Drop resistant flashlight
-
And just to end I indeed had one(rated) from sunlite who are for industry and it failed,$128 is not cheap ;)
[edit] But the $1 light still shines

-
You might try peli lights, they're a little behind the group on led tech but as far as cases, water proofing and just taking a beating they are top notch,
They also have a life time no quibble guarantee, which means what ever happens just take it to a dealer and they'll give you a new one there and then, doesn't matter how trivial the damage is either I've seen this happen when someone snapped off the pocket clip off theirs
-
Fair enough. I know myself; I have broken a few LED flashlights. Yes, they are not as fragile as bulbs...but I can still break them unfortunately. You probably are right also, the LEDs could still be good, but it doesn't seem to do me a lot of good when everything else fails around them.
-
@Chako said:
Fair enough. I know myself; I have broken a few LED flashlights. Yes, they are not as fragile as bulbs...but I can still break them unfortunately. You probably are right also, the LEDs could still be good, but it doesn't seem to do me a lot of good when everything else fails around them.everything around it,PROTECTS IT

-
Get a decent LED light and wrap it in paracord to add some protection. If something breaks it will be the Cree LED falling off the PCB from the shock.
-
Super glue for the paracord you mean? The cree LED is naturally on the PCB when you buy the flashlight -__-
I have had the actual LED fall off the PCB on a stock flashlight, hence why I know that is the failing point -
@Andreas said:
Super glue for the paracord you mean? The cree LED is naturally on the PCB when you buy the flashlight -__-
I have had the actual LED fall off the PCB on a stock flashlight, hence why I know that is the failing pointyou can have your opinions but how the led is bonded to the board makes a difference ;)
-
Sure, but how in heck am I supposed to know what manufacturers use for that procedure? You comment asking me if I use super glue makes absolutely no sense, that's like asking someone what type of brass rod they used to put together a SAK they just bought from a store
-
@Andreas said:
Sure, but how in heck am I supposed to know what manufacturers use for that procedure? You comment asking me if I use super glue makes absolutely no sense, that's like asking someone what type of brass rod they used to put together a SAK they just bought from a storeNo! I said you like super glue SO WHAT!. What I'm trying to say is: led boards DON'T use super glue ::) ;)
-
That doesn't mean they can't fall off. I've had it happen. After all, most of the electronics in such a light is protected within the light, but the reflector can transfer shock to the LED itself, and that might make it come off if its surface mounted like most are. I'm not saying it will happen, I'm just saying that if anything on the light is going to break, that's likely to be it.
Also I don't like super glue in any particular way; I use it on SAK scales because it works perfectly. I still fail to see what me using super glue for SAK scales have to do with manufacturers not using super glue for LED flashlights.
-
@Andreas said:
That doesn't mean they can't fall off. I've had it happen. After all, most of the electronics in such a light is protected within the light, but the reflector can transfer shock to the LED itself, and that might make it come off if its surface mounted like most are. I'm not saying it will happen, I'm just saying that if anything on the light is going to break, that's likely to be it.Also I don't like super glue in any particular way; I use it on SAK scales because it works perfectly. I still fail to see what me using super glue for SAK scales have to do with manufacturers not using super glue for LED flashlights.
Then it makes no difference who makes it ;) cheap/expensive makes no difference if they bond it in the same way

-
I never said they bond it the same way... I think you need to start reading sentences better, would help avoid a lot of confusion
-
+1 to everybody saying the energizer hard case lights.
I work pest control and part of that involves climbing into some pretty nasty holes under houses. When you're on your way out, gently placing your light down is the last thing on your mind. My lights have fallen 4-6 feet onto concrete more times than I can remember. Neither of my two hard case lights ever broke. The only reason I stopped carrying them is I want something with a little more "heft" when I'm working in the inner city, if you know what I'm mean. So I switched to a 4D cell Maglite LED. This one has taken just as much abuse and keeps on ticking.
If you want something super small, I have a Maglite solitare with a custom LED upgrade in it on my keyring that gets thrown around and bashed around. The finish is so scratched up you can barely tell it used to be black. Still works perfectly though.
Hope that helps a little.

-
I"m going to look into that Hardcase, specifically the yellow one posted. A friend of mine has the gray 2AA Hardcase, but its a 3 LED cluster and kinda dim. The yellow one uses a single LED with a condenser lens which sounds better. Interesting my Fenix E01 is the toughest light I have, but it's too dim for lighting up catwalks and rigging grids in my theatre.
And I forger about Pelican, the old standby.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
you use super glue yes? well FYI the led is held in place with what you choose