marbles 'safety axe'
-
@Spork, Lord of Lime Jello! said:
@Mike, Lord of the Spammers! said:
That's a lovely looking hatchet alright

I'd soak it in linseed oil rather than water though mate, and probably put a new wedge in to

Wedging wouldn't have done any good on the No.5s I have...the eyes aren't even tapered. The head of the top one slid off before I even used it...they were only supposed to be "cosmetic" seconds when I bought them from SMKW. The other seemed to stay on, but to be on the safe side I drilled a hole through the head to put a steel pin through it.
That must of taken a while :o
-
@Spork, Lord of Lime Jello! said:
@Mike, Lord of the Spammers! said:
Wedging wouldn't have done any good on the No.5s I have...the eyes aren't even tapered. The head of the top one slid off before I even used it...they were only supposed to be "cosmetic" seconds when I bought them from SMKW. The other seemed to stay on, but to be on the safe side I drilled a hole through the head to put a steel pin through it.thanks for the pics spork

your #5s have different handles than my #6. the 6 has fluting cut into the handle where it joins into the bit. also, the bit has reverse flutes cut into the axehole (i've always wanted to say that). the blade gaurd sits completely within the handle on mine and does not extend past the end of the handle. -
@Mike, Lord of the Spammers! said:
@Spork, Lord of Lime Jello! said:
@Mike, Lord of the Spammers! said:
That's a lovely looking hatchet alright

I'd soak it in linseed oil rather than water though mate, and probably put a new wedge in to

Wedging wouldn't have done any good on the No.5s I have...the eyes aren't even tapered. The head of the top one slid off before I even used it...they were only supposed to be "cosmetic" seconds when I bought them from SMKW. The other seemed to stay on, but to be on the safe side I drilled a hole through the head to put a steel pin through it.
That must of taken a while :o
It actually didn't :P
I believe that many axe heads are hardened only on the cutting bit portion, leaving the eye softer for toughness. I know it was an acceptable practice to bury the edge in soil to burn out a broken handle in the past.
-
Funny thing is you pay a lot to get a differential temper these days ::)
-
@Mike, Lord of the Spammers! said:
It's been a good field tool so far mate :) I still reckon the head's made of iron judging by the weight :DCertainly earned it's keep

Good to know Mike, I'll admit it was the weight that made me pass it on. It's a big head on a short shaft IMO (oo-er), but a very nice hatchet none-the-less.
-
after soaking in linseed oil i used the hachet on a piece of 4" oak. halfway through the bit had nearly slipped completely off the handle. what a POS.... i'm trying some j b weld on it to try and make it servicable. i see exactly why these things are crap now. theres nothing for the handle to grip to making it completely unreliable.
i checked out some hachets at lowes yesterday. looks like you can get a decent hatchet for less than $20 that look to be darn near indestructable.
-
Have you used a wedge?
-
heck no.... what kind of a redkneck do you think i am :D .... live and learn. the linseed oil worked great on my axe and maddox and they are much older.
i used the origional wedge which is the only thing that kept the bit from flying completely off the handle. that j b weld is wicked stuff. if that does'nt hold nothing will.
-
Best not use the axe near anyone you like till its fixed then :D
-
:D
-
Might want to take it over to the in-laws and chop a few cord for them though >:D
-
sweet...... the j b weld worked!
i chopped through the remainder of the log and another full chop through again with absolutely no issues. the bit is rock solid now. the marbles in no longer a POS. now it is a POS that reliably works. edge retension looks good but i think i need to take out some of the acute angle cause you get just a bit of rollover. it literally shaved the hair on my arm before i started the chop
for what it is i'm ok with it but i think i would rather the handle be a little longer and the head a good bit heavier. -
JB Weld to the rescue again!

-
What an interesting blade cover. It'd be interesting to play with one of these but I'm having difficulty believing that the metalwork in the handle wouldn't become painful with sustained/regular use.

What is JB Weld?
-
@Hedge Kid said:
What an interesting blade cover. It'd be interesting to play with one of these but I'm having difficulty believing that the metalwork in the handle wouldn't become painful with sustained/regular use.
What is JB Weld?TBH 5-10 minutes with this thing is about all i can take. not b/c of the blade guard in the handle unfortunately. i notice it only rarely and it is not painful at least to me.
j b weld is an epoxy with incredible holding power. it was my last resort for the marbles.
i did offer a pass around earlier in this thread and the offer is still there.
-
Apologies if my post above seemed a little snarky. It certainly wasn't intended that way. It was very late at night here and my words seem to be lacking in humour somewhat :-\
I'm glad it's not painful to work with :)
I did notice your generous offer of a passaround but unfortunately I'm in the UK and have no money to spare to spend on postage :) I'll stick with
over the pics. Thanks for the offer though. 
-
i was not offended at all.

-
@Hedge Kid said:
What an interesting blade cover. It'd be interesting to play with one of these but I'm having difficulty believing that the metalwork in the handle wouldn't become painful with sustained/regular use.

What is JB Weld?i did offer a pass around earlier in this thread and the offer is still there.
That's very generous of you mate

The postage would be fearsome to the UK though, so I'll have to pass sadly :-\
-
Amici,
Marbles products have been manufactured in China since the late 1990's, so unless you're lucky to have come across some old stock thanks again to NAFTA and Bill Clinton you have a Chicom tool..On the other hand, they do use a decent grade of carbon steel in their axe heads so edge retention is not really an issue, but it seems that their earlier products weren't thought out or tested completely so they do come with some stigma attached.
As I mentioned in an earlier post, Marbles products seem to get a regular drubbing in various online forums and deservingly so, although in the last few years their quality has getting better. It seems that anything coming from China nowadays because of their odd tendency of just making and sending it out without any R&D or QC has helped them in being labeled as crap.
As for any axe/hatchet that's not made in the Nordic countries, I would sand down the handle and remove the varnish completely and as mentioned earlier then rub down the tool with liberal amounts of linseed oil and you'll be good to go..
By removing the varnish and using linseed oil, you'll notice the increase in your slide and swing when using the tool.
Cheers,
Serge
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login