Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Rusty scissor pivot

Scheduled Pinned Locked Moved Swiss Army Knights Forum
9 Posts 1 Posters 2.4k Views
  1. Home
  2. Tool Talk
  3. Swiss Army Knights Forum
  4. Rusty scissor pivot
Rusty scissor pivot
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • Fishnuts2 Offline
    Fishnuts2
    Posts: 126
    Fishnuts2 Offline
    Fishnuts2
    wrote on last edited by
    Quote Reply

      What do you recommend to remove the rust from the scissor pivot on my beloved Explorer? I don't have a problem anywhere else on this tool, yet, I use the scissors a lot and would appreciate ideas on how to make them less sticky. (It has a rivet for a pivot)

      Tried 3 in 1, TriFlo, dish soap and warm water, all to no avail. What do you think? ???
      Thanks!

      W

      1 Reply Last reply
      • EZ822 Offline
        EZ822
        Posts: 760
        EZ822 Offline
        EZ822
        wrote on last edited by
        #1 Quote Reply

          I had some rust on the can opener on my Juice S2. I used WD40 and very fine sandpaper to get it out. Worked well for me.

          Erick

          1 Reply Last reply
          • Benner Offline
            Benner
            Posts: 28,081
            Benner Offline
            Benner
            wrote on last edited by
            #2 Quote Reply

              Rust on a Vic?!?! I thought that wasn't possible. :D

              I'm back!!

              1 Reply Last reply
              • stressmaster5000 Offline
                stressmaster5000
                Posts: 3,414
                stressmaster5000 Offline
                stressmaster5000
                wrote on last edited by
                #3 Quote Reply

                  I usually start with a razor blade and scrape any visible areas around the pivot point and then work some oil into it.

                  It might be worth giving some dental floss a shot with some oil on it. Just work it in and around the joint to try and loosen it up. :think:

                  1 Reply Last reply
                  • Fishnuts2 Offline
                    Fishnuts2
                    Posts: 126
                    Fishnuts2 Offline
                    Fishnuts2
                    wrote on last edited by
                    #4 Quote Reply

                      Thanks! I'll give these a try and report back in a few days. :salute:

                      W

                      1 Reply Last reply
                      • Smitty44 Offline
                        Smitty44
                        Posts: 2,026
                        Smitty44 Offline
                        Smitty44
                        wrote on last edited by
                        #5 Quote Reply

                          If that don't work,try liquid wrench penetrating oil. :salute:

                          1 Reply Last reply
                          • ICanFixThat Offline
                            ICanFixThat
                            Posts: 4,534
                            ICanFixThat Offline
                            ICanFixThat
                            wrote on last edited by
                            #6 Quote Reply

                              Or just be sure to work the wd-40 into the pivot and let it sit for some time. I think maybe you were not patient enough.

                              1 Reply Last reply
                              • Singh Offline
                                Singh
                                Posts: 1,634
                                Singh Offline
                                Singh
                                wrote on last edited by
                                #7 Quote Reply

                                  all good suggestions.

                                  I'd soak it in mineral spirits and scrub it with a soft copper brush.

                                  Merit Badges
                                  Time Lord Level 2 Flashlight Airgun User Hook User Mod User ALOX with Scissors Scale Changer Time Lord Level 3 Paracord Duct Tape Chainsaw User Minimal SAK Challenge Titanium Zip Tie User Axe User Mora User Camo SAK
                                  1 Reply Last reply
                                  • Marlinaholic Offline
                                    Marlinaholic
                                    Posts: 118
                                    Marlinaholic Offline
                                    Marlinaholic
                                    wrote on last edited by
                                    #8 Quote Reply

                                      Soft copper or brass bristle brush is a good idea, it won't mar or scratch up the steel. Should work great, but soak it in some sort of oil ect. first to soften up the rust.

                                      1 Reply Last reply

                                      Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                      Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                      With your input, this post could be even better 💗

                                      Register Login

                                      1. Home
                                      2. Tool Talk
                                      3. Swiss Army Knights Forum
                                      4. Rusty scissor pivot
                                      Reply
                                      • Reply as topic
                                      Log in to reply
                                      COMMUNITY LINKS
                                      EDC-TV SAKWiki GearFeed SAKSelector
                                      Operational Funds

                                      Help us keep the Unworkable working!

                                      Make A Donation
                                      November Goal: $300.00
                                      Due Date: Nov 30
                                      Total Receipts: $0.00
                                      Below Goal: $300.00
                                      0% funded
                                      • Login

                                      • Don't have an account? Register

                                      • Login or register to search.
                                      • First post
                                        Last post
                                      0