line (Tenacious, Spyderwrench, etc). There are also some very promising steels coming out of China, that will help keep knife and tool costs down, but provide a very workable and durable steel for the end user-us. Every manufacturer wants to make a quality product for as little as possible; one to make more profit, and two to make consumers pick their product over any other. The majority of the sheaths our multi's come in are Made in China, but I wouldn't knock their quality. I am all for making products in the USA, but until they can make them cheaper they will always have a hard time keeping up.
[/quote]Chinese companies are all for business, just give them how much you are willing to buy a product and they will make the product for the price you want inclusive of their cost. Most companies choose to buy at the lowest cost of course quality suffers.
-
So, any more basic tool truths we should all be aware of?
-
Sebenza's are the only thing that will rid evil spirits from a home...its true I saw it on Bladeforums.
-
Must just be the large one's as the wife has no problems living here. :P
-
When I worked as a purchaser for an electronics manufacturing company in BC, Canada, we found places that would provide us superior quality product at lower prices made in China as long as we placed larger orders. The local supplier could not compete with quality, price or lead time on those quantities, so we went with made in China. Any bad parts were refunded provided we proved it was not design related, and actually a manufacturing flaw, in which case they would ship us replacements immediately.
The parts in question were circuit boards, something that is very complex, and can go wrong very easily. The Chinese ones were gold plated contacts and the quality was top notch.
While I'm sure there are manufacturers that have lower standards with even lower prices, sometimes it really is you get what you pay for... if you go for the absolute cheapest, there's probably a good reason.
it's the difference between a box of generic wine and a nice bottle of Gran Reserva Rioja.
-
@andrea.from.roma said:
Rust resistance is a key factor unless either you do like rust or live in a non-moist environment (aka the moon).This is not true.............................................. The moon is not a non-moist environment. :rofl:
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login