Leatherman Charge Ti Rebuild
-
@Grant Lamontagne said:
I remember reading that the Charge TI had allot of issues, hence why it was retired and replaced wit the TTI. One one of the issues was that the file would actually scrape against the liner unless you pushed it to the side as you closed it.. Washer issues maybe?
Cheers,
SergeI have numerous Charges and they all rub. It's got nothing to do with the individual model and more to do with design and construction.
Def
And I've got numerous Charges and none of them do. Weird huh?
-
@Grant Lamontagne said:
I remember reading that the Charge TI had allot of issues, hence why it was retired and replaced wit the TTI. One one of the issues was that the file would actually scrape against the liner unless you pushed it to the side as you closed it.. Washer issues maybe?
Cheers,
SergeI have numerous Charges and they all rub. It's got nothing to do with the individual model and more to do with design and construction.
Def
@Grant Lamontagne said:
I remember reading that the Charge TI had allot of issues, hence why it was retired and replaced wit the TTI. One one of the issues was that the file would actually scrape against the liner unless you pushed it to the side as you closed it.. Washer issues maybe?
Cheers,
SergeI have numerous Charges and they all rub. It's got nothing to do with the individual model and more to do with design and construction.
Def
And I've got numerous Charges and none of them do. Weird huh?
Mine does rub, might have something to do on which market they are going. Might be rubbing on the American market and none on the European market.
-
Maybe, but it's more likely that I've been lucky, or more likely still it's because just about all of my tools are 2nd hand / used and they may have been tweaked / adjusted by the time they get to me - I'm not sure.
That said, the few I have had from new seem fine too! Clearly many people haven't been so fortunate though.
-
It is quite easy to create the rubbing issue, just loosen the screw that holds the file. It then rubs.
Tighten the screw up and the rubbing goes away.The tricky part is getting enough tension so that the file doesn't rub but not so much that the knife blade is stiff.
-
In my personal experience, rubbing problems on liner-locked blades/saws is generally because the hole on the blade is slightly too large for the pivot - if not tightened down properly, the liner will push the blade over to the side instead of just retaining it in the handle. Don't get me wrong though, this is a QC issue, and should be fixable beyond just cranking the tightening screw down on the pivot.
I've not had this particular issues with any Leathermans I've had, but I have had it with CRKT and Kershaw knives. It should be a warranty-able issue - I would suggest e-mailing Leatherman's warranty department and see what they have to say.
Edit: Erm, perhaps not in this case.
-
[quote author=viw9419 link=topic=20872.msg390388#msg390388 date=1277761650]
I can take more pics.It would be easier with 2 torx bits but may be possible with one, if you open the tool(s) it locks the shaft allowing the screw to turn. You are aware that one of the screw heads is part of the shaft, look at my picture.
I used a 3 stage process with varying grades of cotton mops and compounds.
I will add photos soon if anyone is interested.Once it is apart you can lightly file either the liner lock or the back of the blade until it fits but try and make the finish nice and smooth so that the liner slides across the rear of the blade or you may end up taking a little too much off.
Did you polish by hand or with a dremel? I would be interested in knowing the compounds you used so I can duplicate this on my tool.
Or should I just send my tool and a donation ;)
-
All done on a proper polishing machine with 5" wheels. Grey, Green, Blue.
I fly out of the country for a year in less than 1 week so I don't think there will be time unless you send by express.
Up to you mate. If you miss me the postman should return it to you, might take some time to get your tool back though.
-
@viw9419 said:
All done on a proper polishing machine with 5" wheels. Grey, Green, Blue.I fly out of the country for a year in less than 1 week so I don't think there will be time unless you send by express.
Up to you mate. If you miss me the postman should return it to you, might take some time to get your tool back though.
No worries, I'll look into it more in a bit, my son is 3 weeks old so I can talk more than I can do at this point. :)
Thanks for offer!
Are the color wheels different grits?
If you could, just steer me to the website of the maker of the polisher that would be grand!
-
My grandad used to be a polisher and so it has been in the shed as long as I have been alive.
5 mins on google will find you a bench grinder with polishing spindle and a set of mops and pastes/soaps.
All pretty much of a muchness.
-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

