Case to replace Victorinox
-
Neil,
Good for you bud, nice #18 pattern stockman you got. While SAK's are all fine and good I am of the opinion for everyday cutting chores nothing beats a well made traditional slippie......and you can't go wrong with a Case.

Though be careful, slippies can be addicting.....particularly Case's and the like.
And might I add, if you every get the hankering to go up a notch with another stockman give Case's larger #75 pattern a look. One like this Silverscript piece..........

..............these'll spoil ya! ;)
2xTap
-
Great work on that blade Neil. :)
-
Good for you bud, nice #18 pattern stockman you got. While SAK's are all fine and good I am of the opinion for everyday cutting chores nothing beats a well made traditional slippie......and you can't go wrong with a Case.

Though be careful, slippies can be addicting.....particularly Case's and the like.
And might I add, if you every get the hankering to go up a notch with another stockman give Case's larger #75 pattern a look. One like this Silverscript piece..........
...
..............these'll spoil ya! ;)
2xTap
I thought you'd approve of my little experiment :D
Now quit showing me lovely looking knives that I can't afford ;)This evening the Case has been doing packaging duty.
This brings up a discussion Gareth and I had the other week, how sharp is sharp enough. For me if a blade can slice through a sheet of bubblewrap without snagging its sharp enough.
Well the newly repaired sheepsfoot blade accomplished that without issue and then went on to the slightly more arduous task of slicing up corrugated cardboard. I've got it set presently with a thirty degree bevel so it'll be interesting to see how long that holds up. I would have been better using the clip blade for the bubblewrap but it wasn't quite sharp enough, tomorrow I'll give its edge a tickle :)Thanks Ben, you'll be able to check it out in person next weekend

-
Wow!
How do you reprofile blades? I am unfamiliar with the methods. Tis brilliant!
-
I use sharpening stones. Much slower than hitting it with a Dremel but you don't have to fret about mucking up the temper and because you're working slower you're also less likely to make a mistake and muck it up :)
-
You have patience, I'd throw it on a belt sander.
-
Nice repair job as always Neil.
I've been carrying a very similar Case Stockman on and off for a couple of weeks now, while I don't think it's replaced a SAKs' special place in my heart there's no doubt it's a cracking knife. :)
-
I love Case knives. I always have some kind of slippie on me and a little sak. :sak:
-
Nice knife Gareth
Do you ever use the spey blade? If so what for? So far its the blade that has seen no use. -
@Neil said:
Nice knife Gareth
Do you ever use the spey blade? If so what for? So far its the blade that has seen no use.The spey blades always seem to end up as my beater blade. It doesn't get used in too many cutting chores but when I have to scrape something or dig at something I'll pull out the spey blade. It doesn't get the acute sharp edge my other blades get. I keep the clip point sharp for food chores and pointy cutting. The sheepsfoot is by far my most used blade shape. For utility work the sheepsfoot is outstanding.
-
great work on that blade neil, lovely knife

-
How are you getting along with it v a SAK so far then Neil?
-
Nice work on the blade there Neil.
That Case you posted and 2taps are beauts! The only thing I have with
most SAKS and knives of that size is that I'm into a sheath carry. I'd love to pocket them but they are just way
to uncomfortable for me for any length of time. -
Back in Jurassic times ( the sixties ) I used to rock Case slippies , usually Stockman patterns and most especially Trappers . Preference eventually went to Trappers . The Spey long Spey kept almost razor like , and the Turkish clip for chores . With Stockmen , the Spey never got any lovin , it was just the clip and the sheepsfoot . The Sheepsfoot doing the dirty work .
Chris
-
@Neil said:
Nice knife Gareth
Do you ever use the spey blade? If so what for? So far its the blade that has seen no use.Actually no, not much. My "go too" blade seems to be the sheepsfoot more than the other two. Partly as the nail nick is positioned well for a left hander, party because it makes for a more comfortable grip if the sheepsfoot is deployed out of the way.
-
Nice knife Gareth
Do you ever use the spey blade? If so what for? So far its the blade that has seen no use.Actually no, not much. My "go too" blade seems to be the sheepsfoot more than the other two. Partly as the nail nick is positioned well for a left hander, party because it makes for a more comfortable grip if the sheepsfoot is deployed out of the way.
You need a good 2 or 4 blade congress if the sheepsfoot is you fav blade as it is mine :D
Neat experiment Neil
BTW I carry a slippie all the time (4 blade congress ;) ) but I carry an Executive for the scissors and file that way I get the best of both worlds 
-
Well so far for cutting tasks I've been very pleased with the case. I think if I were to buy one of my own I'd go for a two blade model though.
As expected the lack of other tools has proven problematic. But knowing this would happen I've had SAKs on standby around the place :D
-
Paired with a MT though and you'd be good to go.
A knifeless Fuse is a goodun for that combo and for us UK folk.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login