SuperJuice KFS4
-
@J-sews said:
Thanks for the encouragement all, but it really doesn't count unless the tool actually gets finished right? :DOn which note, another stumbling block seems to be the stainless steel used in the pivot pins. For some reason it galled up and burred rather quickly on the pre-assembly I did yesterday.
With each open and close of the knife blade, the amount of "drag" became noticably worse. (not sure if the drag marks show up well in this picture)The new (longer) ones will have to be made from brass. And hopefully brass will be strong enough for plier usage. :-\
If the blade would damage the SS screw wouldn't brass be damaged even faster? Take a look at the blade pivot hole, maybe it was damaged to create a burr. Also try polish the inner surface of the pivot.
-
Thanks for the encouragement all, but it really doesn't count unless the tool actually gets finished right? :D
On which note, another stumbling block seems to be the stainless steel used in the pivot pins. For some reason it galled up and burred rather quickly on the pre-assembly I did yesterday.
With each open and close of the knife blade, the amount of "drag" became noticably worse. (not sure if the drag marks show up well in this picture)The new (longer) ones will have to be made from brass. And hopefully brass will be strong enough for plier usage. :-\
If the blade would damage the SS screw wouldn't brass be damaged even faster? Take a look at the blade pivot hole, maybe it was damaged to create a burr. Also try polish the inner surface of the pivot.
The blade pivot hole looks really smooth J. :-\ I'll try polishing it of course. But what I've found on some of the original stainless steel firearms from the early 1970's is that certain stainless-on-stainless moving parts just tend to naturally gall, especially if they happen to be the same "grade" of material. Nowadays they tend to make parts that rub against one another out of two different grades to avoid galling. So I'm hoping brass pivots will work better, even though they will be weaker than the steel ones.
I'll test it first of course. :-\
-
-
That could be too, one of my wenger ranger has the main blade grind horribly against the lock liner for no apparent reason.
Given your vast resources, could you make one out of 300 series SS, or even titanium?
-
@jzmtl said:
That could be too, one of my wenger ranger has the main blade grind horribly against the lock liner for no apparent reason.Given your vast resources, could you make one out of 300 series SS, or even titanium?
My vast resources coughed up a piece of brass pin stock. I'm gonna try that first :D
-
so hows the problem over coming going?
-
@Spork, Lord of Lime Jello! said:
How about countersinking the other side of the blade and riveting the thumbstud in place...like a Victorinox bushing?If you countersink something that thin on both sides, you end up with a sharp edge in the middle. In order to get a smooth edge, he would have to counter-bore both sides, but it wouldn't be deep enough for the rivet to sit flush and retain it's strength.
I would go with a countersink on the backside of the blade for a screw, and thread the thumbstud ala kershaw knives.
But, Bob is the master, and unlike me, he has actually started his mod(s) whereas mine sits on the drawing board. Kudos Bob, those scales look sweet! I gotta get a mill, it's killing me that I can't machine my stuff in my shop, I have to wait until a CNC is free at my Uncle's foundry(which is never).
-
Does look sweet bob hope you sort the problem out sure you will, and this is one LM that needs a clip

paul
-
Wow, you sure got some talent.
What tools are you using?Perhaps we should start making the perfect Multitool.org Multi all together.

-
He's sickeningly good at this isn't he?
:D
-
Yep, makes me wish I went into tool making :D
-
I'm not a machinist, so there might be an obvious answer, but would some grease/lube be useful in preventing the galling?
-
Damn I'm impressed! Other than being able to spell "titanium" I wouldn't have the slightest idea of where to start something like that. Nice work buddy!

-
@J-sews said:
Then things were proceeding nicely again, until it became apparent that my pivot screws are too short. :'( The ones I bought from www.knifekits.com are one half inch long:
Unfortunately, it appears they need to be just a little bit longer. :( These are already the longest ones knifekits sells, so I'll have to make my own.
Just curiously, what diameter are the pivot pins?
I have a coupla semi-børked Juices, and have been considering a layer mod, and really REALLY didn't wanna have to deal with peening pins!
(Before anybody asks: Knife, Scissors+Bottle Opener, Saw (yes, saw)+Awl, File. No serrated knife, no freakin' corkscrew. Basically, a KF4 with scissors instead of the serrated blade.)
I'm betting they're prolly some 300-series stainless. Too bad you couldn't harden them...
-
AMAZING!
-
@MultiMat said:
WOWSERS Bob , that is looking Brilliant

I have been wondering about how hard it would be to put a thumb stud on a Buck110 I have on the way. Sounds a bit tricky :(
Bob GREAT work mate

You have seen these right? I have some and they work great on my 110's.
http://www.britishblades.com/forums/showthread.php?89890-EZ-Stud
-
WOWSERS Bob , that is looking Brilliant

I have been wondering about how hard it would be to put a thumb stud on a Buck110 I have on the way. Sounds a bit tricky :(
Bob GREAT work mate

You have seen these right? I have some and they work great on my 110's.
http://www.britishblades.com/forums/showthread.php?89890-EZ-Stud
No I have not :o.
Thanks Sean I will try & track one down mate

BTW BOB what is going on with the project

-
WOWSERS Bob , that is looking Brilliant

I have been wondering about how hard it would be to put a thumb stud on a Buck110 I have on the way. Sounds a bit tricky :(
Bob GREAT work mate

You have seen these right? I have some and they work great on my 110's.
http://www.britishblades.com/forums/showthread.php?89890-EZ-Stud
No I have not :o.
Thanks Sean I will try & track one down mate

BTW BOB what is going on with the project

Nothing. :-\ Not one darn iota of progress in the last month, due to all the equipment at work being tied up on "company business." ::) (sigh) But I'll be back on it soon enough. :)
-
@J-sews said:
Then things were proceeding nicely again, until it became apparent that my pivot screws are too short. :'( The ones I bought from www.knifekits.com are one half inch long:
Unfortunately, it appears they need to be just a little bit longer. :( These are already the longest ones knifekits sells, so I'll have to make my own.
Just curiously, what diameter are the pivot pins?
I have a coupla semi-børked Juices, and have been considering a layer mod, and really REALLY didn't wanna have to deal with peening pins!
(Before anybody asks: Knife, Scissors+Bottle Opener, Saw (yes, saw)+Awl, File. No serrated knife, no freakin' corkscrew. Basically, a KF4 with scissors instead of the serrated blade.)
I'm betting they're prolly some 300-series stainless. Too bad you couldn't harden them...
The Juice pins are 5/32 (or .156") in diameter. Unfortunately though, they are just slightly too short to work on a tool of Kf4 thickness. :( You would have to drop one whole layer in order for these pins to work. >:(
I'm not willing to do that, so I'll be making my own (longer) ones out of brass. I'll crank out a few extras if you want. :)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login