Leatherman disassembly tool.
-
Never know that is a good idea though :D -
I like the idea

-
I like the idea also.

-
I made some of my own sockets , trick is too use cheap sockets.
/topic/7167I think Bob thought the tools were made with a highly speSmurfpillsed electrical cutting/shaping device , to get the knurled pattern imprinted into the tool metal(hard metal). I would be willing to chuck some $ into the kitty too.
Def & Bob I think had some one make some tools & I believe it was a major pain in the rear
-
This maybe a silly question, but has anyone tried replacing the non conventional LM fasteners with binder post and screws?. It would make disassembly easier much like what sog uses. Do they even have binder post/screws available in such small sizes. Might be worth some investigation.
-
@Nutznboltz said:
This maybe a silly question, but has anyone tried replacing the non conventional LM fasteners with binder post and screws?. It would make disassembly easier much like what sog uses. Do they even have binder post/screws available in such small sizes. Might be worth some investigation.Actually a guy talked about in in the Mod Squad forum
He swapped out the knurled screws on a LM Super Tool here's the link and also I believe he gave a link on where he got the hardware as well :D/topic/3473
-
I disassembled fuse with Powerlock and Spirit.
-
To actually cut the fancy "star" pattern into a piece of steel requires a wire EDM machine, which I don't have access to :(
Even if someone did have a wire EDM available, the process itself is relatively slow (read "expensive"). So I doubt the economics would work out. Tools could be made, but they would be more expensive than most members here would be willing to pay. :-\
-
@J-sews said:
To actually cut the fancy "star" pattern into a piece of steel requires a wire EDM machine, which I don't have access to :(Even if someone did have a wire EDM available, the process itself is relatively slow (read "expensive"). So I doubt the economics would work out. Tools could be made, but they would be more expensive than most members here would be willing to pay. :-\
:o That probably means it would cut to deep into my MT fund :ahhh :D
-
I know this is an old topic, but I'm wondering if I might be successful making a socket for the PST using J-B Weld. It would seem rather simple to make the socket from an old socket just by filling the socket with J-B Weld, and then pushing the knurled fastener head into the J-B Weld, pulling it out - leaving the impression, and then after some drying time it would be a perfect fit. Has anyone tried this, or foresee any problems?
-
I say give it a whirl Skunky
.The only problem I can think of is the star pattern is very shallow
I wonder if the JB Weld imprint might crumble in use
.
I have not used JB Weld , but looking at their website it sure looks interesting.How easy would it be to clean the fastener used to imprint the pattern, or would the fastener be trashed

hop to it mate :D :D :D Keen too hear how it goes mate. :D :D -
I'll give it a try and let ya'll know how it goes.
-
I have been giving it a bit more thought :D :D
Does JB Weld's consistency enable it to take the fastener imprint, that is does it go like putty so you could push the fastener into it & leave a print.Or is it more of a liquid/semi liquid consistency
.
You could always use some kitchen wrap (Glade Wrap) around the fastener & leave it in the JB as it hardened. Hopefully the glade wrap would enable you to remove the fastener from the hardened JB
.Not sure if the glade wrap would help to leave a good print though

Good luck mate
:D :D -
J-B Weld may be a little too soft to make the impression when first mixed. I'm going to have to babysit the mixed J-B Weld and test the impression quality over an hour or so. If I can't get a good impression, I might try the plastic wrap as you suggest, or possibly some flour... I work two jobs, but will try this tomorrow night if I can get the time.
-
@skunkbad said:
I know this is an old topic, but I'm wondering if I might be successful making a socket for the PST using J-B Weld. It would seem rather simple to make the socket from an old socket just by filling the socket with J-B Weld, and then pushing the knurled fastener head into the J-B Weld, pulling it out - leaving the impression, and then after some drying time it would be a perfect fit. Has anyone tried this, or foresee any problems?i would say go for it, as i have a lot of faith in J-B weld, i used it on a cylinder head on one of my old motorbikes once to get out of trouble as i had a big hole in it, it lasted for 2 years and TBH i scraped the bike and not because of the head , iva also used it to repair old watch cases,
paul
-
@skunkbad said:
J-B Weld may be a little too soft to make the impression when first mixed. I'm going to have to babysit the mixed J-B Weld and test the impression quality over an hour or so. If I can't get a good impression, I might try the plastic wrap as you suggest, or possibly some flour... I work two jobs, but will try this tomorrow night if I can get the time.Good luck mate
. I might see if I can find some JB weld myself :D :D. -
would a cnc be any good for making one or not?
-
@J-sews said:
To actually cut the fancy "star" pattern into a piece of steel requires a wire EDM machine, which I don't have access to :(Even if someone did have a wire EDM available, the process itself is relatively slow (read "expensive"). So I doubt the economics would work out. Tools could be made, but they would be more expensive than most members here would be willing to pay. :-\
would a laser cutter be able to cut the shape out of a piece of sheet metal effectively? to make some sheet metal wrenches, like the wrenches SOG used to sell.
-
I would definitely be interested in owning a good set of these if anyone figures a good way to fabricate them.
-
What tools are needed to disassemble a LM? I thought it was simply the security torx bit.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
