LM bit driver
-
@Magic Bus said:
A aaaa aa aa nnnn dd ............ there goes the thread!! Ben and Mike, you're both so totally predictable
>:( :D Gareth thanks for being the only sensible Brit here ;) Replacing the bit changer with a dedicated phillips is good but I wonder if I could somehow get another flat driver in instead of the little bit changer?i always thought they were the same width
-
@Magic Bus said:
A aaaa aa aa nnnn dd ............ there goes the thread!! Ben and Mike, you're both so totally predictable
>:( :D Gareth thanks for being the only sensible Brit here ;) Replacing the bit changer with a dedicated phillips is good but I wonder if I could somehow get another flat driver in instead of the little bit changer?i always thought they were the same width
Sorry, by little I meant the bit changer with the little driver
-
@Magic Bus said:
A aaaa aa aa nnnn dd ............ there goes the thread!! Ben and Mike, you're both so totally predictable
>:( :D Gareth thanks for being the only sensible Brit here ;) Replacing the bit changer with a dedicated phillips is good but I wonder if I could somehow get another flat driver in instead of the little bit changer?thats a great idea Chris, i will never use that little driver,

Trouble is the bit changer is thicker than a flat driver

-
@Magic Bus said:
@Magic Bus said:
A aaaa aa aa nnnn dd ............ there goes the thread!! Ben and Mike, you're both so totally predictable
>:( :D Gareth thanks for being the only sensible Brit here ;) Replacing the bit changer with a dedicated phillips is good but I wonder if I could somehow get another flat driver in instead of the little bit changer?thats a great idea Chris, i will never use that little driver,

Trouble is the bit changer is thicker than a flat driver

yeah i just looked and its a lot thicker :-\ you would almost loose all the tools on that side

-
@Magic Bus said:
A aaaa aa aa nnnn dd ............ there goes the thread!! Ben and Mike, you're both so totally predictable
>:( :D Gareth thanks for being the only sensible Brit here ;) Replacing the bit changer with a dedicated phillips is good but I wonder if I could somehow get another flat driver in instead of the little bit changer?Might be able to help with that as well.
Yes it's a bit thicker than the small bit holder but you could thin it out without loosing any functionality. -
@Magic Bus said:
A aaaa aa aa nnnn dd ............ there goes the thread!! Ben and Mike, you're both so totally predictable
>:( :D Gareth thanks for being the only sensible Brit here ;) Replacing the bit changer with a dedicated phillips is good but I wonder if I could somehow get another flat driver in instead of the little bit changer?Might be able to help with that as well.
Yes it's a bit thicker than the small bit holder but you could thin it out without loosing any functionality.Thankyou :D I'm gonna make a Franken Wave >:D
-
@Nikos said:
The pub is always a good way of solving such problems...
:DSeriously now, if the recessed screws don't have enough space around them for LM's bit driver system, they'll likely not have enough space around them for the extender either. If it's just a matter of depth, go with the extender. For a better all-around solution, go with the Spirit (oh Dave...
:D) Or go down the dark alley and mod a long LM phillips into your Wave.You rang?
At least with recessed screws the Spirits drivers are less likely to slip off and cause injury :P (Only joking).
I don't have a bit extender so can't say really :)
-
I have both Wave and Spirit and also the extender for Skele/Wave/Charge and Ratchet with extension bar. The LM extender wobbles in both Skele and Wave and the smaller bits don't sit well in the standard end of the adapter. My vote goes for Spirit X with ratchet and extension bar

p.s. LM adapter rusts :D (mine really did)
-
I had a go at modding a extension for a wave, it worked out ok ,
/topic/19108
-
That looks good Paul
Thanks for the advice everyone, I'm off to the pub ;) -
A bike.. oh no, way to dangerous I fall off them :D
-
It wouldn't be a pub bike if it had brakes

-
@Benner said:
Why get the Spirit ??? True the driver may reach, but it would just keep slipping out anyway. :PThis is very true. While I praise Vic for their beautiful tools, they often stay at home because none of them grip worth a darn. That is the only good thing about LM's new beadblast everything rule. All the implements grab and hold on. I really dig that wave mod, I may do that to one down the road.
-
Presumably flattening the little tabs in the handles just makes the Wave a bit harder to close?
-
I'm considering attacking this problem by hacking up a set of MUT bits when they finally come out. Chop those crazy-long bits in two, and make two considerably-longer LM flat bits out of them. The only reason I'm considering cutting them in two is to reduce some mechanical advantage that might bust my Wave, and so that I could more easily thin out the shaft to be the same width as the screwdriver head, meaning they'd fit better in some recessed areas.
Entirely theoretical at this point, as I don't have the bits, and I don't know if any of my tools would cut them if I did :P
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login