What Did You Use Your Multitool For Today?
-
Finally I get to write something that I think is noteworthy.
I use my MT pretty much everyday for little stuff nothing major but today was different.
Today I went to Goodwill and found a printer stand in good condition for $9.00 so when I put it in my cart
(which is too small) it stuck out so it was hard to move around aisle and people.So I got the bright idea of taking it apart with my ST 300. Turned a couple screws here and there and now I have four
pieces that fit nicely in my cart.People looked at me a little strange but that's okay I got my stand and got out of the store without breaking anything or injuring anyone.
-
My friend was giving me a tour of his property, and while we were walking we happened upon a spot that required us to duck very low under some mesquite branches. I pulled out my spirit and used the fantastic saw on it for the first time and cut back 5 or 6 branches, all between 1 and 3 inches thick. The spirit performed great. I also used the pliers later to lift a barbeque griddle into place and used the flathead/bottle opener to open our beers. I love this tool.

-
@Swiss Man said:
Finally I get to write something that I think is noteworthy.I use my MT pretty much everyday for little stuff nothing major but today was different.
Today I went to Goodwill and found a printer stand in good condition for $9.00 so when I put it in my cart
(which is too small) it stuck out so it was hard to move around aisle and people.So I got the bright idea of taking it apart with my ST 300. Turned a couple screws here and there and now I have four
pieces that fit nicely in my cart.People looked at me a little strange but that's okay I got my stand and got out of the store without breaking anything or injuring anyone.
Always a good indicator of a successful shopping trip.

:D
-
@gadgetguy35 said:
My friend was giving me a tour of his property, and while we were walking we happened upon a spot that required us to duck very low under some mesquite branches. I pulled out my spirit and used the fantastic saw on it for the first time and cut back 5 or 6 branches, all between 1 and 3 inches thick. The spirit performed great. I also used the pliers later to lift a barbeque griddle into place and used the flathead/bottle opener to open our beers. I love this tool.
but I still prefer the bottle opener on my skeletool cx. :D -
Used my new LM Charge TK (titanium Kwakster :D) to do a few bits on my car this morning. Pliers, blades and phillips all got a good work out.

-
working on a pouch for the core, so used a few MT's :D
paul

-
cutting the end off a mastik tube
whats a good stone for sharpening my charges knife its beginning to get in need of some attention
-
-
I used my Gerber Octane clamshell package opener blade to open up a new Gerber Grappler package. It worked great, much better than a knife blade tip. I was able to open the Grappler clamshell with no damage to the cardboard inside. Most of the time they get sliced up badly in my case.
Then when I got home, I used the Grappler to squeeze a bottle cap down to the size of a dime. Just testing it out, you know.
-
I used a Suspension to open a clamshell containing a new Octane. :)
And now you have a clamshell opener.
Yup, used it today to open a Grappler clamshell.
-
Then when I got home, I used the Grappler to squeeze a bottle cap down to the size of a dime. Just testing it out, you know.
[/quote]So, aside from bottle caps, what do you think of it? Should I replace my Crunch?
-
I used a Spirit to loosen some cable fittings, and the SAK Explorer to open some shipping containers.

-
pulled the old little fence down today as have lots of plans for our little garden, :D
mini crow bar and the core ,

all pulled down

-
Paul, you've got a Core, what the heck do you need a mini crow bar for

-
I used my wave and piranha to adjust the tilt on a LCD TV hanging in my dad's room at the hospital. It really needed a hex bit and a wrench but I had to improvise seeing I didn't have my LM bit kit on me.
-
Used a Crunch and Skeletool to tighten up a bolt on a Mirca. Now I`m rusty
ready! -
Used my Sideclip to pull, pry, cut ect... Same stuff as always.. :)
-
Used the prybar/screwdriver/bottle opener on the Spirit as an ice pick to chip the couple inches if ice out of my trunk. Used the PE blade to cut the carpet out. Leaking trunks suck lol.
-
More of the same project, Spirit got a lot of use. After pulling the car's spoiler off I used the chisel/scraper to remove the old crap that was failing to seal around the spoiler. Used the awl to drill a small hole in the bottom of the spoiler to drain the half gallon of water out of it. Apparently Canadiens fail at making spoilers lol

-
@thebullfrog said:
More of the same project, Spirit got a lot of use. After pulling the car's spoiler off I used the chisel/scraper to remove the old crap that was failing to seal around the spoiler. Used the awl to drill a small hole in the bottom of the spoiler to drain the half gallon of water out of it. Apparently Canadiens fail at making spoilers lol
It's a spoiler not a fin, eh? Silly Canadians and their hockey skillz.
LOL, I love our northerly neighbors, and all the ones I work with give me hell all the time. Great folks!
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login