Show your slip joint's thread!
-
dks,
Well, they did have the Colt listed correctly as it is Brown Stag Bone.
Even outside contacting the dealer, if you are unsure of something don't hesitate to fire me off a PM here on the board. I am usually on here a couple times a day, I'll do what I can to help you. No problem.

As to that Colt, when working down the kick use a small file and just go slowly. Very small increments. And check your progress often, remove a little and close the blade.
And that particular Colt is from the highest end range they do in that line. With it's fancy bolsters, swedged blades, long pulls, all mirror polished, and the boxes they come with it is their more expensive line. Not sure if you are into the Gunstock pattern but they have two different Gunstocks in this line and they are really sweet..........


It's the only two I have from this particular series of Colts, been meaning to get more.
And I understand about the sending of items back to the companies for replacement or repair. Living overseas it can be a pain to get things back to the States due to cost. And especially if they are American made as they usually already cost a small fortune over there. :(
2xTap
-
@Sean said:
They did come with a bevel so I used the sharpmaker on them. However, I might just
have to fiddle with the angle a bit something which your limited with on that particular
device.Sean,
Ok, yeah.......I have no experience with those types of sharpeners. I have so many knives that come with all sorts of angles to their bevels as well as those I have with full convex grinds and convex edges that I just free-hand all my sharpening.
With my Case knives the bevels are usually at a good angle from the factory. I've had excellent results with just a ceramic two-sided pocket stone to keep a hair popping edge on my Case pieces that I use. If I let them get too dull I'll hit the edges quick with a few laps on a small Eze-Lap diamond stone I have and then fine up the edge on my ceramic.....followed by some light stropping on some bare leather. Shaving sharp!
2xTap
-
Thanks for the info 2xtap! I'll work with the systems I have and see how the edge
comes up for me. You certainly have more versatility using the freehand method
and I'm sure once I work with the Cases a bit more I can bring up the edges nicely
as well. :) -
This one arrived a few days ago, one of several I am getting from a collection a friend is selling me. And I got this one for a song!



1994 production Case Classic #3055 Wharncliffe Whittler in unused minty shape. It came with the original box and wrap but was missing all the paperwork. Not sweating it though considering how cheap I got this one for.


And it's a Split-Back........

It's 3 5/8" closed. Blades are polished 1095 carbon steel with nickle/silver bolsters and shield, and brass pins and liners. F&F is excellent, the only thing I found on this was some very light pepper on the backsprings which most disappeared after some light rubbing with Flitz.
Sorry about the pics, the muted sunlight I was getting from the overcast skies today made the color of the scales come through noticably brighter and more orange than they really are. The bone on this is more of a tan/caramel color. Not sure of the actual name as I've seen this bone called many things but I believe the actual name is Antique Green (even though there ain't a bit of green in them)......not sure though.
Anyway, a real nice piece to add to my very small but growing collection of CC's.

2xTap
-
Zed, good luck.
2xtap, I am already looking at the various patterns in that range....... :D By the way, usually I can not see the pictures you post, I just get a picture of a frog and a message saying "domain unregistered. to view register at ....domain name" . I do not know whether the problem is with my service provider or the picture hosting site.
-
dks,
Hmmmmm, that's weird. I see all my pics showing up. I direct link my pics from ImageShack. This is the first time I've heard anyone not being able to see my pics.
Anyone else not able to see these above?
2xTap
-
I never have troubles seeing the pics. I see the pics of a lovely wharnie!

-
Sadly I see them no problem. Why sadly? They make me want to spend more money!

-
Ok, so others can see them.
dks, it might be something with your set-up that is blocking the pics. Possibly your service provider.
2xTap
-
Here's another I just got recently. This one a new release by Kissing Crane.........


A Scout pattern done in the standard 4-blade configuration. Closed length is 3 3/4" with 420 stainless steel mainblade/awl/bottle opener-screwdriver/can opener. Bolsters and shield are nickle/silver, and the liners and pins are brass. Blades and backspring area are brush finished with a mirror polish everywhere else. Scales are Olive Green jigged bone.

