byrd wings slippit
-
-
-
I'd be much more tempted if it only had one blade, having the other OH hole sitting under your ring and little finger never looked comfy to me and HH has confirmed it. Also it's a righty only knife as I wouldn't be able to get my (leftie) thumb at the hole what with the other blade sitting in the way.
Please Sal, make a single blade version.

-
-
-
byrd wings slippit update.
ive been carrying this knife every day at work now for a month.
in the initial review my two main gripes were of the ergo of the closed blade and the bent tip of the blade.i noticed that when i opened either of the blades one handed my index finger rested on the other blade, causing me to push the closed blade tip under the choil of the blade i was opening, where you could hear a slight grinding noise, this i found out was the reason for the rolled tip, i now open this knife 2 handed and i no longer get the edge roll.
the design of the knife im also used to now. 90% of my cutting tasks are for no more than a couple of mins at a time, eg open boxes, cut rope, pipe lagging etc. i found that the knife feels quite natural in the hand.
this knife has been used daily, it gets coverd in dirt ,oils and grease, and loads of pocket fluff. and it cleans up well and easily. i have had no problems with any rust issues.
i would feel lost if i didnt have this 2 bladed knife on me, i use the SE for aggressive cutting eg cardboard and rope and cable ties and leave the PE blade for slicing, the PE blade still slices through paper. neither blade has needed to be resharpened as they are holding a good working edge.overall im very pleased with this knife, may be for the 1st week i was trying different grips when cutting but now it feels like any other knife.
would i recommend this knife , yeah. it may not be the best looking or the most comfortable for extended use but it is one hell of a work horse.
(mike, i think this one should deffo go on the xmas want list),heavy handed
-
Thanks for the update mate

-
@heavy handed said:
i noticed that when i opened either of the blades one handed my index finger rested on the other blade, causing me to push the closed blade tip under the choil of the blade i was opening, where you could hear a slight grinding noise, this i found out was the reason for the rolled tip, i now open this knife 2 handed and i no longer get the edge roll.This looks to be a fairly serious defect in the knife's basic design. Guess it could be a manufacturing issue, instead.
Wonder if Spyderco is even aware of this issue.
There was some discussion of rolled tips over on British Blades, but it was attributed to bad steel which seemed unlikely to me.
.
-
ill have to check that thread out, thanks mate

as ringzero says i think it could be a slight design glitch and not a steel problem as the rest of edge on both blades is fine and they have been used daily. -
I've had one since they came out last Spring. I've been pretty much smitten since.
Fit and finish on mine is flawless. Heavy Handed's grinding noise may be due to... heavy handedness. I can replicate the noise, if my fingers rest on the closed blade when opening up the other, by pushing the closed blade laterally so that the "nose" of the closed blade rubs against the jimping on the choil of the opening blade. The grinding noise is the spine rubbing against the jimping. However, it seems I have to be pressing pretty hard on the closed blade to get it to rub all the way down to the edge. Mind you, this happens when I tried to make it happen. Normally, my fingers don't put that much pressure on the closed blade.
One thing that does occur to me is that despite the two blades and four different pocket clip positions, it's not a left hand friendly design. No matter how the clip is positioned, or even if it's removed, the blades are in the wrong position to be opened left handed via thumbholes.
I haven't taken the knife apart, but it seems it may be possible to mod it into an even thinner single blade. As is, it's about as thick as a FRN Native. It seems to have all screw construction. The pivots and scales are held by Torx screws. I presume there's a hidden pin under the scales holding the backsprings. It may also be possible to swap the blade positions to make it southpaw friendly.
-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login