What Did You Use Your Multitool For Today?
-
cutting the end off a mastik tube
whats a good stone for sharpening my charges knife its beginning to get in need of some attention
-
-
I used my Gerber Octane clamshell package opener blade to open up a new Gerber Grappler package. It worked great, much better than a knife blade tip. I was able to open the Grappler clamshell with no damage to the cardboard inside. Most of the time they get sliced up badly in my case.
Then when I got home, I used the Grappler to squeeze a bottle cap down to the size of a dime. Just testing it out, you know.
-
I used a Suspension to open a clamshell containing a new Octane. :)
And now you have a clamshell opener.
Yup, used it today to open a Grappler clamshell.
-
Then when I got home, I used the Grappler to squeeze a bottle cap down to the size of a dime. Just testing it out, you know.
[/quote]So, aside from bottle caps, what do you think of it? Should I replace my Crunch?
-
I used a Spirit to loosen some cable fittings, and the SAK Explorer to open some shipping containers.

-
pulled the old little fence down today as have lots of plans for our little garden, :D
mini crow bar and the core ,

all pulled down

-
Paul, you've got a Core, what the heck do you need a mini crow bar for

-
I used my wave and piranha to adjust the tilt on a LCD TV hanging in my dad's room at the hospital. It really needed a hex bit and a wrench but I had to improvise seeing I didn't have my LM bit kit on me.
-
Used a Crunch and Skeletool to tighten up a bolt on a Mirca. Now I`m rusty
ready! -
Used my Sideclip to pull, pry, cut ect... Same stuff as always.. :)
-
Used the prybar/screwdriver/bottle opener on the Spirit as an ice pick to chip the couple inches if ice out of my trunk. Used the PE blade to cut the carpet out. Leaking trunks suck lol.
-
More of the same project, Spirit got a lot of use. After pulling the car's spoiler off I used the chisel/scraper to remove the old crap that was failing to seal around the spoiler. Used the awl to drill a small hole in the bottom of the spoiler to drain the half gallon of water out of it. Apparently Canadiens fail at making spoilers lol

-
@thebullfrog said:
More of the same project, Spirit got a lot of use. After pulling the car's spoiler off I used the chisel/scraper to remove the old crap that was failing to seal around the spoiler. Used the awl to drill a small hole in the bottom of the spoiler to drain the half gallon of water out of it. Apparently Canadiens fail at making spoilers lol
It's a spoiler not a fin, eh? Silly Canadians and their hockey skillz.
LOL, I love our northerly neighbors, and all the ones I work with give me hell all the time. Great folks! -
I used my surge for sewing...
??? What?
-
I used my Squirt P4's pliers to extricate a MicroSD to SD card adapter from my printer; apparently the card has to be pushed in almost entirely in order to be read or written to, at which time there is so little actual material left outside of the card reader portion of my printer as to make it impossible to remove using my fingers, so P4 to the rescue... plus, it allows me to use very gentle force much easier than what I think my Spirit X would allow. ^^
But yeah, why the crap would the printer's scanner only allow scanned images to be copied onto a media card or to be printed... yet doesn't have the option to send the file to the computer with which it is currently connected? HP, you've done it again.
Plus, after looking at a drawing of my apartment next year, I may end up having to get an even smaller printer - there's simply no room in my bedroom for a printer of this size, which is saying something, because my current printer is roughly two-thirds(!) the size of my previous printer. @_@ -
Time for a typewriter?
-
I used my Victorinox Elmer to cut the excess tape of my new moustache bars on my tourer :)
-
Surge came off the bench today and built me a coffee table :D
-
The little quatro-screwdriver from the SwissCard came out to tighten some screws on the front door today.

That's the only tool action I've had for quite some time.
It's actually a pretty decent driver... :D
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login