LM bit driver
-
That looks good Paul
Thanks for the advice everyone, I'm off to the pub ;) -
A bike.. oh no, way to dangerous I fall off them :D
-
It wouldn't be a pub bike if it had brakes

-
@Benner said:
Why get the Spirit ??? True the driver may reach, but it would just keep slipping out anyway. :PThis is very true. While I praise Vic for their beautiful tools, they often stay at home because none of them grip worth a darn. That is the only good thing about LM's new beadblast everything rule. All the implements grab and hold on. I really dig that wave mod, I may do that to one down the road.
-
Presumably flattening the little tabs in the handles just makes the Wave a bit harder to close?
-
I'm considering attacking this problem by hacking up a set of MUT bits when they finally come out. Chop those crazy-long bits in two, and make two considerably-longer LM flat bits out of them. The only reason I'm considering cutting them in two is to reduce some mechanical advantage that might bust my Wave, and so that I could more easily thin out the shaft to be the same width as the screwdriver head, meaning they'd fit better in some recessed areas.
Entirely theoretical at this point, as I don't have the bits, and I don't know if any of my tools would cut them if I did :P
-
@SlackOne said:
I'm considering attacking this problem by hacking up a set of MUT bits when they finally come out. Chop those crazy-long bits in two, and make two considerably-longer LM flat bits out of them. The only reason I'm considering cutting them in two is to reduce some mechanical advantage that might bust my Wave, and so that I could more easily thin out the shaft to be the same width as the screwdriver head, meaning they'd fit better in some recessed areas.Entirely theoretical at this point, as I don't have the bits, and I don't know if any of my tools would cut them if I did :P
A dremel with a cutting wheel on it will cut any MT steel there is. Get the reinforced ones, they last awhile.
-
i thought the bits were a bit tougher then MT steel?
-
You will find that a grinder will cut anything depending on the disk ;)
-
-
i thought the bits were a bit tougher then MT steel?
They are tool steel, and harder than the rest of the tool, but any cutting disk will go through them like butter. I just suggested dremel because it is small and you have a greater dexterity than a 3 inch cutting disk.
i find my dremel grinds pretty much everything, great little tools

-
i thought the bits were a bit tougher then MT steel?
They are tool steel, and harder than the rest of the tool, but any cutting disk will go through them like butter. I just suggested dremel because it is small and you have a greater dexterity than a 3 inch cutting disk.
i find my dremel grinds pretty much everything, great little tools

I love mine, don't know what I would do without it.
-
i thought the bits were a bit tougher then MT steel?
They are tool steel, and harder than the rest of the tool, but any cutting disk will go through them like butter. I just suggested dremel because it is small and you have a greater dexterity than a 3 inch cutting disk.
i find my dremel grinds pretty much everything, great little tools

I love mine, don't know what I would do without it.
for a long time i built custom diecast models and the dremel is a really handy tool for this,


-
Those are sweet, Zed! I used to build model ships, but I got out of it when my son was born. Too many small pieces around the house. I have to keep my hobbies contained to the garage.
-
@gadgetguy35 said:
Those are sweet, Zed! I used to build model ships, but I got out of it when my son was born. Too many small pieces around the house. I have to keep my hobbies contained to the garage.cheers mate , i built mainly muscle cars and movie stuff, and i built a lot of general lee's :D
here are some of the 30 year old tin plate charger i did , i loved getting these as most was in very poor shape, the end one was being stripped down at that time of this pic, the F&F charger was one of my favorite projects i did, these are very big 1:16th scale,

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