Fit and finish is very good with even edge grinds that are sharp, zero blade play anywhere, backsprings have a good stoutness on all four, bail swings tight, the only fault I could find was in the backspring area where there are a few minor hairline gaps........

Overall not a bad piece at all. These are still made in China and are of the most recent releases since the brand is no longer associated with the Robert Klaas name. Not bad for a Scout costing a little over $20 but the Rough Rider version I believe is still a better buy in this pattern.
2xTap
-
@2xTap said:
Here's another I just got recently. This one a new release by Kissing Crane.........

A Scout pattern done in the standard 4-blade configuration. Closed length is 3 3/4" with 420 stainless steel mainblade/awl/bottle opener-screwdriver/can opener. Bolsters and shield are nickle/silver, and the liners and pins are brass. Blades and backspring area are brush finished with a mirror polish everywhere else. Scales are Olive Green jigged bone.

Fit and finish is very good with even edge grinds that are sharp, zero blade play anywhere, backsprings have a good stoutness on all four, bail swings tight, the only fault I could find was in the backspring area where there are a few minor hairline gaps........

Overall not a bad piece at all. These are still made in China and are of the most recent releases since the brand is no longer associated with the Robert Klaas name. Not bad for a Scout costing a little over $20 but the Rough Rider version I believe is still a better buy in this pattern.
2xTap
i really like that 2xtap , ive not seen the RR scout as i dont think HH do it on there site, ill have to take another look
love the scales on thay, -
sorry for mulit post i had problems posting this am :-[
-
-
Zed,
The Rough Rider versions are still being made, not sure of the place where you buy yours but they can be found. The Rough Rider Scout is a bit more burly than this KC version, and it's also designed off of a much older version of the Scout. And the RR version has a nicer finish being all mirror polished......as well as being cheaper. I picked up both of my Rough Rider Scouts combined for the cost of this single KC version.
2xTap
-
The Rough Rider versions are still being made, not sure of the place where you buy yours but they can be found. The Rough Rider Scout is a bit more burly than this KC version, and it's also designed off of a much older version of the Scout. And the RR version has a nicer finish being all mirror polished......as well as being cheaper. I picked up both of my Rough Rider Scouts combined for the cost of this single KC version.
2xTap
cheers 2xtap ill see what comes up, HH dont have it on there site so ill google and see :D

-
:ahhh this am postelk ridge stockman

schrade custom series whittler

RR peanut

Kissing cranes congress

-
Good buys, I have been wondering about Elk ridge knives for some time, but that wooden scaled one looks very nice. Nice bone on the Kissing Crane too.

I like the schrade´s pattern too, though I have found their finish hit and miss, usually the ends of the knife’s blade (I am sure they have a name..) touching the springs are not polished properly making them feel rough when opening or closing.
I am sure you will enjoy them all, the RR should be the best quality one, I assume.
Any, preliminary, observations?

As for the scout knives, if you are interested, I got one some time ago of THE auction site, for a very reasonable price nad they can still be found there, I posted a bit about it in the review section a few weeks back (yes I know, shameless self promotion >:D ).
-
@dks said:
Good buys, I have been wondering about Elk ridge knives for some time, but that wooden scaled one looks very nice. Nice bone on the Kissing Crane too.
I like the schrade´s pattern too, though I have found their finish hit and miss, usually the ends of the knife’s blade (I am sure they have a name..) touching the springs are not polished properly making them feel rough when opening or closing.
I am sure you will enjoy them all, the RR should be the best quality one, I assume.
Any, preliminary, observations?

As for the scout knives, if you are interested, I got one some time ago of THE auction site, for a very reasonable price nad they can still be found there, I posted a bit about it in the review section a few weeks back (yes I know, shameless self promotion >:D ).
well the RR peanut all seems solid for its little size, the cane creek has a 2 stop click (think thats what its called lol) very solid and fit and finnish spot on, the elk ridge doesnt have the same snap to the blades when opend but all finnish is very nice, main blade is like a toothpick in shape, scales really nice, my favourite is the schrade, the fit and finnish is very good and all blades snap nicely into place, i love the scales and there well fitted, all good ,
oh all blades pretty sharp , the peanuts are very sharp out the box as usual, -
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
